.. SPDX-License-Identifier: CC-BY-SA-2.0-UK ******* Classes ******* Class files are used to abstract common functionality and share it amongst multiple recipe (``.bb``) files. To use a class file, you simply make sure the recipe inherits the class. In most cases, when a recipe inherits a class it is enough to enable its features. There are cases, however, where in the recipe you might need to set variables or override some default behavior. Any :term:`Metadata` usually found in a recipe can also be placed in a class file. Class files are identified by the extension ``.bbclass`` and are usually placed in one of a set of subdirectories beneath the ``meta*/`` directory found in the :term:`Source Directory`: - ``classes-recipe/`` - classes intended to be inherited by recipes individually - ``classes-global/`` - classes intended to be inherited globally - ``classes/`` - classes whose usage context is not clearly defined Class files can also be pointed to by :term:`BUILDDIR` (e.g. ``build/``) in the same way as ``.conf`` files in the ``conf`` directory. Class files are searched for in :term:`BBPATH` using the same method by which ``.conf`` files are searched. This chapter discusses only the most useful and important classes. Other classes do exist within the ``meta/classes*`` directories in the Source Directory. You can reference the ``.bbclass`` files directly for more information. .. _ref-classes-allarch: ``allarch`` =========== The :ref:`ref-classes-allarch` class is inherited by recipes that do not produce architecture-specific output. The class disables functionality that is normally needed for recipes that produce executable binaries (such as building the cross-compiler and a C library as pre-requisites, and splitting out of debug symbols during packaging). .. note:: Unlike some distro recipes (e.g. Debian), OpenEmbedded recipes that produce packages that depend on tunings through use of the :term:`RDEPENDS` and :term:`TUNE_PKGARCH` variables, should never be configured for all architectures using :ref:`ref-classes-allarch`. This is the case even if the recipes do not produce architecture-specific output. Configuring such recipes for all architectures causes the :ref:`do_package_write_* ` tasks to have different signatures for the machines with different tunings. Additionally, unnecessary rebuilds occur every time an image for a different :term:`MACHINE` is built even when the recipe never changes. By default, all recipes inherit the :ref:`ref-classes-base` and :ref:`ref-classes-package` classes, which enable functionality needed for recipes that produce executable output. If your recipe, for example, only produces packages that contain configuration files, media files, or scripts (e.g. Python and Perl), then it should inherit the :ref:`ref-classes-allarch` class. .. _ref-classes-archiver: ``archiver`` ============ The :ref:`ref-classes-archiver` class supports releasing source code and other materials with the binaries. For more details on the source :ref:`ref-classes-archiver`, see the ":ref:`dev-manual/licenses:maintaining open source license compliance during your product's lifecycle`" section in the Yocto Project Development Tasks Manual. You can also see the :term:`ARCHIVER_MODE` variable for information about the variable flags (varflags) that help control archive creation. .. _ref-classes-autotools: ``autotools*`` ============== The :ref:`autotools* ` classes support packages built with the :wikipedia:`GNU Autotools `. The ``autoconf``, ``automake``, and ``libtool`` packages bring standardization. This class defines a set of tasks (e.g. ``configure``, ``compile`` and so forth) that work for all Autotooled packages. It should usually be enough to define a few standard variables and then simply ``inherit autotools``. These classes can also work with software that emulates Autotools. For more information, see the ":ref:`dev-manual/new-recipe:building an autotooled package`" section in the Yocto Project Development Tasks Manual. By default, the :ref:`autotools* ` classes use out-of-tree builds (i.e. ``autotools.bbclass`` building with ``B != S``). If the software being built by a recipe does not support using out-of-tree builds, you should have the recipe inherit the :ref:`autotools-brokensep ` class. The :ref:`autotools-brokensep ` class behaves the same as the :ref:`ref-classes-autotools` class but builds with :term:`B` == :term:`S`. This method is useful when out-of-tree build support is either not present or is broken. .. note:: It is recommended that out-of-tree support be fixed and used if at all possible. It's useful to have some idea of how the tasks defined by the :ref:`autotools* ` classes work and what they do behind the scenes. - :ref:`ref-tasks-configure` --- regenerates the configure script (using ``autoreconf``) and then launches it with a standard set of arguments used during cross-compilation. You can pass additional parameters to ``configure`` through the :term:`EXTRA_OECONF` or :term:`PACKAGECONFIG_CONFARGS` variables. - :ref:`ref-tasks-compile` --- runs ``make`` with arguments that specify the compiler and linker. You can pass additional arguments through the :term:`EXTRA_OEMAKE` variable. - :ref:`ref-tasks-install` --- runs ``make install`` and passes in ``${``\ :term:`D`\ ``}`` as ``DESTDIR``. .. _ref-classes-base: ``base`` ======== The :ref:`ref-classes-base` class is special in that every ``.bb`` file implicitly inherits the class. This class contains definitions for standard basic tasks such as fetching, unpacking, configuring (empty by default), compiling (runs any ``Makefile`` present), installing (empty by default) and packaging (empty by default). These tasks are often overridden or extended by other classes such as the :ref:`ref-classes-autotools` class or the :ref:`ref-classes-package` class. The class also contains some commonly used functions such as ``oe_runmake``, which runs ``make`` with the arguments specified in :term:`EXTRA_OEMAKE` variable as well as the arguments passed directly to ``oe_runmake``. .. _ref-classes-bash-completion: ``bash-completion`` =================== Sets up packaging and dependencies appropriate for recipes that build software that includes bash-completion data. .. _ref-classes-bin-package: ``bin_package`` =============== The :ref:`ref-classes-bin-package` class is a helper class for recipes that extract the contents of a binary package (e.g. an RPM) and install those contents rather than building the binary from source. The binary package is extracted and new packages in the configured output package format are created. Extraction and installation of proprietary binaries is a good example use for this class. .. note:: For RPMs and other packages that do not contain a subdirectory, you should specify an appropriate fetcher parameter to point to the subdirectory. For example, if BitBake is using the Git fetcher (``git://``), the "subpath" parameter limits the checkout to a specific subpath of the tree. Here is an example where ``${BP}`` is used so that the files are extracted into the subdirectory expected by the default value of :term:`S`:: SRC_URI = "git://example.com/downloads/somepackage.rpm;branch=main;subpath=${BP}" See the ":ref:`bitbake-user-manual/bitbake-user-manual-fetching:fetchers`" section in the BitBake User Manual for more information on supported BitBake Fetchers. .. _ref-classes-binconfig: ``binconfig`` ============= The :ref:`ref-classes-binconfig` class helps to correct paths in shell scripts. Before ``pkg-config`` had become widespread, libraries shipped shell scripts to give information about the libraries and include paths needed to build software (usually named ``LIBNAME-config``). This class assists any recipe using such scripts. During staging, the OpenEmbedded build system installs such scripts into the ``sysroots/`` directory. Inheriting this class results in all paths in these scripts being changed to point into the ``sysroots/`` directory so that all builds that use the script use the correct directories for the cross compiling layout. See the :term:`BINCONFIG_GLOB` variable for more information. .. _ref-classes-binconfig-disabled: ``binconfig-disabled`` ====================== An alternative version of the :ref:`ref-classes-binconfig` class, which disables binary configuration scripts by making them return an error in favor of using ``pkg-config`` to query the information. The scripts to be disabled should be specified using the :term:`BINCONFIG` variable within the recipe inheriting the class. .. _ref-classes-buildhistory: ``buildhistory`` ================ The :ref:`ref-classes-buildhistory` class records a history of build output metadata, which can be used to detect possible regressions as well as used for analysis of the build output. For more information on using Build History, see the ":ref:`dev-manual/build-quality:maintaining build output quality`" section in the Yocto Project Development Tasks Manual. .. _ref-classes-buildstats: ``buildstats`` ============== The :ref:`ref-classes-buildstats` class records performance statistics about each task executed during the build (e.g. elapsed time, CPU usage, and I/O usage). When you use this class, the output goes into the :term:`BUILDSTATS_BASE` directory, which defaults to ``${TMPDIR}/buildstats/``. You can analyze the elapsed time using ``scripts/pybootchartgui/pybootchartgui.py``, which produces a cascading chart of the entire build process and can be useful for highlighting bottlenecks. Collecting build statistics is enabled by default through the :term:`USER_CLASSES` variable from your ``local.conf`` file. Consequently, you do not have to do anything to enable the class. However, if you want to disable the class, simply remove ":ref:`ref-classes-buildstats`" from the :term:`USER_CLASSES` list. .. _ref-classes-buildstats-summary: ``buildstats-summary`` ====================== When inherited globally, prints statistics at the end of the build on sstate re-use. In order to function, this class requires the :ref:`ref-classes-buildstats` class be enabled. .. _ref-classes-cargo: ``cargo`` ========= The :ref:`ref-classes-cargo` class allows to compile Rust language programs using `Cargo `__. Cargo is Rust's package manager, allowing to fetch package dependencies and build your program. Using this class makes it very easy to build Rust programs. All you need is to use the :term:`SRC_URI` variable to point to a source repository which can be built by Cargo, typically one that was created by the ``cargo new`` command, containing a ``Cargo.toml`` file, a ``Cargo.lock`` file and a ``src`` subdirectory. If you want to build and package tests of the program, inherit the :ref:`ref-classes-ptest-cargo` class instead of :ref:`ref-classes-cargo`. You will find an example (that show also how to handle possible git source dependencies) in the :oe_git:`zvariant_3.12.0.bb ` recipe. Another example, with only crate dependencies, is the :oe_git:`uutils-coreutils ` recipe, which was generated by the `cargo-bitbake `__ tool. This class inherits the :ref:`ref-classes-cargo_common` class. .. _ref-classes-cargo_c: ``cargo_c`` =========== The :ref:`ref-classes-cargo_c` class can be inherited by a recipe to generate a Rust library that can be called by C/C++ code. The recipe which inherits this class has to only replace ``inherit cargo`` by ``inherit cargo_c``. See the :yocto_git:`rust-c-lib-example_git.bb ` example recipe. .. _ref-classes-cargo_common: ``cargo_common`` ================ The :ref:`ref-classes-cargo_common` class is an internal class that is not intended to be used directly. An exception is the "rust" recipe, to build the Rust compiler and runtime library, which is built by Cargo but cannot use the :ref:`ref-classes-cargo` class. This is why this class was introduced. .. _ref-classes-cargo-update-recipe-crates: ``cargo-update-recipe-crates`` =============================== The :ref:`ref-classes-cargo-update-recipe-crates` class allows recipe developers to update the list of Cargo crates in :term:`SRC_URI` by reading the ``Cargo.lock`` file in the source tree. To do so, create a recipe for your program, for example using :doc:`devtool `, make it inherit the :ref:`ref-classes-cargo` and :ref:`ref-classes-cargo-update-recipe-crates` and run:: bitbake -c update_crates recipe This creates a ``recipe-crates.inc`` file that you can include in your recipe:: require ${BPN}-crates.inc That's also something you can achieve by using the `cargo-bitbake `__ tool. .. _ref-classes-ccache: ``ccache`` ========== The :ref:`ref-classes-ccache` class enables the C/C++ Compiler Cache for the build. This class is used to give a minor performance boost during the build. See https://ccache.samba.org/ for information on the C/C++ Compiler Cache, and the :oe_git:`ccache.bbclass ` file for details about how to enable this mechanism in your configuration file, how to disable it for specific recipes, and how to share ``ccache`` files between builds. However, using the class can lead to unexpected side-effects. Thus, using this class is not recommended. .. _ref-classes-chrpath: ``chrpath`` =========== The :ref:`ref-classes-chrpath` class is a wrapper around the "chrpath" utility, which is used during the build process for :ref:`ref-classes-nativesdk`, :ref:`ref-classes-cross`, and :ref:`ref-classes-cross-canadian` recipes to change ``RPATH`` records within binaries in order to make them relocatable. .. _ref-classes-cmake: ``cmake`` ========= The :ref:`ref-classes-cmake` class allows recipes to build software using the `CMake `__ build system. You can use the :term:`EXTRA_OECMAKE` variable to specify additional configuration options to pass to the ``cmake`` command line. By default, the :ref:`ref-classes-cmake` class uses `Ninja `__ instead of GNU make for building, which offers better build performance. If a recipe is broken with Ninja, then the recipe can set the :term:`OECMAKE_GENERATOR` variable to ``Unix Makefiles`` to use GNU make instead. If you need to install custom CMake toolchain files supplied by the application being built, you should install them (during :ref:`ref-tasks-install`) to the preferred CMake Module directory: ``${D}${datadir}/cmake/modules/``. .. _ref-classes-cml1: ``cml1`` ======== The :ref:`ref-classes-cml1` class provides basic support for the Linux kernel style build configuration system. "cml" stands for "Configuration Menu Language", which originates from the Linux kernel but is also used in other projects such as U-Boot and BusyBox. It could have been called "kconfig" too. .. _ref-classes-compress_doc: ``compress_doc`` ================ Enables compression for manual and info pages. This class is intended to be inherited globally. The default compression mechanism is gz (gzip) but you can select an alternative mechanism by setting the :term:`DOC_COMPRESS` variable. .. _ref-classes-copyleft_compliance: ``copyleft_compliance`` ======================= The :ref:`ref-classes-copyleft_compliance` class preserves source code for the purposes of license compliance. This class is an alternative to the :ref:`ref-classes-archiver` class and is still used by some users even though it has been deprecated in favor of the :ref:`ref-classes-archiver` class. .. _ref-classes-copyleft_filter: ``copyleft_filter`` =================== A class used by the :ref:`ref-classes-archiver` and :ref:`ref-classes-copyleft_compliance` classes for filtering licenses. The ``copyleft_filter`` class is an internal class and is not intended to be used directly. .. _ref-classes-core-image: ``core-image`` ============== The :ref:`ref-classes-core-image` class provides common definitions for the ``core-image-*`` image recipes, such