[linux-yocto] v2 RR for xilinx-zynqmp bsp for build and boot
Zumeng Chen
zchen at windriver.com
Wed Jun 5 20:50:53 PDT 2019
On 6/6/19 9:18 AM, Zumeng Chen wrote:
> Hi Bruce,
>
> Here are the v2 changes for scc/cfg:
>
> *) Create the minimum cfg set for arm/arm64, and include it
> *) Remove those CFG only existed in Xilinx SDK.
> *) Include hotplug scc
> *) Remove some non-validation features, like remoteproc.
>
> As for bsp/xilinx, I think someone need to polish it, trust me :)
> No kernel build warnings. And the boot process is still OK.
>
> Cheers,
> Zumeng
>
> commit 30cc68182cdd6254b58795fb3afedaceb6949a70
> Author: Zumeng Chen <zumeng.chen at windriver.com>
> Date: Thu Jun 6 08:44:57 2019 +0800
>
> xilinx-zynqmp: add the basic support xilinx-zynqmp
>
> This patch is to add scc/cfg meta to build and boot zcu102 board with the bsp
> of xilinx-zynqmp.
>
> Signed-off-by: Zumeng.Chen <zumeng.chen at windriver.com>
>
> commit d910c163028e0cfa268886007fd2dbbf6a5d9f20
> Author: Zumeng Chen <zumeng.chen at windriver.com>
> Date: Thu Jun 6 08:45:16 2019 +0800
>
> power: create the minimum set of cpu idle and cpufreq scaling for arm/arm64
>
> This patch is to create the minimum set for cpu idle/freq scaling, which is ok
> to both arm and arm64 with DT enablement. And we leave more specific features
> to the end users.
>
> Signed-off-by: Zumeng.Chen <zumeng.chen at windriver.com>
>
>
> Added Files:
> ------------
> bsp/xilinx-zynqmp/xilinx-zynqmp-standard.scc | 8 ++
> bsp/xilinx-zynqmp/xilinx-zynqmp.cfg | 167 +++++++++++++++++++++++++++
> bsp/xilinx-zynqmp/xilinx-zynqmp.scc | 10 ++
> features/power/arm.cfg | 7 ++
> features/power/arm.scc | 4 +
>
> Removed Files:
> --------------
> None.
>
> Remaining Changes (diffstat):
> -----------------------------
> None.
This comes from core-image-sato-xilinx-zynqmp.tar.bz2
ZynqMP> setenv bootargs console=ttyPS0,115200 root=/dev/mmcblk0p3 rw
rootwait earlycon=cdns,mmio,0xFF000000 clk_ignore_unused ip=dhcp
ZynqMP> tftpboot 0x10000000 Image; tftpboot 0x11800000 dtb; booti
0x10000000 - 0x11800000
Using ethernet at ff0e0000 device
Filename 'Image'.
Load address: 0x10000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###########
11.3 MiB/s
done
Bytes transferred = 16378368 (f9ea00 hex)
Using ethernet at ff0e0000 device
TFTP from server 128.224.162.211; our IP address is 128.224.162.99
Filename 'dtb'.
Load address: 0x11800000
Loading: ##
4.7 MiB/s
done
Bytes transferred = 19746 (4d22 hex)
## Flattened Device Tree blob at 11800000
Booting using the fdt blob at 0x11800000
Loading Device Tree to 0000000007ff8000, end 0000000007fffd21 ... OK
Starting kernel ...
Booting Linux on physical CPU 0x0000000000 [0x410fd034]
Linux version 5.2.0-rc3-yoctodev-standard (oe-user at oe-host) (gcc version
9.1.0 (GCC)) #1 SMP PREEMPT Thu Jun 6 00:53:26 UTC 2019
Machine model: ZynqMP ZCU102 Rev1.0
earlycon: cdns0 at MMIO 0x00000000ff000000 (options '')
printk: bootconsole [cdns0] enabled
efi: Getting EFI parameters from FDT:
efi: UEFI not found.
cma: Reserved 16 MiB at 0x000000007ec00000
psci: probing for conduit method from DT.
psci: PSCIv1.1 detected in firmware.
psci: Using standard PSCI v0.2 function IDs
psci: MIGRATE_INFO_TYPE not supported.
