[meta-ti] [PATCH 1/2] u-boot 2011.09: convert beagleboard to SPL build
Koen Kooi
koen at dominion.thruhere.net
Tue Nov 29 04:21:32 PST 2011
Any objections to this series?
Op 27 nov. 2011, om 16:03 heeft Koen Kooi het volgende geschreven:
> Runtime tested on an xM rev C
>
> Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> ---
> ...-probe-DDC-bus-for-expansionboard-EEPROMS.patch | 165 ----------
> ...p3-mem-Comment-enable_gpmc_cs_config-more.patch | 56 ++++
> ...e-SDRC-dram_init-to-always-call-make_cs1_.patch | 66 ++++
> ...-a-helper-function-to-set-timings-in-SDRC.patch | 172 +++++++++++
> ...e-mem_ok-to-clear-again-after-reading-bac.patch | 30 ++
> .../0005-OMAP3-Remove-get_mem_type-prototype.patch | 28 ++
> .../0006-omap3-mem-Add-MCFG-helper-macro.patch | 97 ++++++
> ...d-optimal-SDRC-autorefresh-control-values.patch | 59 ++++
> ...x-all-Micron-memory-timing-parts-with-the.patch | 55 ++++
> ...ework-memory-initalization-and-devkit8000.patch | 174 +++++++++++
> ...OMAP3-SPL-Add-identify_nand_chip-function.patch | 142 +++++++++
> ...0011-OMAP3-Add-SPL-support-to-Beagleboard.patch | 315 +++++++++++++++++++
> .../0012-OMAP3-Add-SPL-support-to-omap3_evm.patch | 319 ++++++++++++++++++++
> .../2011.09/0013-AM3517-Add-SPL-support.patch | 150 +++++++++
> .../0014-AM3517-CraneBoard-Add-SPL-support.patch | 150 +++++++++
> ...beagleboard-config-disable-cache-for-USB.patch} | 12 +-
> ...6-beagleboard-config-enable-gpio-command.patch} | 10 +-
> ...-some-timeout-durations-for-MMC-and-EHCI.patch} | 14 +-
> ...rd-mount-rootfs-RO-instead-of-RW-at-boot.patch} | 16 +-
> ...eagleBoard-config-Really-switch-to-ttyO2.patch} | 18 +-
> ...leboard-add-support-for-TCT-Beacon-board.patch} | 20 +-
> ...add-support-for-scanning-loop-through-ex.patch} | 26 +-
> recipes-bsp/u-boot/u-boot_2011.09.bb | 37 ++-
> 23 files changed, 1901 insertions(+), 230 deletions(-)
> delete mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0001-beagleboard-probe-DDC-bus-for-expansionboard-EEPROMS.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0001-omap3-mem-Comment-enable_gpmc_cs_config-more.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0002-OMAP3-Update-SDRC-dram_init-to-always-call-make_cs1_.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0003-OMAP3-Add-a-helper-function-to-set-timings-in-SDRC.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0004-OMAP3-Change-mem_ok-to-clear-again-after-reading-bac.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0005-OMAP3-Remove-get_mem_type-prototype.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0006-omap3-mem-Add-MCFG-helper-macro.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0007-OMAP3-Add-optimal-SDRC-autorefresh-control-values.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0008-OMAP3-Suffix-all-Micron-memory-timing-parts-with-the.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0009-OMAP3-SPL-Rework-memory-initalization-and-devkit8000.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0010-OMAP3-SPL-Add-identify_nand_chip-function.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0011-OMAP3-Add-SPL-support-to-Beagleboard.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0012-OMAP3-Add-SPL-support-to-omap3_evm.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0013-AM3517-Add-SPL-support.patch
> create mode 100644 recipes-bsp/u-boot/u-boot/2011.09/0014-AM3517-CraneBoard-Add-SPL-support.patch