as support for additional :term:`IMAGE_FEATURES`. .. _ref-classes-cpan: ``cpan*`` ========= The :ref:`cpan* ` classes support Perl modules. Recipes for Perl modules are simple. These recipes usually only need to point to the source's archive and then inherit the proper class file. Building is split into two methods depending on which method the module authors used. - Modules that use old ``Makefile.PL``-based build system require ``cpan.bbclass`` in their recipes. - Modules that use ``Build.PL``-based build system require using ``cpan_build.bbclass`` in their recipes. Both build methods inherit the :ref:`cpan-base ` class for basic Perl support. .. _ref-classes-create-spdx: ``create-spdx`` =============== The :ref:`ref-classes-create-spdx` class provides support for automatically creating :term:`SPDX` :term:`SBOM` documents based upon image and SDK contents. This class is meant to be inherited globally from a configuration file:: INHERIT += "create-spdx" The toplevel :term:`SPDX` output file is generated in JSON format as a ``IMAGE-MACHINE.spdx.json`` file in ``tmp/deploy/images/MACHINE/`` inside the :term:`Build Directory`. There are other related files in the same directory, as well as in ``tmp/deploy/spdx``. The exact behaviour of this class, and the amount of output can be controlled by the :term:`SPDX_PRETTY`, :term:`SPDX_ARCHIVE_PACKAGED`, :term:`SPDX_ARCHIVE_SOURCES` and :term:`SPDX_INCLUDE_SOURCES` variables. See the description of these variables and the ":ref:`dev-manual/sbom:creating a software bill of materials`" section in the Yocto Project Development Manual for more details. .. _ref-classes-cross: ``cross`` ========= The :ref:`ref-classes-cross` class provides support for the recipes that build the cross-compilation tools. .. _ref-classes-cross-canadian: ``cross-canadian`` ================== The :ref:`ref-classes-cross-canadian` class provides support for the recipes that build the Canadian Cross-compilation tools for SDKs. See the ":ref:`overview-manual/concepts:cross-development toolchain generation`" section in the Yocto Project Overview and Concepts Manual for more discussion on these cross-compilation tools. .. _ref-classes-crosssdk: ``crosssdk`` ============ The :ref:`ref-classes-crosssdk` class provides support for the recipes that build the cross-compilation tools used for building SDKs. See the ":ref:`overview-manual/concepts:cross-development toolchain generation`" section in the Yocto Project Overview and Concepts Manual for more discussion on these cross-compilation tools. .. _ref-classes-cve-check: ``cve-check`` ============= The :ref:`ref-classes-cve-check` class looks for known CVEs (Common Vulnerabilities and Exposures) while building with BitBake. This class is meant to be inherited globally from a configuration file:: INHERIT += "cve-check" To filter out obsolete CVE database entries which are known not to impact software from Poky and OE-Core, add following line to the build configuration file:: include cve-extra-exclusions.inc You can also look for vulnerabilities in specific packages by passing ``-c cve_check`` to BitBake. After building the software with Bitbake, CVE check output reports are available in ``tmp/deploy/cve`` and image specific summaries in ``tmp/deploy/images/*.cve`` or ``tmp/deploy/images/*.json`` files. When building, the CVE checker will emit build time warnings for any detected issues which are in the state ``Unpatched``, meaning that CVE issue seems to affect the software component and version being compiled and no patches to address the issue are applied. Other states for detected CVE issues are: ``Patched`` meaning that a patch to address the issue is already applied, and ``Ignored`` meaning that the issue can be ignored. The ``Patched`` state of a CVE issue is detected from patch files with the format ``CVE-ID.patch``, e.g. ``CVE-2019-20633.patch``, in the :term:`SRC_URI` and using CVE metadata of format ``CVE: CVE-ID`` in the commit message of the patch file. If the recipe adds ``CVE-ID`` as flag of the :term:`CVE_STATUS` variable with status mapped to ``Ignored``, then the CVE state is reported as ``Ignored``:: CVE_STATUS[CVE-2020-15523] = "not-applicable-platform: Issue only applies on Windows" If CVE check reports that a recipe contains false positives or false negatives, these may be fixed in recipes by adjusting the CVE product name using :term:`CVE_PRODUCT` and :term:`CVE_VERSION` variables. :term:`CVE_PRODUCT` defaults to the plain recipe name :term:`BPN` which can be adjusted to one or more CVE database vendor and product pairs using the syntax:: CVE_PRODUCT = "flex_project:flex" where ``flex_project`` is the CVE database vendor name and ``flex`` is the product name. Similarly if the default recipe version :term:`PV` does not match the version numbers of the software component in upstream releases or the CVE database, then the :term:`CVE_VERSION` variable can be used to set the CVE database compatible version number, for example:: CVE_VERSION = "2.39" Any bugs or missing or incomplete information in the CVE database entries should be fixed in the CVE database via the `NVD feedback form `__. Users should note that security is a process, not a product, and thus also CVE checking, analyzing results, patching and updating the software should be done as a regular process. The data and assumptions required for CVE checker to reliably detect issues are frequently broken in various ways. These can only be detected by reviewing the details of the issues and iterating over the generated reports, and following what happens in other Linux distributions and in the greater open source community. You will find some more details in the ":ref:`dev-manual/vulnerabilities:checking for vulnerabilities`" section in the Development Tasks Manual. .. _ref-classes-debian: ``debian`` ========== The :ref:`ref-classes-debian` class renames output packages so that they follow the Debian naming policy (i.e. ``glibc`` becomes ``libc6`` and ``glibc-devel`` becomes ``libc6-dev``.) Renaming includes the library name and version as part of the package name. If a recipe creates packages for multiple libraries (shared object files of ``.so`` type), use the :term:`LEAD_SONAME` variable in the recipe to specify the library on which to apply the naming scheme. .. _ref-classes-deploy: ``deploy`` ========== The :ref:`ref-classes-deploy` class handles deploying files to the :term:`DEPLOY_DIR_IMAGE` directory. The main function of this class is to allow the deploy step to be accelerated by shared state. Recipes that inherit this class should define their own :ref:`ref-tasks-deploy` function to copy the files to be deployed to :term:`DEPLOYDIR`, and use ``addtask`` to add the task at the appropriate place, which is usually after :ref:`ref-tasks-compile` or :ref:`ref-tasks-install`. The class then takes care of staging the files from :term:`DEPLOYDIR` to :term:`DEPLOY_DIR_IMAGE`. .. _ref-classes-devicetree: ``devicetree`` ============== The :ref:`ref-classes-devicetree` class allows to build a recipe that compiles device tree source files that are not in the kernel tree. The compilation of out-of-tree device tree sources is the same as the kernel in-tree device tree compilation process. This includes the ability to include sources from the kernel such as SoC ``dtsi`` files as well as C header files, such as ``gpio.h``. The :ref:`ref-tasks-compile` task will compile two kinds of files: - Regular device tree sources with a ``.dts`` extension. - Device tree overlays, detected from the presence of the ``/plugin/;`` string in the file contents. This class deploys the generated device tree binaries into ``${``\ :term:`DEPLOY_DIR_IMAGE`\ ``}/devicetree/``. This is similar to what the :ref:`ref-classes-kernel-devicetree` class does, with the added ``devicetree`` subdirectory to avoid name clashes. Additionally, the device trees are populated into the sysroot for access via the sysroot from within other recipes. By default, all device tree sources located in :term:`DT_FILES_PATH` directory are compiled. To select only particular sources, set :term:`DT_FILES` to a space-separated list of files (relative to :term:`DT_FILES_PATH`). For convenience, both ``.dts`` and ``.dtb`` extensions can be used. An extra padding is appended to non-overlay device trees binaries. This can typically be used as extra space for adding extra properties at boot time. The padding size can be modified by setting :term:`DT_PADDING_SIZE` to the desired size, in bytes. See :oe_git:`devicetree.bbclass sources ` for further variables controlling this class. Here is an excerpt of an example ``recipes-kernel/linux/devicetree-acme.bb`` recipe inheriting this class:: inherit devicetree COMPATIBLE_MACHINE = "^mymachine$" SRC_URI:mymachine = "file://mymachine.dts" .. _ref-classes-devshell: ``devshell`` ============ The :ref:`ref-classes-devshell` class adds the :ref:`ref-tasks-devshell` task. Distribution policy dictates whether to include this class. See the ":ref:`dev-manual/development-shell:using a development shell`" section in the Yocto Project Development Tasks Manual for more information about using :ref:`ref-classes-devshell`. .. _ref-classes-devupstream: ``devupstream`` =============== The :ref:`ref-classes-devupstream` class uses :term:`BBCLASSEXTEND` to add a variant of the recipe that fetches from an alternative URI (e.g. Git) instead of a tarball. Here is an example:: BBCLASSEXTEND = "devupstream:target" SRC_URI:class-devupstream = "git://git.example.com/example;branch=main" SRCREV:class-devupstream = "abcd1234" Adding the above statements to your recipe creates a variant that has :term:`DEFAULT_PREFERENCE` set to "-1". Consequently, you need to select the variant of the recipe to use it. Any development-specific adjustments can be done by using the ``class-devupstream`` override. Here is an example:: DEPENDS:append:class-devupstream = " gperf-native" do_configure:prepend:class-devupstream() { touch ${S}/README } The class currently only supports creating a development variant of the target recipe, not :ref:`ref-classes-native` or :ref:`ref-classes-nativesdk` variants. The :term:`BBCLASSEXTEND` syntax (i.e. ``devupstream:target``) provides support for :ref:`ref-classes-native` and :ref:`ref-classes-nativesdk` variants. Consequently, this functionality can be added in a future release. Support for other version control systems such as Subversion is limited due to BitBake's automatic fetch dependencies (e.g. ``subversion-native``). .. _ref-classes-externalsrc: ``externalsrc`` =============== The :ref:`ref-classes-externalsrc` class supports building software from source code that is external to the OpenEmbedded build system. Building software from an external source tree means that the build system's normal fetch, unpack, and patch process is not used. By default, the OpenEmbedded build system uses the :term:`S` and :term:`B` variables to locate unpacked recipe source code and to build it, respectively. When your recipe inherits the :ref:`ref-classes-externalsrc` class, you use the :term:`EXTERNALSRC` and :term:`EXTERNALSRC_BUILD` variables to ultimately define :term:`S` and :term:`B`. By default, this class expects the source code to support recipe builds that use the :term:`B` variable to point to the directory in which the OpenEmbedded build system places the generated objects built from the recipes. By default, the :term:`B` directory is set to the following, which is separate from the source directory (:term:`S`):: ${WORKDIR}/${BPN}-{PV}/ See these variables for more information: :term:`WORKDIR`, :term:`BPN`, and :term:`PV`, For more information on the :ref:`ref-classes-externalsrc` class, see the comments in ``meta/classes/externalsrc.bbclass`` in the :term:`Source Directory`. For information on how to use the :ref:`ref-classes-externalsrc` class, see the ":ref:`dev-manual/building:building software from an external source`" section in the Yocto Project Development Tasks Manual. .. _ref-classes-extrausers: ``extrausers`` ============== The :ref:`ref-classes-extrausers` class allows additional user and group configuration to be applied at the image level. Inheriting this class either globally or from an image recipe allows additional user and group operations to be performed using the :term:`EXTRA_USERS_PARAMS` variable. .. note:: The user and group operations added using the :ref:`ref-classes-extrausers` class are not tied to a specific recipe outside of the recipe for the image. Thus, the operations can be performed across the image as a whole. Use the :ref:`ref-classes-useradd` class to add user and group configuration to a specific recipe. Here is an example that uses this class in an image recipe:: inherit extrausers EXTRA_USERS_PARAMS = "\ useradd -p '' tester; \ groupadd developers; \ userdel nobody; \ groupdel -g video; \ groupmod -g 1020 developers; \ usermod -s /bin/sh tester; \ " Here is an example that adds two users named "tester-jim" and "tester-sue" and assigns passwords. First on host, create the (escaped) password hash:: printf "%q" $(mkpasswd -m sha256crypt tester01) The resulting hash is set to a variable and used in ``useradd`` command parameters:: inherit extrausers PASSWD = "\$X\$ABC123\$A-Long-Hash" EXTRA_USERS_PARAMS = "\ useradd -p '${PASSWD}' tester-jim; \ useradd -p '${PASSWD}' tester-sue; \ " Finally, here is an example that sets the root password:: inherit extrausers EXTRA_USERS_PARAMS = "\ usermod -p '${PASSWD}' root; \ " .. note:: From a security perspective, hardcoding a default password is not generally a good idea or even legal in some jurisdictions. It is recommended that you do not do this if you are building a production image. .. _ref-classes-features_check: ``features_check`` ================== The :ref:`ref-classes-features_check` class allows individual recipes to check for required and conflicting :term:`DISTRO_FEATURES`, :term:`MACHINE_FEATURES` or :term:`COMBINED_FEATURES`. This class provides support for the following variables: - :term:`REQUIRED_DISTRO_FEATURES` - :term:`CONFLICT_DISTRO_FEATURES` - :term:`ANY_OF_DISTRO_FEATURES` - ``REQUIRED_MACHINE_FEATURES`` - ``CONFLICT_MACHINE_FEATURES`` - ``ANY_OF_MACHINE_FEATURES`` - ``REQUIRED_COMBINED_FEATURES`` - ``CONFLICT_COMBINED_FEATURES`` - ``ANY_OF_COMBINED_FEATURES`` If any conditions specified in the recipe using the above variables are not met, the recipe will be skipped, and if the build system attempts to build the recipe then an error will be triggered. .. _ref-classes-fontcache: ``fontcache`` ============= The :ref:`ref-classes-fontcache` class generates the proper post-install and post-remove (postinst and postrm) scriptlets for font packages. These scriptlets call ``fc-cache`` (part of ``Fontconfig``) to add the fonts to the font information cache. Since the cache files are architecture-specific, ``fc-cache`` runs using QEMU if the postinst scriptlets need to be run on the build host during image creation. If the fonts being installed are in packages other than the main package, set :term:`FONT_PACKAGES` to specify the packages containing the fonts. .. _ref-classes-fs-uuid: ``fs-uuid`` =========== The :ref:`ref-classes-fs-uuid` class extracts UUID from ``${``\ :term:`ROOTFS`\ ``}``, which must have been built by the time that this function gets called. The :ref:`ref-classes-fs-uuid` class only works on ``ext`` file systems and depends on ``tune2fs``. .. _ref-classes-gconf: ``gconf`` ========= The :ref:`ref-classes-gconf` class provides common functionality for recipes that need to install GConf schemas. The schemas will be put into a separate package (``${``\ :term:`PN`\ ``}-gconf``) that is created automatically when this class