psci: SMC Calling Convention v1.1
percpu: Embedded 30 pages/cpu s83416 r8192 d31272 u122880
Detected VIPT I-cache on CPU0
CPU features: detected: ARM erratum 845719
Speculative Store Bypass Disable mitigation not required
Built 1 zonelists, mobility grouping on. Total pages: 1031940
Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p3 rw
rootwait earlycon=cdns,mmio,0xFF000000 clk_ignore_unused ip=dhcp
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
software IO TLB: mapped [mem 0x7ac00000-0x7ec00000] (64MB)
Memory: 4013572K/4193280K available (10748K kernel code, 1210K rwdata,
2764K rodata, 1216K init, 757K bss, 163324K reserved, 16384K cma-reserved)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
ftrace: allocating 36121 entries in 142 pages
rcu: Preemptible hierarchical RCU implementation.
rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
Tasks RCU enabled.
rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
GIC: Adjusting CPU interface base to 0x00000000f902f000
GIC: Using split EOI/Deactivate mode
random: get_random_bytes called from start_kernel+0x328/0x4c4 with
crng_init=0
arch_timer: cp15 timer(s) running at 99.99MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles:
0x170f8de2d3, max_idle_ns: 440795206112 ns
sched_clock: 56 bits at 99MHz, resolution 10ns, wraps every 4398046511101ns
Console: colour dummy device 80x25
Calibrating delay loop (skipped), value calculated using timer
frequency.. 199.98 BogoMIPS (lpj=399960)
pid_max: default: 32768 minimum: 301
LSM: Security Framework initializing
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
*** VALIDATE proc ***
*** VALIDATE cgroup1 ***
*** VALIDATE cgroup2 ***
ASID allocator initialised with 32768 entries
rcu: Hierarchical SRCU implementation.
EFI services will not be available.
smp: Bringing up secondary CPUs ...
Detected VIPT I-cache on CPU1
CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
Detected VIPT I-cache on CPU2
CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
Detected VIPT I-cache on CPU3
CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
smp: Brought up 1 node, 4 CPUs
SMP: Total of 4 processors activated.
CPU features: detected: 32-bit EL0 Support
CPU features: detected: CRC32 instructions
CPU: All CPU(s) started at EL2
alternatives: patching kernel code
devtmpfs: initialized
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 7645041785100000 ns
futex hash table entries: 1024 (order: 4, 65536 bytes)
xor: measuring software checksum speed
8regs : 2360.000 MB/sec
32regs : 2706.000 MB/sec
arm64_neon: 2018.000 MB/sec
xor: using function: 32regs (2706.000 MB/sec)
DMI not present or invalid.
NET: Registered protocol family 16
cpuidle: using governor ladder
hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
DMA: preallocated 256 KiB pool for atomic allocations
��ɥ��ѭ console [ttyPS0] enabled 0xff000000 (irq = 33, base_baud =
6250000) is a xuartps
printk: console [ttyPS0] enabled
printk: bootconsole [cdns0] disabled
printk: bootconsole [cdns0] disabled
ff010000.serial: ttyPS1 at MMIO 0xff010000 (irq = 34, base_baud =
6250000) is a xuartps
HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
raid6: neonx8 gen() 1518 MB/s
raid6: neonx8 xor() 1442 MB/s
raid6: neonx4 gen() 1471 MB/s
raid6: neonx4 xor() 1409 MB/s
raid6: neonx2 gen() 1128 MB/s
raid6: neonx2 xor() 1175 MB/s
raid6: neonx1 gen() 737 MB/s
raid6: neonx1 xor() 887 MB/s
raid6: int64x8 gen() 1166 MB/s
raid6: int64x8 xor() 763 MB/s
raid6: int64x4 gen() 983 MB/s
raid6: int64x4 xor() 739 MB/s
raid6: int64x2 gen() 683 MB/s
raid6: int64x2 xor() 601 MB/s
raid6: int64x1 gen() 452 MB/s
raid6: int64x1 xor() 462 MB/s
raid6: using algorithm neonx8 gen() 1518 MB/s
raid6: .... xor() 1442 MB/s, rmw enabled
raid6: using neon recovery algorithm
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
videodev: Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
<giometti at linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
FPGA manager framework
clocksource: Switched to clocksource arch_sys_counter
*** VALIDATE hugetlbfs ***
NET: Registered protocol family 2
tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
UDP hash table entries: 2048 (order: 4, 65536 bytes)
UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
hw perfevents: no interrupt-affinity property for /pmu, guessing.
hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
kprobes: failed to populate blacklist: -22
Please take care of using kprobes.
workingset: timestamp_bits=46 max_order=20 bucket_order=0
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2. �© 2001-2006 Red Hat, Inc.