> rename recipes-bsp/u-boot/u-boot/2011.09/{0001-HACK-beagleboard-config-disable-cache-for-USB.patch => 0015-HACK-beagleboard-config-disable-cache-for-USB.patch} (75%)
> rename recipes-bsp/u-boot/u-boot/2011.09/{0002-beagleboard-config-enable-gpio-command.patch => 0016-beagleboard-config-enable-gpio-command.patch} (77%)
> rename recipes-bsp/u-boot/u-boot/2011.09/{0003-Increased-some-timeout-durations-for-MMC-and-EHCI.patch => 0017-Increased-some-timeout-durations-for-MMC-and-EHCI.patch} (72%)
> rename recipes-bsp/u-boot/u-boot/2011.09/{0003-beagleboard-mount-rootfs-RO-instead-of-RW-at-boot.patch => 0018-beagleboard-mount-rootfs-RO-instead-of-RW-at-boot.patch} (64%)
> rename recipes-bsp/u-boot/u-boot/2011.09/{0002-beagleboard-switch-to-ttyO2.patch => 0019-BeagleBoard-config-Really-switch-to-ttyO2.patch} (57%)
> rename recipes-bsp/u-boot/u-boot/2011.09/{0001-beagleboard-add-support-for-TCT-Beacon-board.patch => 0020-beagleboard-add-support-for-TCT-Beacon-board.patch} (81%)
> rename recipes-bsp/u-boot/u-boot/2011.09/{0001-beagleboard-add-support-for-scanning-loop-through-ex.patch => 0021-beagleboard-add-support-for-scanning-loop-through-ex.patch} (83%)
>
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0001-beagleboard-probe-DDC-bus-for-expansionboard-EEPROMS.patch b/recipes-bsp/u-boot/u-boot/2011.09/0001-beagleboard-probe-DDC-bus-for-expansionboard-EEPROMS.patch
> deleted file mode 100644
> index 4155d29..0000000
> --- a/recipes-bsp/u-boot/u-boot/2011.09/0001-beagleboard-probe-DDC-bus-for-expansionboard-EEPROMS.patch
> +++ /dev/null
> @@ -1,165 +0,0 @@
> -From 559eb0f547267df0706d283974916b88d6b9fb7d Mon Sep 17 00:00:00 2001
> -From: Koen Kooi <koen at dominion.thruhere.net>
> -Date: Sun, 9 Oct 2011 15:55:05 +0200
> -Subject: [PATCH] beagleboard: probe DDC bus for expansionboard EEPROMS as well
> -
> -Add beacon support as well, needs to get split into a seperate patch
> -
> -Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> ----
> - board/ti/beagle/beagle.c | 59 ++++++++++++++++++++++++++++++++++++++++
> - board/ti/beagle/beagle.h | 7 +++++
> - include/configs/omap3_beagle.h | 7 +++++
> - 3 files changed, 73 insertions(+), 0 deletions(-)
> -
> -diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c
> -index 8cdceaf..f4e986c 100644
> ---- a/board/ti/beagle/beagle.c
> -+++ b/board/ti/beagle/beagle.c
> -@@ -57,11 +57,14 @@ extern volatile struct ehci_hcor *hcor;
> - #define TWL4030_I2C_BUS 0
> - #define EXPANSION_EEPROM_I2C_BUS 1
> - #define EXPANSION_EEPROM_I2C_ADDRESS 0x50
> -+#define DVI_EDID_I2C_BUS 2
> -+#define DVI_EDID_I2C_ADDRESS 0x50
> -
> - #define TINCANTOOLS_ZIPPY 0x01000100
> - #define TINCANTOOLS_ZIPPY2 0x02000100
> - #define TINCANTOOLS_TRAINER 0x04000100
> - #define TINCANTOOLS_SHOWDOG 0x03000100
> -+#define TINCANTOOLS_BEACON 0x05000100
> - #define KBADC_BEAGLEFPGA 0x01000600
> - #define LW_BEAGLETOUCH 0x01000700
> - #define BRAINMUX_LCDOG 0x01000800
> -@@ -69,6 +72,7 @@ extern volatile struct ehci_hcor *hcor;
> - #define BBTOYS_WIFI 0x01000B00
> - #define BBTOYS_VGA 0x02000B00
> - #define BBTOYS_LCD 0x03000B00
> -+#define BBTOYS_ULCD 0x04000B00
> - #define BEAGLE_NO_EEPROM 0xffffffff
> -
> - DECLARE_GLOBAL_DATA_PTR;
> -@@ -82,6 +86,16 @@ static struct {
> - char env_setting[64];
> - } expansion_config;
> -
> -+static struct {
> -+ unsigned int device_vendor;
> -+ unsigned char revision;
> -+ unsigned char content;
> -+ char fab_revision[8];
> -+ char env_var[16];
> -+ char env_setting[64];
> -+} edid_config;
> -+
> -+
> - /*
> - * Routine: board_init
> - * Description: Early hardware init.