is inherited. This package uses the appropriate post-install and post-remove (postinst/postrm) scriptlets to register and unregister the schemas in the target image. .. _ref-classes-gettext: ``gettext`` =========== The :ref:`ref-classes-gettext` class provides support for building software that uses the GNU ``gettext`` internationalization and localization system. All recipes building software that use ``gettext`` should inherit this class. .. _ref-classes-github-releases: ``github-releases`` =================== For recipes that fetch release tarballs from github, the :ref:`ref-classes-github-releases` class sets up a standard way for checking available upstream versions (to support ``devtool upgrade`` and the Automated Upgrade Helper (AUH)). To use it, add ":ref:`ref-classes-github-releases`" to the inherit line in the recipe, and if the default value of :term:`GITHUB_BASE_URI` is not suitable, then set your own value in the recipe. You should then use ``${GITHUB_BASE_URI}`` in the value you set for :term:`SRC_URI` within the recipe. .. _ref-classes-gnomebase: ``gnomebase`` ============= The :ref:`ref-classes-gnomebase` class is the base class for recipes that build software from the GNOME stack. This class sets :term:`SRC_URI` to download the source from the GNOME mirrors as well as extending :term:`FILES` with the typical GNOME installation paths. .. _ref-classes-go: ``go`` ====== The :ref:`ref-classes-go` class supports building Go programs. The behavior of this class is controlled by the mandatory :term:`GO_IMPORT` variable, and by the optional :term:`GO_INSTALL` and :term:`GO_INSTALL_FILTEROUT` ones. To build a Go program with the Yocto Project, you can use the :yocto_git:`go-helloworld_0.1.bb ` recipe as an example. .. _ref-classes-go-mod: ``go-mod`` ========== The :ref:`ref-classes-go-mod` class allows to use Go modules, and inherits the :ref:`ref-classes-go` class. See the associated :term:`GO_WORKDIR` variable. .. _ref-classes-gobject-introspection: ``gobject-introspection`` ========================= Provides support for recipes building software that supports GObject introspection. This functionality is only enabled if the "gobject-introspection-data" feature is in :term:`DISTRO_FEATURES` as well as "qemu-usermode" being in :term:`MACHINE_FEATURES`. .. note:: This functionality is :ref:`backfilled ` by default and, if not applicable, should be disabled through :term:`DISTRO_FEATURES_BACKFILL_CONSIDERED` or :term:`MACHINE_FEATURES_BACKFILL_CONSIDERED`, respectively. .. _ref-classes-grub-efi: ``grub-efi`` ============ The :ref:`ref-classes-grub-efi` class provides ``grub-efi``-specific functions for building bootable images. This class supports several variables: - :term:`INITRD`: Indicates list of filesystem images to concatenate and use as an initial RAM disk (initrd) (optional). - :term:`ROOTFS`: Indicates a filesystem image to include as the root filesystem (optional). - :term:`GRUB_GFXSERIAL`: Set this to "1" to have graphics and serial in the boot menu. - :term:`LABELS`: A list of targets for the automatic configuration. - :term:`APPEND`: An override list of append strings for each ``LABEL``. - :term:`GRUB_OPTS`: Additional options to add to the configuration (optional). Options are delimited using semi-colon characters (``;``). - :term:`GRUB_TIMEOUT`: Timeout before executing the default ``LABEL`` (optional). .. _ref-classes-gsettings: ``gsettings`` ============= The :ref:`ref-classes-gsettings` class provides common functionality for recipes that need to install GSettings (glib) schemas. The schemas are assumed to be part of the main package. Appropriate post-install and post-remove (postinst/postrm) scriptlets are added to register and unregister the schemas in the target image. .. _ref-classes-gtk-doc: ``gtk-doc`` =========== The :ref:`ref-classes-gtk-doc` class is a helper class to pull in the appropriate ``gtk-doc`` dependencies and disable ``gtk-doc``. .. _ref-classes-gtk-icon-cache: ``gtk-icon-cache`` ================== The :ref:`ref-classes-gtk-icon-cache` class generates the proper post-install and post-remove (postinst/postrm) scriptlets for packages that use GTK+ and install icons. These scriptlets call ``gtk-update-icon-cache`` to add the fonts to GTK+'s icon cache. Since the cache files are architecture-specific, ``gtk-update-icon-cache`` is run using QEMU if the postinst scriptlets need to be run on the build host during image creation. .. _ref-classes-gtk-immodules-cache: ``gtk-immodules-cache`` ======================= The :ref:`ref-classes-gtk-immodules-cache` class generates the proper post-install and post-remove (postinst/postrm) scriptlets for packages that install GTK+ input method modules for virtual keyboards. These scriptlets call ``gtk-update-icon-cache`` to add the input method modules to the cache. Since the cache files are architecture-specific, ``gtk-update-icon-cache`` is run using QEMU if the postinst scriptlets need to be run on the build host during image creation. If the input method modules being installed are in packages other than the main package, set :term:`GTKIMMODULES_PACKAGES` to specify the packages containing the modules. .. _ref-classes-gzipnative: ``gzipnative`` ============== The :ref:`ref-classes-gzipnative` class enables the use of different native versions of ``gzip`` and ``pigz`` rather than the versions of these tools from the build host. .. _ref-classes-icecc: ``icecc`` ========= The :ref:`ref-classes-icecc` class supports `Icecream `__, which facilitates taking compile jobs and distributing them among remote machines. The class stages directories with symlinks from ``gcc`` and ``g++`` to ``icecc``, for both native and cross compilers. Depending on each configure or compile, the OpenEmbedded build system adds the directories at the head of the ``PATH`` list and then sets the ``ICECC_CXX`` and ``ICECC_CC`` variables, which are the paths to the ``g++`` and ``gcc`` compilers, respectively. For the cross compiler, the class creates a ``tar.gz`` file that contains the Yocto Project toolchain and sets ``ICECC_VERSION``, which is the version of the cross-compiler used in the cross-development toolchain, accordingly. The class handles all three different compile stages (i.e native, cross-kernel and target) and creates the necessary environment ``tar.gz`` file to be used by the remote machines. The class also supports SDK generation. If :term:`ICECC_PATH` is not set in your ``local.conf`` file, then the class tries to locate the ``icecc`` binary using ``which``. If :term:`ICECC_ENV_EXEC` is set in your ``local.conf`` file, the variable should point to the ``icecc-create-env`` script provided by the user. If you do not point to a user-provided script, the build system uses the default script provided by the recipe :oe_git:`icecc-create-env_0.1.bb `. .. note:: This script is a modified version and not the one that comes with ``icecream``. If you do not want the Icecream distributed compile support to apply to specific recipes or classes, you can ask them to be ignored by Icecream by listing the recipes and classes using the :term:`ICECC_RECIPE_DISABLE` and :term:`ICECC_CLASS_DISABLE` variables, respectively, in your ``local.conf`` file. Doing so causes the OpenEmbedded build system to handle these compilations locally. Additionally, you can list recipes using the :term:`ICECC_RECIPE_ENABLE` variable in your ``local.conf`` file to force ``icecc`` to be enabled for recipes using an empty :term:`PARALLEL_MAKE` variable. Inheriting the :ref:`ref-classes-icecc` class changes all sstate signatures. Consequently, if a development team has a dedicated build system that populates :term:`SSTATE_MIRRORS` and they want to reuse sstate from :term:`SSTATE_MIRRORS`, then all developers and the build system need to either inherit the :ref:`ref-classes-icecc` class or nobody should. At the distribution level, you can inherit the :ref:`ref-classes-icecc` class to be sure that all builders start with the same sstate signatures. After inheriting the class, you can then disable the feature by setting the :term:`ICECC_DISABLED` variable to "1" as follows:: INHERIT_DISTRO:append = " icecc" ICECC_DISABLED ??= "1" This practice makes sure everyone is using the same signatures but also requires individuals that do want to use Icecream to enable the feature individually as follows in your ``local.conf`` file:: ICECC_DISABLED = "" .. _ref-classes-image: ``image`` ========= The :ref:`ref-classes-image` class helps support creating images in different formats. First, the root filesystem is created from packages using one of the ``rootfs*.bbclass`` files (depending on the package format used) and then one or more image files are created. - The :term:`IMAGE_FSTYPES` variable controls the types of images to generate. - The :term:`IMAGE_INSTALL` variable controls the list of packages to install into the image. For information on customizing images, see the ":ref:`dev-manual/customizing-images:customizing images`" section in the Yocto Project Development Tasks Manual. For information on how images are created, see the ":ref:`overview-manual/concepts:images`" section in the Yocto Project Overview and Concepts Manual. .. _ref-classes-image-buildinfo: ``image-buildinfo`` =================== The :ref:`ref-classes-image-buildinfo` class writes a plain text file containing build information to the target filesystem at ``${sysconfdir}/buildinfo`` by default (as specified by :term:`IMAGE_BUILDINFO_FILE`). This can be useful for manually determining the origin of any given image. It writes out two sections: #. `Build Configuration`: a list of variables and their values (specified by :term:`IMAGE_BUILDINFO_VARS`, which defaults to :term:`DISTRO` and :term:`DISTRO_VERSION`) #. `Layer Revisions`: the revisions of all of the layers used in the build. Additionally, when building an SDK it will write the same contents to ``/buildinfo`` by default (as specified by :term:`SDK_BUILDINFO_FILE`). .. _ref-classes-image_types: ``image_types`` =============== The :ref:`ref-classes-image_types` class defines all of the standard image output types that you can enable through the :term:`IMAGE_FSTYPES` variable. You can use this class as a reference on how to add support for custom image output types. By default, the :ref:`ref-classes-image` class automatically enables the :ref:`ref-classes-image_types` class. The :ref:`ref-classes-image` class uses the ``IMGCLASSES`` variable as follows:: IMGCLASSES = "rootfs_${IMAGE_PKGTYPE} image_types ${IMAGE_CLASSES}" IMGCLASSES += "${@['populate_sdk_base', 'populate_sdk_ext']['linux' in d.getVar("SDK_OS")]}" IMGCLASSES += "${@bb.utils.contains_any('IMAGE_FSTYPES', 'live iso hddimg', 'image-live', '', d)}" IMGCLASSES += "${@bb.utils.contains('IMAGE_FSTYPES', 'container', 'image-container', '', d)}" IMGCLASSES += "image_types_wic" IMGCLASSES += "rootfs-postcommands" IMGCLASSES += "image-postinst-intercepts" inherit ${IMGCLASSES} The :ref:`ref-classes-image_types` class also handles conversion and compression of images. .. note:: To build a VMware VMDK image, you need to add "wic.vmdk" to :term:`IMAGE_FSTYPES`. This would also be similar for Virtual Box Virtual Disk Image ("vdi") and QEMU Copy On Write Version 2 ("qcow2") images. .. _ref-classes-image-live: ``image-live`` ============== This class controls building "live" (i.e. HDDIMG and ISO) images. Live images contain syslinux for legacy booting, as well as the bootloader specified by :term:`EFI_PROVIDER` if :term:`MACHINE_FEATURES` contains "efi". Normally, you do not use this class directly. Instead, you add "live" to :term:`IMAGE_FSTYPES`. .. _ref-classes-insane: ``insane`` ========== The :ref:`ref-classes-insane` class adds a step to the package generation process so that output quality assurance checks are generated by the OpenEmbedded build system. A range of checks are performed that check the build's output for common problems that show up during runtime. Distribution policy usually dictates whether to include this class. You can configure the sanity checks so that specific test failures either raise a warning or an error message. Typically, failures for new tests generate a warning. Subsequent failures for the same test would then generate an error message once the metadata is in a known and good condition. See the ":doc:`/ref-manual/qa-checks`" Chapter for a list of all the warning and error messages you might encounter using a default configuration. Use the :term:`WARN_QA` and :term:`ERROR_QA` variables to control the behavior of these checks at the global level (i.e. in your custom distro configuration). However, to skip one or more checks in recipes, you should use :term:`INSANE_SKIP`. For example, to skip the check for symbolic link ``.so`` files in the main package of a recipe, add the following to the recipe. You need to realize that the package name override, in this example ``${PN}``, must be used:: INSANE_SKIP:${PN} += "dev-so" Please keep in mind that the QA checks are meant to detect real or potential problems in the packaged output. So exercise caution when disabling these checks. The tests you can list with the :term:`WARN_QA` and :term:`ERROR_QA` variables are: - ``already-stripped:`` Checks that produced binaries have not already been stripped prior to the build system extracting debug symbols. It is common for upstream software projects to default to stripping debug symbols for output binaries. In order for debugging to work on the target using ``-dbg`` packages, this stripping must be disabled. - ``arch:`` Checks the Executable and Linkable Format (ELF) type, bit size, and endianness of any binaries to ensure they match the target architecture. This test fails if any binaries do not match the type since there would be an incompatibility. The test could indicate that the wrong compiler or compiler options have been used. Sometimes software, like bootloaders, might need to bypass this check. - ``buildpaths:`` Checks for paths to locations on the build host inside the output files. Not only can these leak information about the build environment, they also hinder binary reproducibility. - ``build-deps:`` Determines if a build-time dependency that is specified through :term:`DEPENDS`, explicit :term:`RDEPENDS`, or task-level dependencies exists to match any runtime dependency. This determination is particularly useful to discover where runtime dependencies are detected and added during packaging. If no explicit dependency has been specified within the metadata, at the packaging stage it is too late to ensure that the dependency is built, and thus you can end up with an error when the package is installed into the image during the :ref:`ref-tasks-rootfs` task because the auto-detected dependency was not satisfied. An example of this would be where the :ref:`ref-classes-update-rc.d` class automatically adds a dependency on the ``initscripts-functions`` package to packages that install an initscript that refers to ``/etc/init.d/functions``. The recipe should really have an explicit :term:`RDEPENDS` for the package in question on ``initscripts-functions`` so that the OpenEmbedded build system is able to ensure that the ``initscripts`` recipe is actually built and thus the ``initscripts-functions`` package is made available. - ``configure-gettext:`` Checks that if a recipe is building something that uses automake and the automake files contain an ``AM_GNU_GETTEXT`` directive, that the recipe also inherits the :ref:`ref-classes-gettext` class to ensure that gettext is available during the build. - ``compile-host-path:`` Checks the :ref:`ref-tasks-compile` log for indications that paths to locations on the build host were used. Using such paths might result in host contamination of the build output. - ``debug-deps:`` Checks that all packages except ``-dbg`` packages do not depend on ``-dbg`` packages, which would cause a packaging bug. - ``debug-files:`` Checks for ``.debug`` directories in anything but the ``-dbg`` package. The debug files should all be in the ``-dbg`` package. Thus, anything packaged elsewhere is incorrect packaging. - ``dep-cmp:`` Checks for invalid version comparison statements in runtime dependency relationships between packages (i.e. in :term:`RDEPENDS`, :term:`RRECOMMENDS`, :term:`RSUGGESTS`, :term:`RPROVIDES`, :term:`RREPLACES`, and :term:`RCONFLICTS` variable values). Any invalid comparisons might trigger failures or undesirable behavior when passed to the package manager. - ``desktop:`` Runs the ``desktop-file-validate`` program against any ``.desktop`` files to validate their contents against the specification for ``.desktop`` files. - ``dev-deps:`` Checks that all packages except ``-dev`` or ``-staticdev`` packages do not depend on ``-dev`` packages, which would be a packaging bug. - ``dev-so:`` Checks that the ``.so`` symbolic links are in the ``-dev`` package and not in any of the other packages. In general, these symlinks are only useful for development purposes. Thus, the ``-dev`` package is the correct location for them. In very rare cases, such as dynamically loaded modules, these symlinks are needed instead in the main package. - ``empty-dirs:`` Checks that packages are not installing files to directories that are normally expected to be empty (such as ``/tmp``) The list of directories that are checked is specified by the :term:`QA_EMPTY_DIRS` variable. - ``file-rdeps:`` Checks that file-level dependencies identified by the OpenEmbedded build system at packaging time are satisfied. For example, a shell script might start with the line ``#!