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
io scheduler mq-deadline registered
io scheduler kyber registered
nwl-pcie fd0e0000.pcie: Link is DOWN
nwl-pcie fd0e0000.pcie: host bridge /amba/pcie at fd0e0000 ranges:
nwl-pcie fd0e0000.pcie: MEM 0xe0000000..0xefffffff -> 0xe0000000
nwl-pcie fd0e0000.pcie: MEM 0x600000000..0x7ffffffff -> 0x600000000
nwl-pcie fd0e0000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
pci_bus 0000:00: root bus resource [mem 0x600000000-0x7ffffffff pref]
pci 0000:00:00.0: [10ee:d021] type 01 class 0x060400
pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:00.0: PCI bridge to [bus 01-0c]
pcieport 0000:00:00.0: PME: Signaling with IRQ 37
xilinx-zynqmp-dma fd500000.dma: ZynqMP DMA driver Probe success
xilinx-zynqmp-dma fd510000.dma: ZynqMP DMA driver Probe success
xilinx-zynqmp-dma fd520000.dma: ZynqMP DMA driver Probe success
xilinx-zynqmp-dma fd530000.dma: ZynqMP DMA driver Probe success
xilinx-zynqmp-dma fd540000.dma: ZynqMP DMA driver Probe success
xilinx-zynqmp-dma fd550000.dma: ZynqMP DMA driver Probe success
xilinx-zynqmp-dma fd560000.dma: ZynqMP DMA driver Probe success
xilinx-zynqmp-dma fd570000.dma: ZynqMP DMA driver Probe success
cacheinfo: Unable to detect cache hierarchy for CPU 0
brd: module loaded
loop: module loaded
ahci-ceva fd0c0000.ahci: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl
platform mode
ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio
slum part ccc sds apst
scsi host0: ahci-ceva
scsi host1: ahci-ceva
ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 31
ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 31
libphy: Fixed MDIO Bus: probed
CAN device driver interface
libphy: MACB_mii_bus: probed
Generic PHY ff0e0000.ethernet-ffffffff:0c: attached PHY driver [Generic
PHY] (mii_bus:phy_addr=ff0e0000.ethernet-ffffffff:0c, irq=POLL)
macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000
irq 20 (00:0a:35:04:9a:86)
dwc3 fe200000.usb: Failed to get clk 'ref': -2
dwc3 fe200000.usb: Configuration mismatch. dr_mode forced to host
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
xhci-hcd xhci-hcd.0.auto: hcc params 0x0238f625 hci version 0x100 quirks
0x0000000002010010
xhci-hcd xhci-hcd.0.auto: irq 35, io mem 0xfe200000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
rtc_zynqmp ffa60000.rtc: registered as rtc0
pca953x 0-0020: 0-0020 supply vcc not found, using dummy regulator
GPIO line 322 (sel0) hogged as output/low
GPIO line 323 (sel1) hogged as output/high
GPIO line 324 (sel2) hogged as output/high
GPIO line 325 (sel3) hogged as output/high
pca953x 0-0021: 0-0021 supply vcc not found, using dummy regulator
cdns-i2c ff020000.i2c: 400 kHz mmio ff020000 irq 22
cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 23
i2c i2c-0: Added multiplexed i2c bus 2
i2c i2c-0: Added multiplexed i2c bus 3
i2c i2c-0: Added multiplexed i2c bus 4
i2c i2c-0: Added multiplexed i2c bus 5
pca954x 0-0075: registered 4 multiplexed busses for I2C mux pca9544
at24 6-0054: 1024 byte 24c08 EEPROM, writable, 1 bytes/write
i2c i2c-1: Added multiplexed i2c bus 6
i2c i2c-7: of_i2c: modalias failure on
/amba/i2c at ff030000/i2c-mux at 74/i2c at 1/clock-generator at 36
i2c i2c-7: Failed to create I2C device for
/amba/i2c at ff030000/i2c-mux at 74/i2c at 1/clock-generator at 36
i2c i2c-1: Added multiplexed i2c bus 7
si570 8-005d: registered, current frequency 300000000 Hz
i2c i2c-1: Added multiplexed i2c bus 8
si570 9-005d: clock registration failed
si570: probe of 9-005d failed with error -17
i2c i2c-1: Added multiplexed i2c bus 9
i2c i2c-10: of_i2c: modalias failure on
/amba/i2c at ff030000/i2c-mux at 74/i2c at 4/clock-generator at 69
i2c i2c-10: Failed to create I2C device for
/amba/i2c at ff030000/i2c-mux at 74/i2c at 4/clock-generator at 69
i2c i2c-1: Added multiplexed i2c bus 10
i2c i2c-1: Added multiplexed i2c bus 11
i2c i2c-1: Added multiplexed i2c bus 12
i2c i2c-1: Added multiplexed i2c bus 13
pca954x 1-0074: registered 8 multiplexed busses for I2C switch pca9548
i2c i2c-1: Added multiplexed i2c bus 14
i2c i2c-1: Added multiplexed i2c bus 15
i2c i2c-1: Added multiplexed i2c bus 16
i2c i2c-1: Added multiplexed i2c bus 17
i2c i2c-1: Added multiplexed i2c bus 18