> -@@ -165,6 +179,33 @@ unsigned int get_expansion_id(void)
> - }
> -
> - /*
> -+ * Routine: get_edid
> -+ * Description: This function checks for expansion board by checking I2C
> -+ * bus 2 for the availability of an EEPROM
> -+ * returns the device_vendor field from the EEPROM
> -+ * The content can be either real EDID data or expansionboard data.
> -+ * Only expansionboar data is currently supported
> -+ */
> -+unsigned int get_edid(void)
> -+{
> -+ i2c_set_bus_num(DVI_EDID_I2C_BUS);
> -+
> -+ /* return BEAGLE_NO_EEPROM if eeprom doesn't respond */
> -+ if (i2c_probe(DVI_EDID_I2C_ADDRESS) == 1) {
> -+ i2c_set_bus_num(TWL4030_I2C_BUS);
> -+ return BEAGLE_NO_EEPROM;
> -+ }
> -+
> -+ /* read EEPROM data */
> -+ i2c_read(DVI_EDID_I2C_ADDRESS, 0, 1, (u8 *)&edid_config,
> -+ sizeof(edid_config));
> -+
> -+ i2c_set_bus_num(TWL4030_I2C_BUS);
> -+
> -+ return edid_config.device_vendor;
> -+}
> -+
> -+/*
> - * Configure DSS to display background color on DVID
> - * Configure VENC to display color bar on S-Video
> - */
> -@@ -290,6 +331,13 @@ int misc_init_r(void)
> - setenv("defaultdisplay", "showdoglcd");
> - setenv("buddy", "showdog");
> - break;
> -+ case TINCANTOOLS_BEACON:
> -+ printf("Recognized Tincantools Beacon board (rev %d %s)\n",
> -+ expansion_config.revision,
> -+ expansion_config.fab_revision);
> -+ MUX_TINCANTOOLS_BEACON();
> -+ setenv("buddy", "beacon");
> -+ break;
> - case KBADC_BEAGLEFPGA:
> - printf("Recognized KBADC Beagle FPGA board\n");
> - MUX_KBADC_BEAGLEFPGA();
> -@@ -331,6 +379,17 @@ int misc_init_r(void)
> - if (expansion_config.content == 1)
> - setenv(expansion_config.env_var, expansion_config.env_setting);
> -
> -+ switch(get_edid()) {
> -+ case BBTOYS_ULCD:
> -+ printf("Recognized BeagleBoardToys universal LCD board on DDC bus\n");
> -+ setenv("edid", "uLCD");
> -+ break;
> -+ default:
> -+ printf("Unrecognized EEPROM content on DDC bus: %x\n",
> -+ edid_config.device_vendor);
> -+ setenv("edid", "unknown");
> -+ }
> -+
> - twl4030_power_init();
> - switch (get_board_revision()) {
> - case REVISION_XM_A:
> -diff --git a/board/ti/beagle/beagle.h b/board/ti/beagle/beagle.h
> -index 18bfaa8..6a9ad73 100644
> ---- a/board/ti/beagle/beagle.h
> -+++ b/board/ti/beagle/beagle.h
> -@@ -456,6 +456,13 @@ const omap3_sysinfo sysinfo = {
> - MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTU | EN | M4)) /*GPIO_141*/\
> - MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTU | EN | M4)) /*GPIO_162*/
> -
> -+#define MUX_TINCANTOOLS_BEACON() \
> -+ MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M4)) /*GPIO_135*/\
> -+ MUX_VAL(CP(MMC2_DAT4), (IEN | PTU | EN | M4)) /*GPIO_136*/\
> -+ MUX_VAL(CP(MMC2_DAT5), (IEN | PTU | EN | M4)) /*GPIO_137*/\
> -+ MUX_VAL(CP(MMC2_DAT6), (IEN | PTU | EN | M4)) /*GPIO_138*/\
> -+ MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M4)) /*GPIO_139*/\
> -+
> - #define MUX_KBADC_BEAGLEFPGA() \
> - MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTU | DIS | M1)) /*MCSPI4_CLK*/\
> - MUX_VAL(CP(MCBSP1_DX), (IDIS | PTU | DIS | M1)) /*MCSPI4_SIMO*/\
> -diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
> -index 1369c89..73df658 100644
> ---- a/include/configs/omap3_beagle.h
> -+++ b/include/configs/omap3_beagle.h
> -@@ -219,6 +224,7 @@
> - "console=ttyS2,115200n8\0" \
> - "mpurate=auto\0" \
> - "buddy=none "\
> -+ "edid=none "\
> - "optargs=\0" \