/bin/bash``. This line would translate to a file dependency on ``/bin/bash``. Of the three package managers that the OpenEmbedded build system supports, only RPM directly handles file-level dependencies, resolving them automatically to packages providing the files. However, the lack of that functionality in the other two package managers does not mean the dependencies do not still need resolving. This QA check attempts to ensure that explicitly declared :term:`RDEPENDS` exist to handle any file-level dependency detected in packaged files. - ``files-invalid:`` Checks for :term:`FILES` variable values that contain "//", which is invalid. - ``host-user-contaminated:`` Checks that no package produced by the recipe contains any files outside of ``/home`` with a user or group ID that matches the user running BitBake. A match usually indicates that the files are being installed with an incorrect UID/GID, since target IDs are independent from host IDs. For additional information, see the section describing the :ref:`ref-tasks-install` task. - ``incompatible-license:`` Report when packages are excluded from being created due to being marked with a license that is in :term:`INCOMPATIBLE_LICENSE`. - ``install-host-path:`` Checks the :ref:`ref-tasks-install` log for indications that paths to locations on the build host were used. Using such paths might result in host contamination of the build output. - ``installed-vs-shipped:`` Reports when files have been installed within :ref:`ref-tasks-install` but have not been included in any package by way of the :term:`FILES` variable. Files that do not appear in any package cannot be present in an image later on in the build process. Ideally, all installed files should be packaged or not installed at all. These files can be deleted at the end of :ref:`ref-tasks-install` if the files are not needed in any package. - ``invalid-chars:`` Checks that the recipe metadata variables :term:`DESCRIPTION`, :term:`SUMMARY`, :term:`LICENSE`, and :term:`SECTION` do not contain non-UTF-8 characters. Some package managers do not support such characters. - ``invalid-packageconfig:`` Checks that no undefined features are being added to :term:`PACKAGECONFIG`. For example, any name "foo" for which the following form does not exist:: PACKAGECONFIG[foo] = "..." - ``la:`` Checks ``.la`` files for any :term:`TMPDIR` paths. Any ``.la`` file containing these paths is incorrect since ``libtool`` adds the correct sysroot prefix when using the files automatically itself. - ``ldflags:`` Ensures that the binaries were linked with the :term:`LDFLAGS` options provided by the build system. If this test fails, check that the :term:`LDFLAGS` variable is being passed to the linker command. - ``libdir:`` Checks for libraries being installed into incorrect (possibly hardcoded) installation paths. For example, this test will catch recipes that install ``/lib/bar.so`` when ``${base_libdir}`` is "lib32". Another example is when recipes install ``/usr/lib64/foo.so`` when ``${libdir}`` is "/usr/lib". - ``libexec:`` Checks if a package contains files in ``/usr/libexec``. This check is not performed if the ``libexecdir`` variable has been set explicitly to ``/usr/libexec``. - ``mime:`` Check that if a package contains mime type files (``.xml`` files in ``${datadir}/mime/packages``) that the recipe also inherits the :ref:`ref-classes-mime` class in order to ensure that these get properly installed. - ``mime-xdg:`` Checks that if a package contains a .desktop file with a 'MimeType' key present, that the recipe inherits the :ref:`ref-classes-mime-xdg` class that is required in order for that to be activated. - ``missing-update-alternatives:`` Check that if a recipe sets the :term:`ALTERNATIVE` variable that the recipe also inherits :ref:`ref-classes-update-alternatives` such that the alternative will be correctly set up. - ``packages-list:`` Checks for the same package being listed multiple times through the :term:`PACKAGES` variable value. Installing the package in this manner can cause errors during packaging. - ``patch-fuzz:`` Checks for fuzz in patch files that may allow them to apply incorrectly if the underlying code changes. - ``patch-status-core:`` Checks that the Upstream-Status is specified and valid in the headers of patches for recipes in the OE-Core layer. - ``patch-status-noncore:`` Checks that the Upstream-Status is specified and valid in the headers of patches for recipes in layers other than OE-Core. - ``perllocalpod:`` Checks for ``perllocal.pod`` being erroneously installed and packaged by a recipe. - ``perm-config:`` Reports lines in ``fs-perms.txt`` that have an invalid format. - ``perm-line:`` Reports lines in ``fs-perms.txt`` that have an invalid format. - ``perm-link:`` Reports lines in ``fs-perms.txt`` that specify 'link' where the specified target already exists. - ``perms:`` Currently, this check is unused but reserved. - ``pkgconfig:`` Checks ``.pc`` files for any :term:`TMPDIR`/:term:`WORKDIR` paths. Any ``.pc`` file containing these paths is incorrect since ``pkg-config`` itself adds the correct sysroot prefix when the files are accessed. - ``pkgname:`` Checks that all packages in :term:`PACKAGES` have names that do not contain invalid characters (i.e. characters other than 0-9, a-z, ., +, and -). - ``pkgv-undefined:`` Checks to see if the :term:`PKGV` variable is undefined during :ref:`ref-tasks-package`. - ``pkgvarcheck:`` Checks through the variables :term:`RDEPENDS`, :term:`RRECOMMENDS`, :term:`RSUGGESTS`, :term:`RCONFLICTS`, :term:`RPROVIDES`, :term:`RREPLACES`, :term:`FILES`, :term:`ALLOW_EMPTY`, ``pkg_preinst``, ``pkg_postinst``, ``pkg_prerm`` and ``pkg_postrm``, and reports if there are variable sets that are not package-specific. Using these variables without a package suffix is bad practice, and might unnecessarily complicate dependencies of other packages within the same recipe or have other unintended consequences. - ``pn-overrides:`` Checks that a recipe does not have a name (:term:`PN`) value that appears in :term:`OVERRIDES`. If a recipe is named such that its :term:`PN` value matches something already in :term:`OVERRIDES` (e.g. :term:`PN` happens to be the same as :term:`MACHINE` or :term:`DISTRO`), it can have unexpected consequences. For example, assignments such as ``FILES:${PN} = "xyz"`` effectively turn into ``FILES = "xyz"``. - ``rpaths:`` Checks for rpaths in the binaries that contain build system paths such as :term:`TMPDIR`. If this test fails, bad ``-rpath`` options are being passed to the linker commands and your binaries have potential security issues. - ``shebang-size:`` Check that the shebang line (``#!`` in the first line) in a packaged script is not longer than 128 characters, which can cause an error at runtime depending on the operating system. - ``split-strip:`` Reports that splitting or stripping debug symbols from binaries has failed. - ``staticdev:`` Checks for static library files (``*.a``) in non-``staticdev`` packages. - ``src-uri-bad:`` Checks that the :term:`SRC_URI` value set by a recipe does not contain a reference to ``${PN}`` (instead of the correct ``${BPN}``) nor refers to unstable Github archive tarballs. - ``symlink-to-sysroot:`` Checks for symlinks in packages that point into :term:`TMPDIR` on the host. Such symlinks will work on the host, but are clearly invalid when running on the target. - ``textrel:`` Checks for ELF binaries that contain relocations in their ``.text`` sections, which can result in a performance impact at runtime. See the explanation for the ``ELF binary`` message in ":doc:`/ref-manual/qa-checks`" for more information regarding runtime performance issues. - ``unhandled-features-check:`` check that if one of the variables that the :ref:`ref-classes-features_check` class supports (e.g. :term:`REQUIRED_DISTRO_FEATURES`) is set by a recipe, then the recipe also inherits :ref:`ref-classes-features_check` in order for the requirement to actually work. - ``unimplemented-ptest:`` Checks that ptests are implemented for upstream tests. - ``unlisted-pkg-lics:`` Checks that all declared licenses applying for a package are also declared on the recipe level (i.e. any license in ``LICENSE:*`` should appear in :term:`LICENSE`). - ``useless-rpaths:`` Checks for dynamic library load paths (rpaths) in the binaries that by default on a standard system are searched by the linker (e.g. ``/lib`` and ``/usr/lib``). While these paths will not cause any breakage, they do waste space and are unnecessary. - ``usrmerge:`` If ``usrmerge`` is in :term:`DISTRO_FEATURES`, this check will ensure that no package installs files to root (``/bin``, ``/sbin``, ``/lib``, ``/lib64``) directories. - ``var-undefined:`` Reports when variables fundamental to packaging (i.e. :term:`WORKDIR`, :term:`DEPLOY_DIR`, :term:`D`, :term:`PN`, and :term:`PKGD`) are undefined during :ref:`ref-tasks-package`. - ``version-going-backwards:`` If the :ref:`ref-classes-buildhistory` class is enabled, reports when a package being written out has a lower version than the previously written package under the same name. If you are placing output packages into a feed and upgrading packages on a target system using that feed, the version of a package going backwards can result in the target system not correctly upgrading to the "new" version of the package. .. note:: This is only relevant when you are using runtime package management on your target system. - ``xorg-driver-abi:`` Checks that all packages containing Xorg drivers have ABI dependencies. The ``xserver-xorg`` recipe provides driver ABI names. All drivers should depend on the ABI versions that they have been built against. Driver recipes that include ``xorg-driver-input.inc`` or ``xorg-driver-video.inc`` will automatically get these versions. Consequently, you should only need to explicitly add dependencies to binary driver recipes. .. _ref-classes-kernel: ``kernel`` ========== The :ref:`ref-classes-kernel` class handles building Linux kernels. The class contains code to build all kernel trees. All needed headers are staged into the :term:`STAGING_KERNEL_DIR` directory to allow out-of-tree module builds using the :ref:`ref-classes-module` class. If a file named ``defconfig`` is listed in :term:`SRC_URI`, then by default :ref:`ref-tasks-configure` copies it as ``.config`` in the build directory, so it is automatically used as the kernel configuration for the build. This copy is not performed in case ``.config`` already exists there: this allows recipes to produce a configuration by other means in ``do_configure:prepend``. Each built kernel module is packaged separately and inter-module dependencies are created by parsing the ``modinfo`` output. If all modules are required, then installing the ``kernel-modules`` package installs all packages with modules and various other kernel packages such as ``kernel-vmlinux``. The :ref:`ref-classes-kernel` class contains logic that allows you to embed an initial RAM filesystem (:term:`Initramfs`) image when you build the kernel image. For information on how to build an :term:`Initramfs`, see the ":ref:`dev-manual/building:building an initial ram filesystem (Initramfs) image`" section in the Yocto Project Development Tasks Manual. Various other classes are used by the :ref:`ref-classes-kernel` and :ref:`ref-classes-module` classes internally including the :ref:`ref-classes-kernel-arch`, :ref:`ref-classes-module-base`, and :ref:`ref-classes-linux-kernel-base` classes. .. _ref-classes-kernel-arch: ``kernel-arch`` =============== The :ref:`ref-classes-kernel-arch` class sets the ``ARCH`` environment variable for Linux kernel compilation (including modules). .. _ref-classes-kernel-devicetree: ``kernel-devicetree`` ===================== The :ref:`ref-classes-kernel-devicetree` class, which is inherited by the :ref:`ref-classes-kernel` class, supports device tree generation. Its behavior is mainly controlled by the following variables: - :term:`KERNEL_DEVICETREE_BUNDLE`: whether to bundle the kernel and device tree - :term:`KERNEL_DTBDEST`: directory where to install DTB files - :term:`KERNEL_DTBVENDORED`: whether to keep vendor subdirectories - :term:`KERNEL_DTC_FLAGS`: flags for ``dtc``, the Device Tree Compiler - :term:`KERNEL_PACKAGE_NAME`: base name of the kernel packages .. _ref-classes-kernel-fitimage: ``kernel-fitimage`` =================== The :ref:`ref-classes-kernel-fitimage` class provides support to pack a kernel image, device trees, a U-boot script, an :term:`Initramfs` bundle and a RAM disk into a single FIT image. In theory, a FIT image can support any number of kernels, U-boot scripts, :term:`Initramfs` bundles, RAM disks and device-trees. However, :ref:`ref-classes-kernel-fitimage` currently only supports limited usecases: just one kernel image, an optional U-boot script, an optional :term:`Initramfs` bundle, an optional RAM disk, and any number of device trees. To create a FIT image, it is required that :term:`KERNEL_CLASSES` is set to include ":ref:`ref-classes-kernel-fitimage`" and one of :term:`KERNEL_IMAGETYPE`, :term:`KERNEL_ALT_IMAGETYPE` or :term:`KERNEL_IMAGETYPES` to include "fitImage". The options for the device tree compiler passed to ``mkimage -D`` when creating the FIT image are specified using the :term:`UBOOT_MKIMAGE_DTCOPTS` variable. Only a single kernel can be added to the FIT image created by :ref:`ref-classes-kernel-fitimage` and the kernel image in FIT is mandatory. The address where the kernel image is to be loaded by U-Boot is specified by :term:`UBOOT_LOADADDRESS` and the entrypoint by :term:`UBOOT_ENTRYPOINT`. Setting :term:`FIT_ADDRESS_CELLS` to "2" is necessary if such addresses are 64 bit ones. Multiple device trees can be added to the FIT image created by :ref:`ref-classes-kernel-fitimage` and the device tree is