i2c i2c-1: Added multiplexed i2c bus 19
i2c i2c-1: Added multiplexed i2c bus 20
i2c i2c-1: Added multiplexed i2c bus 21
pca954x 1-0075: registered 8 multiplexed busses for I2C switch pca9548
ina2xx 2-0040: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 2-0041: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 2-0042: power monitor ina226 (Rshunt = 5000 uOhm)
ata1: SATA link down (SStatus 0 SControl 330)
ina2xx 2-0043: power monitor ina226 (Rshunt = 5000 uOhm)
ata2: SATA link down (SStatus 0 SControl 330)
ina2xx 2-0044: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 2-0045: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 2-0046: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 2-0047: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 2-004a: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 2-004b: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 3-0040: power monitor ina226 (Rshunt = 2000 uOhm)
ina2xx 3-0041: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 3-0042: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 3-0043: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 3-0044: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 3-0045: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 3-0046: power monitor ina226 (Rshunt = 5000 uOhm)
ina2xx 3-0047: power monitor ina226 (Rshunt = 5000 uOhm)
cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer at (____ptrval____)
with timeout 10s
device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised:
dm-devel at redhat.com
EDAC MC: ECC not enabled
cpu cpu0: failed to get clock: -2
cpufreq-dt: probe of cpufreq-dt failed with error -2
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
u32 classifier
Actions configured
NET: Registered protocol family 10
Segment Routing with IPv6
sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20170425 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20170425)
can: broadcast manager protocol (rev 20170425 t)
can: netlink gateway (rev 20170425) max_hops=1
Key type dns_resolver registered
registered taskstats version 1
Btrfs loaded, crc32c=crc32c-generic
Key type encrypted registered
printk: console [netcon0] enabled
netconsole: network logging started
rtc_zynqmp ffa60000.rtc: setting system clock to 2019-06-06T03:39:58 UTC
(1559792398)
macb ff0e0000.ethernet eth0: link up (1000/Full)
pps pps0: new PPS source ptp0
macb ff0e0000.ethernet: gem-ptp-timer ptp clock registered.
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
mmc0: Problem switching card into high-speed mode!
mmc0: new SDHC card at address 0001
mmcblk0: mmc0:0001 SD16G 14.5 GiB
Sending DHCP requests .
mmcblk0: p1 p2 p3
, OK
IP-Config: Complete:
device=eth0, hwaddr=00:0a:35:04:9a:86, ipaddr=xxxxx,
mask=255.255.254.0
host=xxx, domain=corp.ad.wrs.com, nis-domain=swamp
bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath=
clk: Not disabling unused clocks
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 179:3.
devtmpfs: mounted
Freeing unused kernel memory: 1216K
Run /sbin/init as init process
random: fast init done
systemd[1]: systemd 242-19-gdb2e367+ running in system mode. (+PAM
-AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP
-GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -)
systemd[1]: Detected architecture arm64.
Welcome to Wind River Linux development 19.23 Update 0!
systemd[1]: Set hostname to <xilinx-zynqmp>.
random: systemd: uninitialized urandom read (16 bytes read)
systemd[1]: Initializing machine ID from random generator.
systemd[1]: Failed to bump fs.file-max, ignoring: Invalid argument
systemd[1]: /lib/systemd/system/dbus.socket:4: ListenStream= references
a path below legacy directory /var/run/, updating
/var/run/dbus/system_bus_socket �→ /run/dbus/system_bus_socket; please
update the unit f.
systemd[1]: /lib/systemd/system/rpcbind.socket:4: ListenStream=
references a path below legacy directory /var/run/, updating
/var/run/rpcbind.sock �→ /run/rpcbind.sock; please update the unit file
accordingly.
random: systemd: uninitialized urandom read (16 bytes read)
systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
random: systemd: uninitialized urandom read (16 bytes read)
systemd[1]: Listening on Syslog Socket.