> - "camera=none\0" \
> - "vram=12M\0" \
> -@@ -235,6 +241,7 @@
> - "${optargs} " \
> - "mpurate=${mpurate} " \
> - "buddy=${buddy} "\
> -+ "edid=${edid} "\
> - "camera=${camera} "\
> - "vram=${vram} " \
> - "omapfb.mode=dvi:${dvimode} " \
> ---
> -1.6.6.1
> -
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0001-omap3-mem-Comment-enable_gpmc_cs_config-more.patch b/recipes-bsp/u-boot/u-boot/2011.09/0001-omap3-mem-Comment-enable_gpmc_cs_config-more.patch
> new file mode 100644
> index 0000000..38da967
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0001-omap3-mem-Comment-enable_gpmc_cs_config-more.patch
> @@ -0,0 +1,56 @@
> +From 81630b54970a9274140b1c14caa31da6331a62fa Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:47:58 +0000
> +Subject: [PATCH 01/21] omap3: mem: Comment enable_gpmc_cs_config more
> +
> +Expand the "enable the config" comment to explain what the bit shifts
> +are and define out two of the magic numbers.
> +
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + arch/arm/cpu/armv7/omap3/mem.c | 12 +++++++++---
> + arch/arm/include/asm/arch-omap3/mem.h | 4 ++++
> + 2 files changed, 13 insertions(+), 3 deletions(-)
> +
> +diff --git a/arch/arm/cpu/armv7/omap3/mem.c b/arch/arm/cpu/armv7/omap3/mem.c
> +index a01c303..2f1efea 100644
> +--- a/arch/arm/cpu/armv7/omap3/mem.c
> ++++ b/arch/arm/cpu/armv7/omap3/mem.c
> +@@ -105,9 +105,15 @@ void enable_gpmc_cs_config(const u32 *gpmc_config, struct gpmc_cs *cs, u32 base,
> + writel(gpmc_config[3], &cs->config4);
> + writel(gpmc_config[4], &cs->config5);
> + writel(gpmc_config[5], &cs->config6);
> +- /* Enable the config */
> +- writel((((size & 0xF) << 8) | ((base >> 24) & 0x3F) |
> +- (1 << 6)), &cs->config7);
> ++
> ++ /*
> ++ * Enable the config. size is the CS size and goes in
> ++ * bits 11:8. We set bit 6 to enable this CS and the base
> ++ * address goes into bits 5:0.
> ++ */
> ++ writel((size << 8) | (GPMC_CS_ENABLE << 6) |
> ++ ((base >> 24) & GPMC_BASEADDR_MASK),
> ++ &cs->config7);
> + sdelay(2000);
> + }
> +
> +diff --git a/arch/arm/include/asm/arch-omap3/mem.h b/arch/arm/include/asm/arch-omap3/mem.h
> +index db6a696..abf4e82 100644
> +--- a/arch/arm/include/asm/arch-omap3/mem.h
> ++++ b/arch/arm/include/asm/arch-omap3/mem.h
> +@@ -259,6 +259,10 @@ enum {
> + #define GPMC_SIZE_32M 0xE
> + #define GPMC_SIZE_16M 0xF
> +
> ++#define GPMC_BASEADDR_MASK 0x3F
> ++
> ++#define GPMC_CS_ENABLE 0x1
> ++
> + #define SMNAND_GPMC_CONFIG1 0x00000800
> + #define SMNAND_GPMC_CONFIG2 0x00141400
> + #define SMNAND_GPMC_CONFIG3 0x00141400
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0002-OMAP3-Update-SDRC-dram_init-to-always-call-make_cs1_.patch b/recipes-bsp/u-boot/u-boot/2011.09/0002-OMAP3-Update-SDRC-dram_init-to-always-call-make_cs1_.patch
> new file mode 100644
> index 0000000..cb12873
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0002-OMAP3-Update-SDRC-dram_init-to-always-call-make_cs1_.patch
> @@ -0,0 +1,66 @@
> +From 42db3ebdd76628017e7ab83752e9b288ec4f26a0 Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:47:59 +0000
> +Subject: [PATCH 02/21] OMAP3: Update SDRC dram_init to always call make_cs1_contiguous()
> +
> +We update the comment in make_cs1_contiguous() to be a little bit
> +more clear (it's been copy/pasted from other silicons) and then
> +explain in dram_init() why we need to always try this.