optional. The address where the device tree is to be loaded by U-Boot is specified by :term:`UBOOT_DTBO_LOADADDRESS` for device tree overlays and by :term:`UBOOT_DTB_LOADADDRESS` for device tree binaries. Only a single RAM disk can be added to the FIT image created by :ref:`ref-classes-kernel-fitimage` and the RAM disk in FIT is optional. The address where the RAM disk image is to be loaded by U-Boot is specified by :term:`UBOOT_RD_LOADADDRESS` and the entrypoint by :term:`UBOOT_RD_ENTRYPOINT`. The ramdisk is added to the FIT image when :term:`INITRAMFS_IMAGE` is specified and requires that :term:`INITRAMFS_IMAGE_BUNDLE` is not set to 1. Only a single :term:`Initramfs` bundle can be added to the FIT image created by :ref:`ref-classes-kernel-fitimage` and the :term:`Initramfs` bundle in FIT is optional. In case of :term:`Initramfs`, the kernel is configured to be bundled with the root filesystem in the same binary (example: zImage-initramfs-:term:`MACHINE`.bin). When the kernel is copied to RAM and executed, it unpacks the :term:`Initramfs` root filesystem. The :term:`Initramfs` bundle can be enabled when :term:`INITRAMFS_IMAGE` is specified and requires that :term:`INITRAMFS_IMAGE_BUNDLE` is set to 1. The address where the :term:`Initramfs` bundle is to be loaded by U-boot is specified by :term:`UBOOT_LOADADDRESS` and the entrypoint by :term:`UBOOT_ENTRYPOINT`. Only a single U-boot boot script can be added to the FIT image created by :ref:`ref-classes-kernel-fitimage` and the boot script is optional. The boot script is specified in the ITS file as a text file containing U-boot commands. When using a boot script the user should configure the U-boot :ref:`ref-tasks-install` task to copy the script to sysroot. So the script can be included in the FIT image by the :ref:`ref-classes-kernel-fitimage` class. At run-time, U-boot CONFIG_BOOTCOMMAND define can be configured to load the boot script from the FIT image and execute it. The FIT image generated by the :ref:`ref-classes-kernel-fitimage` class is signed when the variables :term:`UBOOT_SIGN_ENABLE`, :term:`UBOOT_MKIMAGE_DTCOPTS`, :term:`UBOOT_SIGN_KEYDIR` and :term:`UBOOT_SIGN_KEYNAME` are set appropriately. The default values used for :term:`FIT_HASH_ALG` and :term:`FIT_SIGN_ALG` in :ref:`ref-classes-kernel-fitimage` are "sha256" and "rsa2048" respectively. The keys for signing the FIT image can be generated using the :ref:`ref-classes-kernel-fitimage` class when both :term:`FIT_GENERATE_KEYS` and :term:`UBOOT_SIGN_ENABLE` are set to "1". .. _ref-classes-kernel-grub: ``kernel-grub`` =============== The :ref:`ref-classes-kernel-grub` class updates the boot area and the boot menu with the kernel as the priority boot mechanism while installing a RPM to update the kernel on a deployed target. .. _ref-classes-kernel-module-split: ``kernel-module-split`` ======================= The :ref:`ref-classes-kernel-module-split` class provides common functionality for splitting Linux kernel modules into separate packages. .. _ref-classes-kernel-uboot: ``kernel-uboot`` ================ The :ref:`ref-classes-kernel-uboot` class provides support for building from vmlinux-style kernel sources. .. _ref-classes-kernel-uimage: ``kernel-uimage`` ================= The :ref:`ref-classes-kernel-uimage` class provides support to pack uImage. .. _ref-classes-kernel-yocto: ``kernel-yocto`` ================ The :ref:`ref-classes-kernel-yocto` class provides common functionality for building from linux-yocto style kernel source repositories. .. _ref-classes-kernelsrc: ``kernelsrc`` ============= The :ref:`ref-classes-kernelsrc` class sets the Linux kernel source and version. .. _ref-classes-lib_package: ``lib_package`` =============== The :ref:`ref-classes-lib_package` class supports recipes that build libraries and produce executable binaries, where those binaries should not be installed by default along with the library. Instead, the binaries are added to a separate ``${``\ :term:`PN`\ ``}-bin`` package to make their installation optional. .. _ref-classes-libc*: ``libc*`` ========= The :ref:`ref-classes-libc*` classes support recipes that build packages with ``libc``: - The :ref:`libc-common ` class provides common support for building with ``libc``. - The :ref:`libc-package ` class supports packaging up ``glibc`` and ``eglibc``. .. _ref-classes-license: ``license`` =========== The :ref:`ref-classes-license` class provides license manifest creation and license exclusion. This class is enabled by default using the default value for the :term:`INHERIT_DISTRO` variable. .. _ref-classes-linux-kernel-base: ``linux-kernel-base`` ===================== The :ref:`ref-classes-linux-kernel-base` class provides common functionality for recipes that build out of the Linux kernel source tree. These builds goes beyond the kernel itself. For example, the Perf recipe also inherits this class. .. _ref-classes-linuxloader: ``linuxloader`` =============== Provides the function ``linuxloader()``, which gives the value of the dynamic loader/linker provided on the platform. This value is used by a number of other classes. .. _ref-classes-logging: ``logging`` =========== The :ref:`ref-classes-logging` class provides the standard shell functions used to log messages for various BitBake severity levels (i.e. ``bbplain``, ``bbnote``, ``bbwarn``, ``bberror``, ``bbfatal``, and ``bbdebug``). This class is enabled by default since it is inherited by the :ref:`ref-classes-base` class. .. _ref-classes-meson: ``meson`` ========= The :ref:`ref-classes-meson` class allows to create recipes that build software using the `Meson `__ build system. You can use the :term:`MESON_BUILDTYPE`, :term:`MESON_TARGET` and :term:`EXTRA_OEMESON` variables to specify additional configuration options to be passed using the ``meson`` command line. .. _ref-classes-metadata_scm: ``metadata_scm`` ================ The :ref:`ref-classes-metadata_scm` class provides functionality for querying the branch and revision of a Source Code Manager (SCM) repository. The :ref:`ref-classes-base` class uses this class to print the revisions of each layer before starting every build. The :ref:`ref-classes-metadata_scm` class is enabled by default because it is inherited by the :ref:`ref-classes-base` class. .. _ref-classes-migrate_localcount: ``migrate_localcount`` ====================== The :ref:`ref-classes-migrate_localcount` class verifies a recipe's localcount data and increments it appropriately. .. _ref-classes-mime: ``mime`` ======== The :ref:`ref-classes-mime` class generates the proper post-install and post-remove (postinst/postrm) scriptlets for packages that install MIME type files. These scriptlets call ``update-mime-database`` to add the MIME types to the shared database. .. _ref-classes-mime-xdg: ``mime-xdg`` ============ The :ref:`ref-classes-mime-xdg` class generates the proper post-install and post-remove (postinst/postrm) scriptlets for packages that install ``.desktop`` files containing ``MimeType`` entries. These scriptlets call ``update-desktop-database`` to add the MIME types to the database of MIME types handled by desktop files. Thanks to this class, when users open a file through a file browser on recently created images, they don't have to choose the application to open the file from the pool of all known applications, even the ones that cannot open the selected file. If you have recipes installing their ``.desktop`` files as absolute symbolic links, the detection of such files cannot be done by the current implementation of this class. In this case, you have to add the corresponding package names to the :term:`MIME_XDG_PACKAGES` variable. .. _ref-classes-mirrors: ``mirrors`` =========== The :ref:`ref-classes-mirrors` class sets up some standard :term:`MIRRORS` entries for source code mirrors. These mirrors provide a fall-back path in case the upstream source specified in :term:`SRC_URI` within recipes is unavailable. This class is enabled by default since it is inherited by the :ref:`ref-classes-base` class. .. _ref-classes-module: ``module`` ========== The :ref:`ref-classes-module` class provides support for building out-of-tree Linux kernel modules. The class inherits the :ref:`ref-classes-module-base` and :ref:`ref-classes-kernel-module-split` classes, and implements the :ref:`ref-tasks-compile` and :ref:`ref-tasks-install` tasks. The class provides everything needed to build and package a kernel module. For general information on out-of-tree Linux kernel modules, see the ":ref:`kernel-dev/common:incorporating out-of-tree modules`" section in the Yocto Project Linux Kernel Development Manual. .. _ref-classes-module-base: ``module-base`` =============== The :ref:`ref-classes-module-base` class provides the base functionality for building Linux kernel modules. Typically, a recipe that builds software that includes one or more kernel modules and has its own means of building the module inherits this class as opposed to inheriting the :ref:`ref-classes-module` class. .. _ref-classes-multilib*: ``multilib*`` ============= The :ref:`ref-classes-multilib*` classes provide support for building libraries with different target optimizations or target architectures and installing them side-by-side in the same image. For more information on using the Multilib feature, see the ":ref:`dev-manual/libraries:combining multiple versions of library files into one image`" section in the Yocto Project Development Tasks Manual. .. _ref-classes-native: ``native`` ========== The :ref:`ref-classes-native` class provides common functionality for recipes that build tools to run on the :term:`Build Host` (i.e. tools that use the compiler or other tools from the build host). You can create a recipe that builds tools that run natively on the host a couple different ways: - Create a ``myrecipe-native.bb`` recipe that inherits the :ref:`ref-classes-native` class. If you use this method, you must order the inherit statement in the recipe after all other inherit statements so that the :ref:`ref-classes-native` class is inherited last. .. note:: When creating a recipe this way, the recipe name must follow this naming convention:: myrecipe-native.bb Not using this naming convention can lead to subtle problems caused by existing code that depends on that naming convention. - Create or modify a target recipe that contains the following:: BBCLASSEXTEND = "native" Inside the recipe, use ``:class-native`` and ``:class-target`` overrides to specify any functionality specific to the respective native or target case. Although applied differently, the :ref:`ref-classes-native` class is used with both methods. The advantage of the second method is that you do not need to have two separate recipes (assuming you need both) for native and target. All common parts of the recipe are automatically shared. .. _ref-classes-nativesdk: ``nativesdk`` ============= The :ref:`ref-classes-nativesdk` class provides common functionality for recipes that wish to build tools to run as part of an SDK (i.e. tools that run on :term:`SDKMACHINE`). You can create a recipe that builds tools that run on the SDK machine a couple different ways: - Create a ``nativesdk-myrecipe.bb`` recipe that inherits the :ref:`ref-classes-nativesdk` class. If you use this method, you must order the inherit statement in the recipe after all other inherit statements so that the :ref:`ref-classes-nativesdk` class is inherited last. - Create a :ref:`ref-classes-nativesdk` variant of any recipe by adding the following:: BBCLASSEXTEND = "nativesdk" Inside the recipe, use ``:class-nativesdk`` and ``:class-target`` overrides to specify any functionality specific to the respective SDK machine or target case. .. note:: When creating a recipe, you must follow this naming convention:: nativesdk-myrecipe.bb Not doing so can lead to subtle problems because there is code that depends on the naming convention. Although applied differently, the :ref:`ref-classes-nativesdk` class is used with both methods. The advantage of the second method is that you do not need to have two separate recipes (assuming you need both) for the SDK machine and the target. All common parts of the recipe are automatically shared. .. _ref-classes-nopackages: ``nopackages`` ============== Disables packaging tasks for those recipes and classes where packaging is not needed. .. _ref-classes-npm: ``npm`` ======= Provides support for building Node.js software fetched using the :wikipedia:`node package manager (NPM) `. .. note:: Currently, recipes inheriting this class must use the ``npm://`` fetcher to have dependencies fetched and packaged automatically. For information on how to create NPM packages, see the ":ref:`dev-manual/packages:creating node package manager (npm) packages`" section in the Yocto Project Development Tasks Manual. .. _ref-classes-oelint: ``oelint`` ========== The :ref:`ref-classes-oelint` class is an obsolete lint checking tool available in ``meta/classes`` in the :term:`Source Directory`. There are some classes that could be generally useful in OE-Core but are never actually used within OE-Core itself. The :ref:`ref-classes-oelint` class is one such example. However, being aware of this class can reduce the proliferation of different versions of similar classes across multiple layers. .. _ref-classes-overlayfs: ``overlayfs`` ============= It's often desired in Embedded System design to have a read-only root filesystem. But a lot of different applications might want to have read-write access to some parts of a filesystem. It can be especially useful when your update mechanism overwrites the whole root filesystem, but you may want your application data to be preserved between updates. The :ref:`ref-classes-overlayfs` class provides a way to achieve that by means of ``overlayfs`` and at the same time keeping the base root filesystem read-only. To use this class, set a mount point for a partition ``overlayfs`` is going to use as upper layer in your machine configuration. The underlying file system can be anything that is supported by ``overlayfs``. This has to be done in your machine configuration:: OVERLAYFS_MOUNT_POINT[data] = "/data" .. note:: * QA checks fail to catch file existence if you redefine this variable in your recipe! * Only the existence of the systemd mount unit file is checked, not its contents. * To get more details on ``overlayfs``, its internals and supported operations, please refer to the official documentation of the `Linux kernel `__. The class assumes you have a ``data.mount`` systemd unit defined elsewhere in your BSP (e.g. in ``systemd-machine-units`` recipe) and it's installed into the image. Then you can specify writable directories on a recipe basis (e.g. in my-application.bb):: OVERLAYFS_WRITABLE_PATHS[data] = "/usr/share/my-custom-application" To support several mount points you can use a different variable flag. Assuming we want to have a writable location on the file system, but do not need that the data survives a reboot, then we could have a ``mnt-overlay.mount`` unit for a ``tmpfs`` file system. In your machine configuration:: OVERLAYFS_MOUNT_POINT[mnt-overlay] = "/mnt/overlay" and then in your recipe:: OVERLAYFS_WRITABLE_PATHS[mnt-overlay] = "/usr/share/another-application" On a practical note, your application recipe might require multiple overlays to be mounted before running to avoid writing to the underlying file system (which can be forbidden in case of read-only file system) To achieve that :ref:`ref-classes-overlayfs` provides a ``systemd`` helper service for mounting overlays. This helper service is named ``${PN}-overlays.service`` and can be depended on in your application recipe (named ``application`` in the following example) ``systemd`` unit by adding to the unit the following:: [Unit] After=application-overlays.service Requires=application-overlays.service .. note:: The class does not support the ``/etc`` directory itself, because ``systemd`` depends on it. In order to get ``/etc`` in overlayfs, see :ref:`ref-classes-overlayfs-etc`. .. _ref-classes-overlayfs-etc: ``overlayfs-etc`` ================= In order to have the ``/etc`` directory in overlayfs a special handling at early boot stage is required. The idea is to supply a custom init script that mounts ``/etc`` before launching the actual init program, because the latter already requires ``/etc`` to be mounted. Example usage in image recipe:: IMAGE_FEATURES += "overlayfs-etc" .. note:: This class must not be inherited directly. Use :term:`IMAGE_FEATURES` or :term:`EXTRA_IMAGE_FEATURES` Your machine configuration should define at least the device, mount point, and file system type you are going to use for ``overlayfs``:: OVERLAYFS_ETC_MOUNT_POINT = "/data" OVERLAYFS_ETC_DEVICE = "/dev/mmcblk0p2" OVERLAYFS_ETC_FSTYPE ?