[ OK ] Listening on Syslog Socket.
systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ OK ] Listening on udev Control Socket.
[ OK ] Created slice User and Session Slice.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ OK ] Reached target Swap.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ OK ] Reached target Slices.
[ OK ] Listening on Journal Socket.
Starting udev Coldplug all Devices...
Mounting POSIX Message Queue File System...
Mounting Temporary Directory (/tmp)...
Starting Journal Service...
Starting Remount Root and Kernel File Systems...
Mounting Kernel Debug File System...
EXT4-fs (mmcblk0p3): re-mounted. Opts: (null)
Starting Create list of re�…odes for the current kernel...
[ OK ] Started Forward Password R�…uests to Wall Directory Watch.
[ OK ] Reached target Remote File Systems.
[ OK ] Listening on Network Service Netlink Socket.
Starting Apply Kernel Variables...
[ OK ] Started Dispatch Password �…ts to Console Directory Watch.
[ OK ] Reached target Paths.
[ OK ] Created slice system-getty.slice.
Mounting Huge Pages File System...
[ OK ] Started Journal Service.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Temporary Directory (/tmp).
[ OK ] Started Remount Root and Kernel File Systems.
[ OK ] Mounted Kernel Debug File System.
[ OK ] Started Create list of req�… nodes for the current kernel.
[ OK ] Started Apply Kernel Variables.
[ OK ] Mounted Huge Pages File System.
Starting Create System Users...
Starting Rebuild Hardware Database...
Starting Flush Journal to Persistent Storage...
[ OK ] Started udev Coldplug all Devices.
systemd-journald[148]: Received request to flush runtime journal from PID 1
[ OK ] Started Flush Journal to Persistent Storage.
[ OK ] Started Create System Users.
Starting Create Static Device Nodes in /dev...
[ OK ] Started Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
Mounting /var/volatile...
[ OK ] Mounted /var/volatile.
[ OK ] Reached target Local File Systems.
Starting Create Volatile Files and Directories...
Starting Load/Save Random Seed...
[ OK ] Started Load/Save Random Seed.
[ OK ] Started Create Volatile Files and Directories.
Starting Network Time Synchronization...
Starting Rebuild Journal Catalog...
Starting Update UTMP about System Boot/Shutdown...
Starting Run pending postinsts...
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Time Set.
[ OK ] Reached target System Time Synchronized.
[ OK ] Started Rebuild Journal Catalog.
[ OK ] Started Run pending postinsts.
[ OK ] Started Rebuild Hardware Database.
Starting udev Kernel Device Manager...
Starting Update is Completed...
[ OK ] Started Update is Completed.
[ OK ] Started udev Kernel Device Manager.
[ OK ] Reached target System Initialization.
Starting Console System Startup Logging...
[ OK ] Listening on RPCbind Server Activation Socket.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[ OK ] Listening on dropbear.socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
[ OK ] Started System Logging Service.
[ OK ] Started Dynamic Host Configuration Protocol (DHCP).
[ OK ] Started Kernel Logging Service.
Starting Login Service...
[ OK ] Started D-Bus System Message Bus.
[ OK ] Started Xserver startup without a display manager.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Timers.
Starting Telephony service...
Starting Network Service...
[ OK ] Started Console System Startup Logging.
[ OK ] Found device /dev/ttyPS0.
[ OK ] Listening on Load/Save RF �…itch Status /dev/rfkill Watch.
[ OK ] Started Network Service.
Starting Network Name Resolution...
[ OK ] Started Login Service.
[ OK ] Started Network Name Resolution.
[ OK ] Started Telephony service.
[ OK ] Reached target Network.
Starting Berkeley Internet Name Domain (DNS)...
Starting /etc/rc.local Compatibility...
Starting Permit User Sessions...
Starting Avahi mDNS/DNS-SD Stack...
[ OK ] Started /etc/rc.local Compatibility.
[ OK ] Started Permit User Sessions.
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on ttyPS0.
[ OK ] Started Avahi mDNS/DNS-SD Stack.