> +
> +Note that in the previous behavior we were always calling this on
> +boards that never had cs1 populated anyhow so making sure we do
> +this always is fine and will correct things like omap3evm detecting
> +an invalid amount of memory (384MB).
> +
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + arch/arm/cpu/armv7/omap3/sdrc.c | 23 +++++++++++------------
> + 1 files changed, 11 insertions(+), 12 deletions(-)
> +
> +diff --git a/arch/arm/cpu/armv7/omap3/sdrc.c b/arch/arm/cpu/armv7/omap3/sdrc.c
> +index 0dd1955..66ce33f 100644
> +--- a/arch/arm/cpu/armv7/omap3/sdrc.c
> ++++ b/arch/arm/cpu/armv7/omap3/sdrc.c
> +@@ -58,10 +58,9 @@ u32 is_mem_sdr(void)
> +
> + /*
> + * make_cs1_contiguous -
> +- * - For es2 and above remap cs1 behind cs0 to allow command line
> +- * mem=xyz use all memory with out discontinuous support compiled in.
> +- * Could do it at the ATAG, but there really is two banks...
> +- * - Called as part of 2nd phase DDR init.
> ++ * - When we have CS1 populated we want to have it mapped after cs0 to allow
> ++ * command line mem=xyz use all memory with out discontinuous support
> ++ * compiled in. We could do it in the ATAG, but there really is two banks...
> + */
> + void make_cs1_contiguous(void)
> + {
> +@@ -207,16 +206,16 @@ int dram_init(void)
> +
> + size0 = get_sdr_cs_size(CS0);
> + /*
> +- * If a second bank of DDR is attached to CS1 this is
> +- * where it can be started. Early init code will init
> +- * memory on CS0.
> ++ * We always need to have cs_cfg point at where the second
> ++ * bank would be, if present. Failure to do so can lead to
> ++ * strange situations where memory isn't detected and
> ++ * configured correctly. CS0 will already have been setup
> ++ * at this point.
> + */
> +- if ((sysinfo.mtype == DDR_COMBO) || (sysinfo.mtype == DDR_STACKED)) {
> +- do_sdrc_init(CS1, NOT_EARLY);
> +- make_cs1_contiguous();
> ++ make_cs1_contiguous();
> ++ do_sdrc_init(CS1, NOT_EARLY);
> ++ size1 = get_sdr_cs_size(CS1);
> +
> +- size1 = get_sdr_cs_size(CS1);
> +- }
> + gd->ram_size = size0 + size1;
> +
> + return 0;
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0003-OMAP3-Add-a-helper-function-to-set-timings-in-SDRC.patch b/recipes-bsp/u-boot/u-boot/2011.09/0003-OMAP3-Add-a-helper-function-to-set-timings-in-SDRC.patch
> new file mode 100644
> index 0000000..71e49af
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0003-OMAP3-Add-a-helper-function-to-set-timings-in-SDRC.patch
> @@ -0,0 +1,172 @@
> +From a186210c5003db4df2a4f97bd6d4cb2dc616a591 Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:48:00 +0000
> +Subject: [PATCH 03/21] OMAP3: Add a helper function to set timings in SDRC
> +
> +Since we go through the sequence to setup the SDRC timings more than
> +once, break this logic out into its own function and have that function
> +call mem_ok() to make sure the memory is usable.