= "ext4" To control more mount options you should consider setting mount options (``defaults`` is used by default):: OVERLAYFS_ETC_MOUNT_OPTIONS = "wsync" The class provides two options for ``/sbin/init`` generation: - The default option is to rename the original ``/sbin/init`` to ``/sbin/init.orig`` and place the generated init under original name, i.e. ``/sbin/init``. It has an advantage that you won't need to change any kernel parameters in order to make it work, but it poses a restriction that package-management can't be used, because updating the init manager would remove the generated script. - If you wish to keep original init as is, you can set:: OVERLAYFS_ETC_USE_ORIG_INIT_NAME = "0" Then the generated init will be named ``/sbin/preinit`` and you would need to extend your kernel parameters manually in your bootloader configuration. .. _ref-classes-own-mirrors: ``own-mirrors`` =============== The :ref:`ref-classes-own-mirrors` class makes it easier to set up your own :term:`PREMIRRORS` from which to first fetch source before attempting to fetch it from the upstream specified in :term:`SRC_URI` within each recipe. To use this class, inherit it globally and specify :term:`SOURCE_MIRROR_URL`. Here is an example:: INHERIT += "own-mirrors" SOURCE_MIRROR_URL = "http://example.com/my-source-mirror" You can specify only a single URL in :term:`SOURCE_MIRROR_URL`. .. _ref-classes-package: ``package`` =========== The :ref:`ref-classes-package` class supports generating packages from a build's output. The core generic functionality is in ``package.bbclass``. The code specific to particular package types resides in these package-specific classes: :ref:`ref-classes-package_deb`, :ref:`ref-classes-package_rpm`, :ref:`ref-classes-package_ipk`. You can control the list of resulting package formats by using the :term:`PACKAGE_CLASSES` variable defined in your ``conf/local.conf`` configuration file, which is located in the :term:`Build Directory`. When defining the variable, you can specify one or more package types. Since images are generated from packages, a packaging class is needed to enable image generation. The first class listed in this variable is used for image generation. If you take the optional step to set up a repository (package feed) on the development host that can be used by DNF, you can install packages from the feed while you are running the image on the target (i.e. runtime installation of packages). For more information, see the ":ref:`dev-manual/packages:using runtime package management`" section in the Yocto Project Development Tasks Manual. The package-specific class you choose can affect build-time performance and has space ramifications. In general, building a package with IPK takes about thirty percent less time as compared to using RPM to build the same or similar package. This comparison takes into account a complete build of the package with all dependencies previously built. The reason for this discrepancy is because the RPM package manager creates and processes more :term:`Metadata` than the IPK package manager. Consequently, you might consider setting :term:`PACKAGE_CLASSES` to ":ref:`ref-classes-package_ipk`" if you are building smaller systems. Before making your package manager decision, however, you should consider some further things about using RPM: - RPM starts to provide more abilities than IPK due to the fact that it processes more Metadata. For example, this information includes individual file types, file checksum generation and evaluation on install, sparse file support, conflict detection and resolution for Multilib systems, ACID style upgrade, and repackaging abilities for rollbacks. - For smaller systems, the extra space used for the Berkeley Database and the amount of metadata when using RPM can affect your ability to perform on-device upgrades. You can find additional information on the effects of the package class at these two Yocto Project mailing list links: - :yocto_lists:`/pipermail/poky/2011-May/006362.html` - :yocto_lists:`/pipermail/poky/2011-May/006363.html` .. _ref-classes-package_deb: ``package_deb`` =============== The :ref:`ref-classes-package_deb` class provides support for creating packages that use the Debian (i.e. ``.deb``) file format. The class ensures the packages are written out in a ``.deb`` file format to the ``${``\ :term:`DEPLOY_DIR_DEB`\ ``}`` directory. This class inherits the :ref:`ref-classes-package` class and is enabled through the :term:`PACKAGE_CLASSES` variable in the ``local.conf`` file. .. _ref-classes-package_ipk: ``package_ipk`` =============== The :ref:`ref-classes-package_ipk` class provides support for creating packages that use the IPK (i.e. ``.ipk``) file format. The class ensures the packages are written out in a ``.ipk`` file format to the ``${``\ :term:`DEPLOY_DIR_IPK`\ ``}`` directory. This class inherits the :ref:`ref-classes-package` class and is enabled through the :term:`PACKAGE_CLASSES` variable in the ``local.conf`` file. .. _ref-classes-package_rpm: ``package_rpm`` =============== The :ref:`ref-classes-package_rpm` class provides support for creating packages that use the RPM (i.e. ``.rpm``) file format. The class ensures the packages are written out in a ``.rpm`` file format to the ``${``\ :term:`DEPLOY_DIR_RPM`\ ``}`` directory. This class inherits the :ref:`ref-classes-package` class and is enabled through the :term:`PACKAGE_CLASSES` variable in the ``local.conf`` file. .. _ref-classes-packagedata: ``packagedata`` =============== The :ref:`ref-classes-packagedata` class provides common functionality for reading ``pkgdata`` files found in :term:`PKGDATA_DIR`. These files contain information about each output package produced by the OpenEmbedded build system. This class is enabled by default because it is inherited by the :ref:`ref-classes-package` class. .. _ref-classes-packagegroup: ``packagegroup`` ================ The :ref:`ref-classes-packagegroup` class sets default values appropriate for package group recipes (e.g. :term:`PACKAGES`, :term:`PACKAGE_ARCH`, :term:`ALLOW_EMPTY`, and so forth). It is highly recommended that all package group recipes inherit this class. For information on how to use this class, see the ":ref:`dev-manual/customizing-images:customizing images using custom package groups`" section in the Yocto Project Development Tasks Manual. Previously, this class was called the ``task`` class. .. _ref-classes-patch: ``patch`` ========= The :ref:`ref-classes-patch` class provides all functionality for applying patches during the :ref:`ref-tasks-patch` task. This class is enabled by default because it is inherited by the :ref:`ref-classes-base` class. .. _ref-classes-perlnative: ``perlnative`` ============== When inherited by a recipe, the :ref:`ref-classes-perlnative` class supports using the native version of Perl built by the build system rather than using the version provided by the build host. .. _ref-classes-pypi: ``pypi`` ======== The :ref:`ref-classes-pypi` class sets variables appropriately for recipes that build Python modules from `PyPI `__, the Python Package Index. By default it determines the PyPI package name based upon :term:`BPN` (stripping the "python-" or "python3-" prefix off if present), however in some cases you may need to set it manually in the recipe by setting :term:`PYPI_PACKAGE`. Variables set by the :ref:`ref-classes-pypi` class include :term:`SRC_URI`, :term:`SECTION`, :term:`HOMEPAGE`, :term:`UPSTREAM_CHECK_URI`, :term:`UPSTREAM_CHECK_REGEX` and :term:`CVE_PRODUCT`. .. _ref-classes-python_flit_core: ``python_flit_core`` ==================== The :ref:`ref-classes-python_flit_core` class enables building Python modules which declare the `PEP-517 `__ compliant ``flit_core.buildapi`` ``build-backend`` in the ``[build-system]`` section of ``pyproject.toml`` (See `PEP-518 `__). Python modules built with ``flit_core.buildapi`` are pure Python (no ``C`` or ``Rust`` extensions). Internally this uses the :ref:`ref-classes-python_pep517` class. .. _ref-classes-python_pep517: ``python_pep517`` ================= The :ref:`ref-classes-python_pep517` class builds and installs a Python ``wheel`` binary archive (see `PEP-517 `__). Recipes wouldn't inherit this directly, instead typically another class will inherit this and add the relevant native dependencies. Examples of classes which do this are :ref:`ref-classes-python_flit_core`, :ref:`ref-classes-python_setuptools_build_meta`, and :ref:`ref-classes-python_poetry_core`. .. _ref-classes-python_poetry_core: ``python_poetry_core`` ====================== The :ref:`ref-classes-python_poetry_core` class enables building Python modules which use the `Poetry Core `__ build system. Internally this uses the :ref:`ref-classes-python_pep517` class. .. _ref-classes-python_pyo3: ``python_pyo3`` =============== The :ref:`ref-classes-python_pyo3` class helps make sure that Python extensions written in Rust and built with `PyO3 `__, properly set up the environment for cross compilation. This class is internal to the :ref:`ref-classes-python-setuptools3_rust` class and is not meant to be used directly in recipes. .. _ref-classes-python-setuptools3_rust: ``python-setuptools3_rust`` =========================== The :ref:`ref-classes-python-setuptools3_rust` class enables building Python extensions implemented in Rust with `PyO3 `__, which allows to compile and distribute Python extensions written in Rust as easily as if they were written in C. This class inherits the :ref:`ref-classes-setuptools3` and :ref:`ref-classes-python_pyo3` classes. .. _ref-classes-pixbufcache: ``pixbufcache`` =============== The :ref:`ref-classes-pixbufcache` class generates the proper post-install and post-remove (postinst/postrm) scriptlets for packages that install pixbuf loaders, which are used with ``gdk-pixbuf``. These scriptlets call ``update_pixbuf_cache`` to add the pixbuf loaders to the cache. Since the cache files are architecture-specific, ``update_pixbuf_cache`` is run using QEMU if the postinst scriptlets need to be run on the build host during image creation. If the pixbuf loaders being installed are in packages other than the recipe's main package, set :term:`PIXBUF_PACKAGES` to specify the packages containing the loaders. .. _ref-classes-pkgconfig: ``pkgconfig`` ============= The :ref:`ref-classes-pkgconfig` class provides a standard way to get header and library information by using ``pkg-config``. This class aims to smooth integration of ``pkg-config`` into libraries that use it. During staging, BitBake installs ``pkg-config`` data into the ``sysroots/`` directory. By making use of sysroot functionality within ``pkg-config``, the :ref:`ref-classes-pkgconfig` class no longer has to manipulate the files. .. _ref-classes-populate-sdk: ``populate_sdk`` ================ The :ref:`ref-classes-populate-sdk` class provides support for SDK-only recipes. For information on advantages gained when building a cross-development toolchain using the :ref:`ref-tasks-populate_sdk` task, see the ":ref:`sdk-manual/appendix-obtain:building an sdk installer`" section in the Yocto Project Application Development and the Extensible Software Development Kit (eSDK) manual. .. _ref-classes-populate-sdk-*: ``populate_sdk_*`` ================== The :ref:`ref-classes-populate-sdk-*` classes support SDK creation and consist of the following classes: - :ref:`populate_sdk_base `: The base class supporting SDK creation under all package managers (i.e. DEB, RPM, and opkg). - :ref:`populate_sdk_deb `: Supports creation of the SDK given the Debian package manager. - :ref:`populate_sdk_rpm `: Supports creation of the SDK given the RPM package manager. - :ref:`populate_sdk_ipk `: Supports creation of the SDK given the opkg (IPK format) package manager. - :ref:`populate_sdk_ext `: Supports extensible SDK creation under all package managers. The :ref:`populate_sdk_base ` class inherits the appropriate ``populate_sdk_*`` (i.e. ``deb``, ``rpm``, and ``ipk``) based on :term:`IMAGE_PKGTYPE`. The base class ensures all source and destination directories are established and then populates the SDK. After populating the SDK, the :ref:`populate_sdk_base ` class constructs two sysroots: ``${``\ :term:`SDK_ARCH`\ ``}-nativesdk``, which contains the cross-compiler and associated tooling, and the target, which contains a target root filesystem that is configured for the SDK usage. These two images reside in :term:`SDK_OUTPUT`, which consists of the following:: ${SDK_OUTPUT}/${SDK_ARCH}-nativesdk-pkgs ${SDK_OUTPUT}/${SDKTARGETSYSROOT}/target-pkgs Finally, the base populate SDK class creates the toolchain environment setup script, the tarball of the SDK, and the installer. The respective :ref:`populate_sdk_deb `, :ref:`populate_sdk_rpm `, and :ref:`populate_sdk_ipk ` classes each support the specific type of SDK. These classes are inherited by and used with the :ref:`populate_sdk_base ` class. For more information on the cross-development toolchain generation, see the ":ref:`overview-manual/concepts:cross-development toolchain generation`" section in the Yocto Project Overview and Concepts Manual. For information on advantages gained when building a cross-development toolchain using the :ref:`ref-tasks-populate_sdk` task, see the ":ref:`sdk-manual/appendix-obtain:building an sdk installer`" section in the Yocto Project Application Development and the Extensible Software Development Kit (eSDK) manual. .. _ref-classes-prexport: ``prexport`` ============ The :ref:`ref-classes-prexport` class provides functionality for exporting :term:`PR` values. .. note:: This class is not intended to be used directly. Rather, it is enabled when using "``bitbake-prserv-tool export``". .. _ref-classes-primport: ``primport`` ============ The :ref:`ref-classes-primport` class provides functionality for importing :term:`PR` values. .. note:: This class is not intended to be used directly. Rather, it is enabled when using "``bitbake-prserv-tool import``". .. _ref-classes-prserv: ``prserv`` ========== The :ref:`ref-classes-prserv` class provides functionality for using a :ref:`PR service ` in order to automatically manage the incrementing of the :term:`PR` variable for each recipe. This class is enabled by default because it is inherited by the :ref:`ref-classes-package` class. However, the OpenEmbedded build system will not enable the functionality of this class unless :term:`PRSERV_HOST` has been set. .. _ref-classes-ptest: ``ptest`` ========= The :ref:`ref-classes-ptest` class provides functionality for packaging and installing runtime tests for recipes that build software that provides these