[ OK ] Started Berkeley Internet Name Domain (DNS).
[ OK ] Reached target Host and Network Name Lookups.
Wind River Linux development 19.23 Update 0 xilinx-zynqmp ttyPS0
xilinx-zynqmp login: root
root at xilinx-zynqmp:~# uname 0a
uname: extra operand '0a'
Try 'uname --help' for more information.
root at xilinx-zynqmp:~# uname -a
Linux xilinx-zynqmp 5.2.0-rc3-yoctodev-standard #1 SMP PREEMPT Thu Jun 6
00:53:26 UTC 2019 aarch64 aarch64 aarch64 GNU/Linux
>
> zchen at pek-lpggp4:$ bitbake -c menuconfig linux-yocto-dev
> WARNING: You have included the meta-openstack layer, but 'openstack' has not been enabled in your DISTRO_FEATURES. Some bbappend files and preferred version setting may not take effect. See the meta-openstack README for details on enabling openstack support.
> Loading cache: 100% |###############################################################################################################################################################################| Time: 0:00:01
> Loaded 8547 entries from dependency cache.
> Parsing recipes: 100% |#############################################################################################################################################################################| Time: 0:00:12
> Parsing of 3646 .bb files complete (3645 cached, 1 parsed). 8548 targets, 5846 skipped, 0 masked, 0 errors.
> WARNING: No recipes available for:
> /buildarea1/zchen/build-19/wr19-0606-arm64/layers/meta-cloud-services/meta-openstack/recipes-connectivity/openssh/openssh_7.%.bbappend
> /buildarea1/zchen/build-19/wr19-0606-arm64/layers/meta-cloud-services/meta-openstack/recipes-extended/iptables/iptables_1.6.%.bbappend
> /buildarea1/zchen/build-19/wr19-0606-arm64/layers/meta-cloud-services/meta-openstack/recipes-extended/libvirt/libvirt_4.%.bbappend
> /buildarea1/zchen/build-19/wr19-0606-arm64/layers/meta-cloud-services/meta-openstack/recipes-kernel/linux/linux-yocto_4.18.bbappend
> /buildarea1/zchen/build-19/wr19-0606-arm64/layers/meta-cloud-services/meta-openstack/recipes-support/iproute2/iproute2_4.%.bbappend
> /buildarea1/zchen/build-19/wr19-0606-arm64/layers/meta-cgl/meta-cgl-common/recipes-extended/umip/umip_%.bbappend
> WARNING: No bb files matched BBFILE_PATTERN_overc ''
> WARNING: No bb files matched BBFILE_PATTERN_cube ''
> WARNING: No bb files matched BBFILE_PATTERN_wrlinux-overc ''
> NOTE: Resolving any missing task queue dependencies
>
> Build Configuration:
> WRLINUX_VERSION = "10.19.23.0"
> WRLINUX_BRANCH = "development"
> BB_VERSION = "1.43.0"
> BUILD_SYS = "x86_64-linux"
> NATIVELSBSTRING = "universal"
> DISTRO = "wrlinux-std-sato"
> DISTRO_VERSION = "10.19.23.0"
> MACHINE = "xilinx-zynqmp"
> DEFAULTTUNE = "cortexa53"
> TARGET_SYS = "aarch64-wrs-linux"
> TUNE_FEATURES = "aarch64 cortexa53 crc"
> TARGET_FPU = ""
> lib32: DEFAULTTUNE = "armv7athf-neon"
> lib32: TARGET_SYS = "arm-wrsmllib32-linux-gnueabi"
> lib32: TUNE_FEATURES = "arm armv7a vfp thumb neon callconvention-hard"
> lib32: TARGET_FPU = "hard"
> wrlinux
> wrlinux-distro = "master-wr:da3279f6841a82f09311a4f64c15bd2817f6c41d"
> meta = "wr-10.19-20190603:c33e580dcaa12e40c6ec543c2c08f0ab5ff7d16d"
> meta-initramfs
> meta-xfce
> meta-oe
> meta-filesystems
> meta-webserver