> +
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + arch/arm/cpu/armv7/omap3/sdrc.c | 116 ++++++++++++++++++++------------------
> + 1 files changed, 61 insertions(+), 55 deletions(-)
> +
> +diff --git a/arch/arm/cpu/armv7/omap3/sdrc.c b/arch/arm/cpu/armv7/omap3/sdrc.c
> +index 66ce33f..2756024 100644
> +--- a/arch/arm/cpu/armv7/omap3/sdrc.c
> ++++ b/arch/arm/cpu/armv7/omap3/sdrc.c
> +@@ -108,14 +108,45 @@ u32 get_sdr_cs_offset(u32 cs)
> + }
> +
> + /*
> ++ * write_sdrc_timings -
> ++ * - Takes CS and associated timings and initalize SDRAM
> ++ * - Test CS to make sure it's OK for use
> ++ */
> ++static void write_sdrc_timings(u32 cs, struct sdrc_actim *sdrc_actim_base,
> ++ u32 mcfg, u32 ctrla, u32 ctrlb, u32 rfr_ctrl, u32 mr)
> ++{
> ++ /* Setup timings we got from the board. */
> ++ writel(mcfg, &sdrc_base->cs[cs].mcfg);
> ++ writel(ctrla, &sdrc_actim_base->ctrla);
> ++ writel(ctrlb, &sdrc_actim_base->ctrlb);
> ++ writel(rfr_ctrl, &sdrc_base->cs[cs].rfr_ctrl);
> ++ writel(CMD_NOP, &sdrc_base->cs[cs].manual);
> ++ writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
> ++ writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
> ++ writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
> ++ writel(mr, &sdrc_base->cs[cs].mr);
> ++
> ++ /*
> ++ * Test ram in this bank
> ++ * Disable if bad or not present
> ++ */
> ++ if (!mem_ok(cs))
> ++ writel(0, &sdrc_base->cs[cs].mcfg);
> ++}
> ++
> ++/*
> + * do_sdrc_init -
> +- * - Initialize the SDRAM for use.
> +- * - code called once in C-Stack only context for CS0 and a possible 2nd
> +- * time depending on memory configuration from stack+global context
> ++ * - Code called once in C-Stack only context for CS0 and with early being
> ++ * true and a possible 2nd time depending on memory configuration from
> ++ * stack+global context.
> + */
> + void do_sdrc_init(u32 cs, u32 early)
> + {
> + struct sdrc_actim *sdrc_actim_base0, *sdrc_actim_base1;
> ++ u32 mcfg, ctrla, ctrlb, rfr_ctrl, mr;
> ++
> ++ sdrc_actim_base0 = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
> ++ sdrc_actim_base1 = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
> +
> + if (early) {
> + /* reset sdrc controller */
> +@@ -127,73 +158,48 @@ void do_sdrc_init(u32 cs, u32 early)
> + /* setup sdrc to ball mux */
> + writel(SDRC_SHARING, &sdrc_base->sharing);
> +
> +- /* Disable Power Down of CKE cuz of 1 CKE on combo part */
> ++ /* Disable Power Down of CKE because of 1 CKE on combo part */
> + writel(WAKEUPPROC | SRFRONRESET | PAGEPOLICY_HIGH,
> + &sdrc_base->power);
> +
> + writel(ENADLL | DLLPHASE_90, &sdrc_base->dlla_ctrl);
> + sdelay(0x20000);
> +- }
> +-
> + /* As long as V_MCFG and V_RFR_CTRL is not defined for all OMAP3 boards we need
> + * to prevent this to be build in non-SPL build */
> + #ifdef CONFIG_SPL_BUILD
> +- /* If we use a SPL there is no x-loader nor config header so we have
> +- * to do the job ourselfs
> +- */
> +- if (cs == CS0) {
> +- sdrc_actim_base0 = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
> +-
> +- /* General SDRC config */
> +- writel(V_MCFG, &sdrc_base->cs[cs].mcfg);
> +- writel(V_RFR_CTRL, &sdrc_base->cs[cs].rfr_ctrl);
> +-
> +- /* AC timings */
> +- writel(V_ACTIMA_165, &sdrc_actim_base0->ctrla);
> +- writel(V_ACTIMB_165, &sdrc_actim_base0->ctrlb);
> +-
> +- /* Initialize */
> +- writel(CMD_NOP, &sdrc_base->cs[cs].manual);
> +- writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
> +- writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
> +- writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
> ++ /*
> ++ * If we use a SPL there is no x-loader nor config header so
> ++ * we have to do the job ourselfs
> ++ */
> ++
> ++ mcfg = V_MCFG;
> ++ ctrla = V_ACTIMA_165;
> ++ ctrlb = V_ACTIMB_165;
> ++ rfr_ctrl = V_RFR_CTRL;
> ++ mr = V_MR;
> ++
> ++ write_sdrc_timings(CS0, sdrc_actim_base0, mcfg, ctrla, ctrlb,
> ++ rfr_ctrl, mr);
> ++#endif
> +
> +- writel(V_MR, &sdrc_base->cs[cs].mr);
> + }
> +-#endif
> +
> + /*
> +- * SDRC timings are set up by x-load or config header
> +- * We don't need to redo them here.