tests. This class is intended to be inherited by individual recipes. However, the class' functionality is largely disabled unless "ptest" appears in :term:`DISTRO_FEATURES`. See the ":ref:`dev-manual/packages:testing packages with ptest`" section in the Yocto Project Development Tasks Manual for more information on ptest. .. _ref-classes-ptest-cargo: ``ptest-cargo`` =============== The :ref:`ref-classes-ptest-cargo` class is a class which extends the :ref:`ref-classes-cargo` class and adds ``compile_ptest_cargo`` and ``install_ptest_cargo`` steps to respectively build and install test suites defined in the ``Cargo.toml`` file, into a dedicated ``-ptest`` package. .. _ref-classes-ptest-gnome: ``ptest-gnome`` =============== Enables package tests (ptests) specifically for GNOME packages, which have tests intended to be executed with ``gnome-desktop-testing``. For information on setting up and running ptests, see the ":ref:`dev-manual/packages:testing packages with ptest`" section in the Yocto Project Development Tasks Manual. .. _ref-classes-python3-dir: ``python3-dir`` =============== The :ref:`ref-classes-python3-dir` class provides the base version, location, and site package location for Python 3. .. _ref-classes-python3native: ``python3native`` ================= The :ref:`ref-classes-python3native` class supports using the native version of Python 3 built by the build system rather than support of the version provided by the build host. .. _ref-classes-python3targetconfig: ``python3targetconfig`` ======================= The :ref:`ref-classes-python3targetconfig` class supports using the native version of Python 3 built by the build system rather than support of the version provided by the build host, except that the configuration for the target machine is accessible (such as correct installation directories). This also adds a dependency on target ``python3``, so should only be used where appropriate in order to avoid unnecessarily lengthening builds. .. _ref-classes-qemu: ``qemu`` ======== The :ref:`ref-classes-qemu` class provides functionality for recipes that either need QEMU or test for the existence of QEMU. Typically, this class is used to run programs for a target system on the build host using QEMU's application emulation mode. .. _ref-classes-recipe_sanity: ``recipe_sanity`` ================= The :ref:`ref-classes-recipe_sanity` class checks for the presence of any host system recipe prerequisites that might affect the build (e.g. variables that are set or software that is present). .. _ref-classes-relocatable: ``relocatable`` =============== The :ref:`ref-classes-relocatable` class enables relocation of binaries when they are installed into the sysroot. This class makes use of the :ref:`ref-classes-chrpath` class and is used by both the :ref:`ref-classes-cross` and :ref:`ref-classes-native` classes. .. _ref-classes-remove-libtool: ``remove-libtool`` ================== The :ref:`ref-classes-remove-libtool` class adds a post function to the :ref:`ref-tasks-install` task to remove all ``.la`` files installed by ``libtool``. Removing these files results in them being absent from both the sysroot and target packages. If a recipe needs the ``.la`` files to be installed, then the recipe can override the removal by setting ``REMOVE_LIBTOOL_LA`` to "0" as follows:: REMOVE_LIBTOOL_LA = "0" .. note:: The :ref:`ref-classes-remove-libtool` class is not enabled by default. .. _ref-classes-report-error: ``report-error`` ================ The :ref:`ref-classes-report-error` class supports enabling the :ref:`error reporting tool `", which allows you to submit build error information to a central database. The class collects debug information for recipe, recipe version, task, machine, distro, build system, target system, host distro, branch, commit, and log. From the information, report files using a JSON format are created and stored in ``${``\ :term:`LOG_DIR`\ ``}/error-report``. .. _ref-classes-rm-work: ``rm_work`` =========== The :ref:`ref-classes-rm-work` class supports deletion of temporary workspace, which can ease your hard drive demands during builds. The OpenEmbedded build system can use a substantial amount of disk space during the build process. A portion of this space is the work files under the ``${TMPDIR}/work`` directory for each recipe. Once the build system generates the packages for a recipe, the work files for that recipe are no longer needed. However, by default, the build system preserves these files for inspection and possible debugging purposes. If you would rather have these files deleted to save disk space as the build progresses, you can enable :ref:`ref-classes-rm-work` by adding the following to your ``local.conf`` file, which is found in the :term:`Build Directory`:: INHERIT += "rm_work" If you are modifying and building source code out of the work directory for a recipe, enabling :ref:`ref-classes-rm-work` will potentially result in your changes to the source being lost. To exclude some recipes from having their work directories deleted by :ref:`ref-classes-rm-work`, you can add the names of the recipe or recipes you are working on to the :term:`RM_WORK_EXCLUDE` variable, which can also be set in your ``local.conf`` file. Here is an example:: RM_WORK_EXCLUDE += "busybox glibc" .. _ref-classes-rootfs*: ``rootfs*`` =========== The :ref:`ref-classes-rootfs*` classes support creating the root filesystem for an image and consist of the following classes: - The :ref:`rootfs-postcommands ` class, which defines filesystem post-processing functions for image recipes. - The :ref:`rootfs_deb ` class, which supports creation of root filesystems for images built using ``.deb`` packages. - The :ref:`rootfs_rpm ` class, which supports creation of root filesystems for images built using ``.rpm`` packages. - The :ref:`rootfs_ipk ` class, which supports creation of root filesystems for images built using ``.ipk`` packages. - The :ref:`rootfsdebugfiles ` class, which installs additional files found on the build host directly into the root filesystem. The root filesystem is created from packages using one of the :ref:`ref-classes-rootfs*` files as determined by the :term:`PACKAGE_CLASSES` variable. For information on how root filesystem images are created, see the ":ref:`overview-manual/concepts:image generation`" section in the Yocto Project Overview and Concepts Manual. .. _ref-classes-rust: ``rust`` ======== The :ref:`ref-classes-rust` class is an internal class which is just used in the "rust" recipe, to build the Rust compiler and runtime library. Except for this recipe, it is not intended to be used directly. .. _ref-classes-rust-common: ``rust-common`` =============== The :ref:`ref-classes-rust-common` class is an internal class to the :ref:`ref-classes-cargo_common` and :ref:`ref-classes-rust` classes and is not intended to be used directly. .. _ref-classes-sanity: ``sanity`` ========== The :ref:`ref-classes-sanity` class checks to see if prerequisite software is present on the host system so that users can be notified of potential problems that might affect their build. The class also performs basic user configuration checks from the ``local.conf`` configuration file to prevent common mistakes that cause build failures. Distribution policy usually determines whether to include this class. .. _ref-classes-scons: ``scons`` ========= The :ref:`ref-classes-scons` class supports recipes that need to build software that uses the SCons build system. You can use the :term:`EXTRA_OESCONS` variable to specify additional configuration options you want to pass SCons command line. .. _ref-classes-sdl: ``sdl`` ======= The :ref:`ref-classes-sdl` class supports recipes that need to build software that uses the Simple DirectMedia Layer (SDL) library. .. _ref-classes-python_setuptools_build_meta: ``python_setuptools_build_meta`` ================================ The :ref:`ref-classes-python_setuptools_build_meta` class enables building Python modules which declare the `PEP-517 `__ compliant ``setuptools.build_meta`` ``build-backend`` in the ``[build-system]`` section of ``pyproject.toml`` (See `PEP-518 `__). Python modules built with ``setuptools.build_meta`` can be pure Python or include ``C`` or ``Rust`` extensions). Internally this uses the :ref:`ref-classes-python_pep517` class. .. _ref-classes-setuptools3: ``setuptools3`` =============== The :ref:`ref-classes-setuptools3` class supports Python version 3.x extensions that use build systems based on ``setuptools`` (e.g. only have a ``setup.py`` and have not migrated to the official ``pyproject.toml`` format). If your recipe uses these build systems, the recipe needs to inherit the :ref:`ref-classes-setuptools3` class. .. note:: The :ref:`ref-classes-setuptools3` class :ref:`ref-tasks-compile` task now calls ``setup.py bdist_wheel`` to build the ``wheel`` binary archive format (See `PEP-427 `__). A consequence of this is that legacy software still using deprecated ``distutils`` from the Python standard library cannot be packaged as ``wheels``. A common solution is the replace ``from distutils.core import setup`` with ``from setuptools import setup``. .. note:: The :ref:`ref-classes-setuptools3` class :ref:`ref-tasks-install` task now installs the ``wheel`` binary archive. In current versions of ``setuptools`` the legacy ``setup.py install`` method is deprecated. If the ``setup.py`` cannot be used with wheels, for example it creates files outside of the Python module or standard entry points, then :ref:`ref-classes-setuptools3_legacy` should be used. .. _ref-classes-setuptools3_legacy: ``setuptools3_legacy`` ====================== The :ref:`ref-classes-setuptools3_legacy` class supports Python version 3.x extensions that use build systems based on ``setuptools`` (e.g. only have a ``setup.py`` and have not migrated to the official ``pyproject.toml`` format). Unlike :ref:`ref-classes-setuptools3`, this uses the traditional ``setup.py`` ``build`` and ``install`` commands and not wheels. This use of ``setuptools`` like this is `deprecated `__ but still relatively common. .. _ref-classes-setuptools3-base: ``setuptools3-base`` ==================== The :ref:`ref-classes-setuptools3-base` class provides a reusable base for other classes that support building Python version 3.x extensions. If you need functionality that is not provided by the :ref:`ref-classes-setuptools3` class, you may want to ``inherit setuptools3-base``. Some recipes do not need the tasks in the :ref:`ref-classes-setuptools3` class and inherit this class instead. .. _ref-classes-sign_rpm: ``sign_rpm`` ============ The :ref:`ref-classes-sign_rpm` class supports generating signed RPM packages. .. _ref-classes-siteconfig: ``siteconfig`` ============== The :ref:`ref-classes-siteconfig` class provides functionality for handling site configuration. The class is used by the :ref:`ref-classes-autotools` class to accelerate the :ref:`ref-tasks-configure` task. .. _ref-classes-siteinfo: ``siteinfo`` ============ The :ref:`ref-classes-siteinfo` class provides information about the targets that might be needed by other classes or recipes. As an example, consider Autotools, which can require tests that must execute on the target hardware. Since this is not possible in general when cross compiling, site information is used to provide cached test results so these tests can be skipped over but still make the correct values available. The ``meta/site directory`` contains test results sorted into different categories such as architecture, endianness, and the ``libc`` used. Site information provides a list of files containing data relevant to the current build in the :term:`CONFIG_SITE` variable that Autotools automatically picks up. The class also provides variables like :term:`SITEINFO_ENDIANNESS` and :term:`SITEINFO_BITS` that can be used elsewhere in the metadata. .. _ref-classes-sstate: ``sstate`` ========== The :ref:`ref-classes-sstate` class provides support for Shared State (sstate). By default, the class is enabled through the :term:`INHERIT_DISTRO` variable's default value. For more information on sstate, see the ":ref:`overview-manual/concepts:shared state cache`" section in the Yocto Project Overview and Concepts Manual. .. _ref-classes-staging: ``staging`` =========== The :ref:`ref-classes-staging` class installs files into individual recipe work directories for sysroots. The class contains the following key tasks: - The :ref:`ref-tasks-populate_sysroot` task, which is responsible for handing the files that end up in the recipe sysroots. - The :ref:`ref-tasks-prepare_recipe_sysroot` task (a "partner" task to the ``populate_sysroot`` task), which installs the files into the individual recipe work directories (i.e. :term:`WORKDIR`). The code in the :ref:`ref-classes-staging` class is complex and basically works in two stages: - *Stage One:* The first stage addresses recipes that have files they want to share with other recipes that have dependencies on the originating recipe. Normally these dependencies are installed through the :ref:`ref-tasks-install` task into ``${``\ :term:`D`\ ``}``. The :ref:`ref-tasks-populate_sysroot` task copies a subset of these files into ``${SYSROOT_DESTDIR}``. This subset of files is controlled by the :term:`SYSROOT_DIRS`, :term:`SYSROOT_DIRS_NATIVE`, and :term:`SYSROOT_DIRS_IGNORE` variables. .. note:: Additionally, a recipe can customize the files further by declaring a processing function in the :term:`SYSROOT_PREPROCESS_FUNCS` variable. A shared state (sstate) object is built from these files and the files are placed into a subdirectory of :ref:`structure-build-tmp-sysroots-components`. The files are scanned for hardcoded paths to the original installation location. If the location is found in text files, the hardcoded locations are replaced by tokens and a list of the files needing such replacements is created. These adjustments are referred to as "FIXMEs". The list of files that are scanned for paths is controlled by the :term:`SSTATE_SCAN_FILES` variable. - *Stage Two:* The second stage addresses recipes that want to use something from another recipe and declare a dependency on that recipe through the :term:`DEPENDS` variable. The recipe will have a :ref:`ref-tasks-prepare_recipe_sysroot` task and when this task executes, it creates the ``recipe-sysroot`` and ``recipe-sysroot-native`` in the recipe work directory (i.e. :term:`WORKDIR`). The OpenEmbedded build system creates hard links to copies of the relevant files from ``sysroots-components`` into the recipe work directory. .. note:: If hard links are not possible, the build system uses actual copies. The build system then addresses any "FIXMEs" to paths as defined from the list created in the first stage. Finally, any files in ``${bindir}`` within the sysroot that have the prefix "``postinst-``" are executed. .. note:: Although such sysroot post installation scripts are not recommended for general use, the files do allow some issues such as user creation and module indexes to be addressed. Because recipes can have other dependencies outside of :term:`DEPENDS` (e.g. ``do_unpack[depends] += "tar-native:do_populate_sysroot"``), the sysroot creation function ``extend_recipe_sysroot`` is also added as a pre-function for those tasks whose dependencies are not through :term:`DEPENDS` but operate similarly. When installing dependencies into the sysroot, the code traverses the dependency graph and processes dependencies in exactly the same way as the dependencies would or would not be when installed from sstate. This processing means, for example, a native tool would have its native dependencies added but a target library would not have its