> meta-networking
> meta-python
> meta-perl
> meta-gnome
> meta-multimedia = "wr-10.19-20190528:045e30366fc481f3b538a9f93df53b78b4abd9ef"
> meta-security = "wr-10.19-20190529:b73416279b6b7f1735146911bb953e9bb13eb08f"
> meta-selinux = "wr-10.19-20190424:38255864a6f8ba49f62c4d8c37106e5460d32cc3"
> intel-x86 = "master-wr:ad411c10245aeb78e8509e9e7b9e888e2fc8eb6c"
> xilinx-zynqmp = "master:3fb2dc44a72e070c40a71e041fc4dbc19b373ba6"
> meta-virtualization = "wr-10.19-20190603:90877b284996fcb47c0c5688a4f7b64c5539fff6"
> meta-realtime = "wr-10.19-20190408:9074810c117fdde9cec4058ac9c17c84f0f50420"
> meta-mingw = "wr-10.19-20190508:714437ac9ba52a4e022b3b199819dbb609d9952e"
> wr-template = "master-wr:4f4e06413262e09e9eadbad427860218485bb3c3"
> meta-yocto-bsp
> meta-poky = "wr-10.19-20190603:07770ce02d24f3bc8be8df93a5ee3e6c8b5827c7"
> meta-gplv2 = "wr-10.19-20190524:edc6680691596c9f889c3c0a0909d57d8d05b145"
> meta-efi-secure-boot
> meta-encrypted-storage
> meta-integrity
> meta-signing-key = "wr-10.19-20190524:b0a726761cc6dc203545240376c43e4673b87db8"
> meta-cloud-services = "wr-10.19-20190603:b0e2d2aec18998f51e810bb445614e89afcc932c"
> meta
> meta-ids
> meta-tpm
> meta-tpm2 = "wr-10.19-20190524:b0a726761cc6dc203545240376c43e4673b87db8"
> meta-openstack
> meta-openstack-aio-deploy
> meta-openstack-compute-deploy
> meta-openstack-compute-test-config
> meta-openstack-controller-deploy
> meta-openstack-controller-test-config
> meta-openstack-qemu
> meta-openstack-swift-deploy = "wr-10.19-20190603:b0e2d2aec18998f51e810bb445614e89afcc932c"
> meta-intel = "wr-10.19-20190603:359913d879a093ed168f426b9661416866f1ffd1"
> wrlinux-ovp = "master-wr:da3279f6841a82f09311a4f64c15bd2817f6c41d"
> meta-cgl-common = "wr-10.19-20190508:bfd0554ad9734a210b636f9f5bdc307df19b1e79"
> wrlinux-cgl = "master-wr:da3279f6841a82f09311a4f64c15bd2817f6c41d"
> meta-dpdk = "wr-10.19-20190528:0d5e26781a7bb332ef5677d2938f5ed4b7316a59"
> meta-intel-qat = "wr-10.19-20190408:7a49ca357fc1a130d5de2d6862168901f7229b14"
> meta-qemuarma9 = "wr-10.19-20190520:a4975ed30e5b213266f75a4bda8ab5b39f335781"
> meta-anaconda = "wr-10.19-20190603:2d99a13e927c4d4d824cc685fb99d28f0d860941"
> meta-overc
> meta-cube = "wr-10.19-20190520:4f7c0427acdf9ccab4e734840f1149840311a813"
> meta-iot-cloud = "wr-10.19-20190415:6e522eb46e35173eee5f9dd920bd32638aa00a11"
> wrlinux-overc = "master-wr:da3279f6841a82f09311a4f64c15bd2817f6c41d"
> wrlinux-overc-cfg = "master-wr:639a999f5b83640b075c0306ea53b3da8913522d"
> meta-selinux-dl = "master-wr:0e044fd49b16872966bf1d3c8e99d12df4bc6831"
> meta-mingw-dl = "master-wr:8fc9becbb6f0d96b86b55969238e69fb9d8d3bb5"
> meta-security-dl = "master-wr:d43ef6844eee8734f943f23e3e1a983b3094ca9e"
> meta-efi-secure-boot-dl = "master-wr:b79180d67c83c0fdf317c0583fa9a8e5fdb21b86"
> meta-encrypted-storage-dl = "master-wr:66323e9c6e55ecd52585172aab978d484c38038c"
> meta-integrity-dl = "master-wr:c1f5e6d034937f78b4082c3109942d2544e902b7"
> meta-ids-dl = "master-wr:3949731e192a988e10ca04845e205ea8582926af"
> meta-tpm2-dl = "master-wr:1fb0ab512da1e4cd28fddd87ab9aa71b5ad18911"
> wrlinux-dl = "master-wr:9a8ee391bed178c6edc275801806f3bab4e943c2"
> meta-tpm-dl = "master-wr:a714909ea084fdb903c952f9d12036b720c57d30"
> wrlinux-ovp-dl = "master-wr:b977985e906d8eebad4d84ac0d58e0f025f7cd48"
> meta-cgl-common-dl = "master-wr:0e28920fa54ef3669ef254598376b8be17a8fc5c"
> wrlinux-cgl-dl = "master-wr:347aa204485d9f7f5aeb839c79ba0bb864f34898"
> meta-intel-dl = "master-wr:cf052f5407a4797b157a5fa05964c9190538749f"
> meta-dpdk-dl = "master-wr:41b69bd8b5299303d4b58847d1c3761f68c27b38"
> meta-intel-qat-dl = "master-wr:6076ccac2211ad64a4640fd1665c61ed577932a2"
> meta-anaconda-dl = "master-wr:fe6dff64ca70491e762fa53ffea8099a70258b9a"
> intel-socfpga-dl = "master-wr:1f850e1ad9c9d607a5e07703f730baa3a8f01c23"
> meta-signing-key-dl = "master-wr:e4af4df72d5f6b0a9f561bc631bb8dde30f5715c"
> meta-overc-dl = "master-wr:57300911316b043bbd665f129213cb61a862dffe"
> meta-cloud-services-dl-2.7 = "master-wr:fa850191b711968d778e0eabd990d415eaa7b5e3"
> meta-filesystems-dl-2.7 = "master-wr:9142e7c86447011f116261d7339c7991ae886e21"
> meta-gnome-dl-2.7 = "master-wr:62544355e093b12dff8d23c491459db2295cb048"
> meta-gplv2-dl-2.7 = "master-wr:659295af85544c098037894c68f41cf2d5e5f66c"
> meta-initramfs-dl-2.7 = "master-wr:a478b17a139846430ee6ab5df979a18bcd78a7f7"
> meta-multimedia-dl-2.7 = "master-wr:627de73ccf29212ad522852450f843f968be706b"
> meta-networking-dl-2.7 = "master-wr:7cfe6581238402a8fc77a7fa792feb9b4dbef581"
> meta-oe-dl-2.7 = "master-wr:f94b042d5fbed4b90756c1bf6e9b4e38aa5d5302"
> meta-openstack-dl-2.7 = "master-wr:932feacb8c20a263da8ab3a5629da7a0fa0d0f2f"
> meta-perl-dl-2.7 = "master-wr:0ed5512cb5483208ea64200dbb767ef276b17e50"
> meta-python-dl-2.7 = "master-wr:c797ddb11da1c1f56735ac915b8156a9ccfced30"
> meta-realtime-dl-2.7 = "master-wr:9507da614b0e2899a7a6845642cff40a6590d524"
> meta-virtualization-dl-2.7 = "master-wr:05fae9d3dad2fefcc54d059c14a06ce0295140fa"
> meta-webserver-dl-2.7 = "master-wr:4d1835fde6680cfdb8ba25572c175d386f59d3cb"
> meta-xfce-dl-2.7 = "master-wr:5683cae374e8049f665de52b854a5ddab8193e24"
> oe-core-dl-2.7 = "master-wr:8872fc97aa6705b8dacdfa8ae3b6c0d5c6321ead"
> local = "master:3fb2dc44a72e070c40a71e041fc4dbc19b373ba6"
>
> ----------------------------------------------------------------------
> DISTRO wrlinux-std-sato is deprecated, use wrlinux-graphics instead.
> ----------------------------------------------------------------------
> Initialising tasks: 100% |##########################################################################################################################################################################| Time: 0:00:00
> Sstate summary: Wanted 0 Found 0 Missed 0 Current 48 (0% match, 100% complete)
> NOTE: Executing SetScene Tasks
> NOTE: Executing RunQueue Tasks
> Currently 1 running tasks (384 of 384) 99% |################################################################################################################################################################### |
> 0: linux-yocto-dev-5.2-rc++gitAUTOINC+8099163beb_7366c52b5f-r0 do_menuconfig - 0s (pid 32511)
> NOTE: Tasks Summary: Attempted 384 tasks of which 383 didn't need to be rerun and all succeeded.
>
> Summary: There were 5 WARNING messages shown.
> zchen at pek-lpggp4:$
>
> Arch built boot boardname
> -------------------------------------
> ARM64 y y xilinx-zynqmp
>
More information about the linux-yocto
mailing list