dependencies traversed or installed. The same sstate dependency code is used so that builds should be identical regardless of whether sstate was used or not. For a closer look, see the ``setscene_depvalid()`` function in the :ref:`ref-classes-sstate` class. The build system is careful to maintain manifests of the files it installs so that any given dependency can be installed as needed. The sstate hash of the installed item is also stored so that if it changes, the build system can reinstall it. .. _ref-classes-syslinux: ``syslinux`` ============ The :ref:`ref-classes-syslinux` class provides syslinux-specific functions for building bootable images. The class supports the following variables: - :term:`INITRD`: Indicates list of filesystem images to concatenate and use as an initial RAM disk (initrd). This variable is optional. - :term:`ROOTFS`: Indicates a filesystem image to include as the root filesystem. This variable is optional. - :term:`AUTO_SYSLINUXMENU`: Enables creating an automatic menu when set to "1". - :term:`LABELS`: Lists targets for automatic configuration. - :term:`APPEND`: Lists append string overrides for each label. - :term:`SYSLINUX_OPTS`: Lists additional options to add to the syslinux file. Semicolon characters separate multiple options. - :term:`SYSLINUX_SPLASH`: Lists a background for the VGA boot menu when you are using the boot menu. - :term:`SYSLINUX_DEFAULT_CONSOLE`: Set to "console=ttyX" to change kernel boot default console. - :term:`SYSLINUX_SERIAL`: Sets an alternate serial port. Or, turns off serial when the variable is set with an empty string. - :term:`SYSLINUX_SERIAL_TTY`: Sets an alternate "console=tty..." kernel boot argument. .. _ref-classes-systemd: ``systemd`` =========== The :ref:`ref-classes-systemd` class provides support for recipes that install systemd unit files. The functionality for this class is disabled unless you have "systemd" in :term:`DISTRO_FEATURES`. Under this class, the recipe or Makefile (i.e. whatever the recipe is calling during the :ref:`ref-tasks-install` task) installs unit files into ``${``\ :term:`D`\ ``}${systemd_unitdir}/system``. If the unit files being installed go into packages other than the main package, you need to set :term:`SYSTEMD_PACKAGES` in your recipe to identify the packages in which the files will be installed. You should set :term:`SYSTEMD_SERVICE` to the name of the service file. You should also use a package name override to indicate the package to which the value applies. If the value applies to the recipe's main package, use ``${``\ :term:`PN`\ ``}``. Here is an example from the connman recipe:: SYSTEMD_SERVICE:${PN} = "connman.service" Services are set up to start on boot automatically unless you have set :term:`SYSTEMD_AUTO_ENABLE` to "disable". For more information on :ref:`ref-classes-systemd`, see the ":ref:`dev-manual/init-manager:selecting an initialization manager`" section in the Yocto Project Development Tasks Manual. .. _ref-classes-systemd-boot: ``systemd-boot`` ================ The :ref:`ref-classes-systemd-boot` class provides functions specific to the systemd-boot bootloader for building bootable images. This is an internal class and is not intended to be used directly. .. note:: The :ref:`ref-classes-systemd-boot` class is a result from merging the ``gummiboot`` class used in previous Yocto Project releases with the ``systemd`` project. Set the :term:`EFI_PROVIDER` variable to ":ref:`ref-classes-systemd-boot`" to use this class. Doing so creates a standalone EFI bootloader that is not dependent on systemd. For information on more variables used and supported in this class, see the :term:`SYSTEMD_BOOT_CFG`, :term:`SYSTEMD_BOOT_ENTRIES`, and :term:`SYSTEMD_BOOT_TIMEOUT` variables. You can also see the `Systemd-boot documentation `__ for more information. .. _ref-classes-terminal: ``terminal`` ============ The :ref:`ref-classes-terminal` class provides support for starting a terminal session. The :term:`OE_TERMINAL` variable controls which terminal emulator is used for the session. Other classes use the :ref:`ref-classes-terminal` class anywhere a separate terminal session needs to be started. For example, the :ref:`ref-classes-patch` class assuming :term:`PATCHRESOLVE` is set to "user", the :ref:`ref-classes-cml1` class, and the :ref:`ref-classes-devshell` class all use the :ref:`ref-classes-terminal` class. .. _ref-classes-testimage: ``testimage`` ============= The :ref:`ref-classes-testimage` class supports running automated tests against images using QEMU and on actual hardware. The classes handle loading the tests and starting the image. To use the classes, you need to perform steps to set up the environment. To enable this class, add the following to your configuration:: IMAGE_CLASSES += "testimage" The tests are commands that run on the target system over ``ssh``. Each test is written in Python and makes use of the ``unittest`` module. The :ref:`ref-classes-testimage` class runs tests on an image when called using the following:: $ bitbake -c testimage image Alternatively, if you wish to have tests automatically run for each image after it is built, you can set :term:`TESTIMAGE_AUTO`:: TESTIMAGE_AUTO = "1" For information on how to enable, run, and create new tests, see the ":ref:`dev-manual/runtime-testing:performing automated runtime testing`" section in the Yocto Project Development Tasks Manual. .. _ref-classes-testsdk: ``testsdk`` =========== This class supports running automated tests against software development kits (SDKs). The :ref:`ref-classes-testsdk` class runs tests on an SDK when called using the following:: $ bitbake -c testsdk image .. note:: Best practices include using :term:`IMAGE_CLASSES` rather than :term:`INHERIT` to inherit the :ref:`ref-classes-testsdk` class for automated SDK testing. .. _ref-classes-texinfo: ``texinfo`` =========== This class should be inherited by recipes whose upstream packages invoke the ``texinfo`` utilities at build-time. Native and cross recipes are made to use the dummy scripts provided by ``texinfo-dummy-native``, for improved performance. Target architecture recipes use the genuine Texinfo utilities. By default, they use the Texinfo utilities on the host system. .. note:: If you want to use the Texinfo recipe shipped with the build system, you can remove "texinfo-native" from :term:`ASSUME_PROVIDED` and makeinfo from :term:`SANITY_REQUIRED_UTILITIES`. .. _ref-classes-toaster: ``toaster`` =========== The :ref:`ref-classes-toaster` class collects information about packages and images and sends them as events that the BitBake user interface can receive. The class is enabled when the Toaster user interface is running. This class is not intended to be used directly. .. _ref-classes-toolchain-scripts: ``toolchain-scripts`` ===================== The :ref:`ref-classes-toolchain-scripts` class provides the scripts used for setting up the environment for installed SDKs. .. _ref-classes-typecheck: ``typecheck`` ============= The :ref:`ref-classes-typecheck` class provides support for validating the values of variables set at the configuration level against their defined types. The OpenEmbedded build system allows you to define the type of a variable using the "type" varflag. Here is an example:: IMAGE_FEATURES[type] = "list" .. _ref-classes-uboot-config: ``uboot-config`` ================ The :ref:`ref-classes-uboot-config` class provides support for U-Boot configuration for a machine. Specify the machine in your recipe as follows:: UBOOT_CONFIG ??= UBOOT_CONFIG[foo] = "config,images,binary" You can also specify the machine using this method:: UBOOT_MACHINE = "config" See the :term:`UBOOT_CONFIG` and :term:`UBOOT_MACHINE` variables for additional information. .. _ref-classes-uboot-sign: ``uboot-sign`` ============== The :ref:`ref-classes-uboot-sign` class provides support for U-Boot verified boot. It is intended to be inherited from U-Boot recipes. The variables used by this class are: - :term:`SPL_MKIMAGE_DTCOPTS`: DTC options for U-Boot ``mkimage`` when building the FIT image. - :term:`SPL_SIGN_ENABLE`: enable signing the FIT image. - :term:`SPL_SIGN_KEYDIR`: directory containing the signing keys. - :term:`SPL_SIGN_KEYNAME`: base filename of the signing keys. - :term:`UBOOT_FIT_ADDRESS_CELLS`: ``#address-cells`` value for the FIT image. - :term:`UBOOT_FIT_DESC`: description string encoded into the FIT image. - :term:`UBOOT_FIT_GENERATE_KEYS`: generate the keys if they don't exist yet. - :term:`UBOOT_FIT_HASH_ALG`: hash algorithm for the FIT image. - :term:`UBOOT_FIT_KEY_GENRSA_ARGS`: ``openssl genrsa`` arguments. - :term:`UBOOT_FIT_KEY_REQ_ARGS`: ``openssl req`` arguments. - :term:`UBOOT_FIT_SIGN_ALG`: signature algorithm for the FIT image. - :term:`UBOOT_FIT_SIGN_NUMBITS`: size of the private key for FIT image signing. - :term:`UBOOT_FIT_KEY_SIGN_PKCS`: algorithm for the public key certificate for FIT image signing. - :term:`UBOOT_FITIMAGE_ENABLE`: enable the generation of a U-Boot FIT image. - :term:`UBOOT_MKIMAGE_DTCOPTS`: DTC options for U-Boot ``mkimage`` when rebuilding the FIT image containing the kernel. See U-Boot's documentation for details about `verified boot `__ and the `signature process `__. See also the description of :ref:`ref-classes-kernel-fitimage` class, which this class imitates. .. _ref-classes-uninative: ``uninative`` ============= Attempts to isolate the build system from the host distribution's C library in order to make re-use of native shared state artifacts across different host distributions practical. With this class enabled, a tarball containing a pre-built C library is downloaded at the start of the build. In the Poky reference distribution this is enabled by default through ``meta/conf/distro/include/yocto-uninative.inc``. Other distributions that do not derive from poky can also "``require conf/distro/include/yocto-uninative.inc``" to use this. Alternatively if you prefer, you can build the uninative-tarball recipe yourself, publish the resulting tarball (e.g. via HTTP) and set ``UNINATIVE_URL`` and ``UNINATIVE_CHECKSUM`` appropriately. For an example, see the ``meta/conf/distro/include/yocto-uninative.inc``. The :ref:`ref-classes-uninative` class is also used unconditionally by the extensible SDK. When building the extensible SDK, ``uninative-tarball`` is built and the resulting tarball is included within the SDK. .. _ref-classes-update-alternatives: ``update-alternatives`` ======================= The :ref:`ref-classes-update-alternatives` class helps the alternatives system when multiple sources provide the same command. This situation occurs when several programs that have the same or similar function are installed with the same name. For example, the ``ar`` command is available from the ``busybox``, ``binutils`` and ``elfutils`` packages. The :ref:`ref-classes-update-alternatives` class handles renaming the binaries so that multiple packages can be installed without conflicts. The ``ar`` command still works regardless of which packages are installed or subsequently removed. The class renames the conflicting binary in each package and symlinks the highest priority binary during installation or removal of packages. To use this class, you need to define a number of variables: - :term:`ALTERNATIVE` - :term:`ALTERNATIVE_LINK_NAME` - :term:`ALTERNATIVE_TARGET` - :term:`ALTERNATIVE_PRIORITY` These variables list alternative commands needed by a package, provide pathnames for links, default links for targets, and so forth. For details on how to use this class, see the comments in the :yocto_git:`update-alternatives.bbclass ` file. .. note:: You can use the ``update-alternatives`` command directly in your recipes. However, this class simplifies things in most cases. .. _ref-classes-update-rc.d: ``update-rc.d`` =============== The :ref:`ref-classes-update-rc.d` class uses ``update-rc.d`` to safely install an initialization script on behalf of the package. The OpenEmbedded build system takes care of details such as making sure the script is stopped before a package is removed and started when the package is installed. Three variables control this class: :term:`INITSCRIPT_PACKAGES`, :term:`INITSCRIPT_NAME` and :term:`INITSCRIPT_PARAMS`. See the variable links for details. .. _ref-classes-useradd: ``useradd*`` ============ The :ref:`useradd* ` classes support the addition of users or groups for usage by the package on the target. For example, if you have packages that contain system services that should be run under their own user or group, you can use these classes to enable creation of the user or group. The :oe_git:`meta-skeleton/recipes-skeleton/useradd/useradd-example.bb ` recipe in the :term:`Source Directory` provides a simple example that shows how to add three users and groups to two packages. The :ref:`useradd_base ` class provides basic functionality for user or groups settings. The :ref:`useradd* ` classes support the :term:`USERADD_PACKAGES`, :term:`USERADD_PARAM`, :term:`GROUPADD_PARAM`, and :term:`GROUPMEMS_PARAM` variables. The :ref:`useradd-staticids ` class supports the addition of users or groups that have static user identification (``uid``) and group identification (``gid``) values. The default behavior of the OpenEmbedded build system for assigning ``uid`` and ``gid`` values when packages add users and groups during package install time is to add them dynamically. This works fine for programs that do not care what the values of the resulting users and groups become. In these cases, the order of the installation determines the final ``uid`` and ``gid`` values. However, if non-deterministic ``uid`` and ``gid`` values are a problem, you can override the default, dynamic application of these values by setting static values. When you set static values, the OpenEmbedded build system looks in :term:`BBPATH` for ``files/passwd`` and ``files/group`` files for the values. To use static ``uid`` and ``gid`` values, you need to set some variables. See the :term:`USERADDEXTENSION`, :term:`USERADD_UID_TABLES`, :term:`USERADD_GID_TABLES`, and :term:`USERADD_ERROR_DYNAMIC` variables. You can also see the :ref:`ref-classes-useradd` class for additional information. .. note:: You do not use the :ref:`useradd-staticids ` class directly. You either enable or disable the class by setting the :term:`USERADDEXTENSION` variable. If you enable or disable the class in a configured system, :term:`TMPDIR` might contain incorrect ``uid`` and ``gid`` values. Deleting the :term:`TMPDIR` directory will correct this condition. .. _ref-classes-utility-tasks: ``utility-tasks`` ================= The :ref:`ref-classes-utility-tasks` class provides support for various "utility" type tasks that are applicable to all recipes, such as :ref:`ref-tasks-clean` and :ref:`ref-tasks-listtasks`. This class is enabled by default because it is inherited by the :ref:`ref-classes-base` class. .. _ref-classes-utils: ``utils`` ========= The :ref:`ref-classes-utils` class provides some useful Python functions that are typically used in inline Python expressions (e.g. ``${@...}``). One example use is for ``bb.utils.contains()``. This class is enabled by default because it is inherited by the :ref:`ref-classes-base` class. .. _ref-classes-vala: ``vala`` ======== The :ref:`ref-classes-vala` class supports recipes that need to build software written using the Vala programming language. .. _ref-classes-waf: ``waf`` ======= The :ref:`ref-classes-waf` class supports recipes that need to build software that uses the Waf build system. You can use the :term:`EXTRA_OECONF` or :term:`PACKAGECONFIG_CONFARGS` variables to specify additional configuration options to be passed on the Waf command line.