> +- * Older x-loads configure only CS0
> +- * configure CS1 to handle this ommission
> ++ * If we aren't using SPL we have been loaded by some
> ++ * other means which may not have correctly initialized
> ++ * both CS0 and CS1 (such as some older versions of x-loader)
> ++ * so we may be asked now to setup CS1.
> + */
> + if (cs == CS1) {
> +- sdrc_actim_base0 = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
> +- sdrc_actim_base1 = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
> +- writel(readl(&sdrc_base->cs[CS0].mcfg),
> +- &sdrc_base->cs[CS1].mcfg);
> +- writel(readl(&sdrc_base->cs[CS0].rfr_ctrl),
> +- &sdrc_base->cs[CS1].rfr_ctrl);
> +- writel(readl(&sdrc_actim_base0->ctrla),
> +- &sdrc_actim_base1->ctrla);
> +- writel(readl(&sdrc_actim_base0->ctrlb),
> +- &sdrc_actim_base1->ctrlb);
> +-
> +- writel(CMD_NOP, &sdrc_base->cs[cs].manual);
> +- writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
> +- writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
> +- writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
> +- writel(readl(&sdrc_base->cs[CS0].mr),
> +- &sdrc_base->cs[CS1].mr);
> +- }
> ++ mcfg = readl(&sdrc_base->cs[CS0].mcfg),
> ++ rfr_ctrl = readl(&sdrc_base->cs[CS0].rfr_ctrl);
> ++ ctrla = readl(&sdrc_actim_base0->ctrla),
> ++ ctrlb = readl(&sdrc_actim_base0->ctrlb);
> ++ mr = readl(&sdrc_base->cs[CS0].mr);
> ++ write_sdrc_timings(cs, sdrc_actim_base1, mcfg, ctrla, ctrlb,
> ++ rfr_ctrl, mr);
> +
> +- /*
> +- * Test ram in this bank
> +- * Disable if bad or not present
> +- */
> +- if (!mem_ok(cs))
> +- writel(0, &sdrc_base->cs[cs].mcfg);
> ++ }
> + }
> +
> + /*
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0004-OMAP3-Change-mem_ok-to-clear-again-after-reading-bac.patch b/recipes-bsp/u-boot/u-boot/2011.09/0004-OMAP3-Change-mem_ok-to-clear-again-after-reading-bac.patch
> new file mode 100644
> index 0000000..30d912c
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0004-OMAP3-Change-mem_ok-to-clear-again-after-reading-bac.patch
> @@ -0,0 +1,30 @@
> +From 0cf0d611823f6e1f3b63f9233c145a3940a89694 Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:48:01 +0000
> +Subject: [PATCH 04/21] OMAP3: Change mem_ok to clear again after reading back
> +
> +It's possible to need to call this function on the same banks multiple
> +times so we want to be sure that 'pos A' is cleared out again at the
> +end.
> +
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + arch/arm/cpu/armv7/omap3/mem.c | 1 +
> + 1 files changed, 1 insertions(+), 0 deletions(-)
> +
> +diff --git a/arch/arm/cpu/armv7/omap3/mem.c b/arch/arm/cpu/armv7/omap3/mem.c
> +index 2f1efea..2fe5ac7 100644
> +--- a/arch/arm/cpu/armv7/omap3/mem.c
> ++++ b/arch/arm/cpu/armv7/omap3/mem.c
> +@@ -86,6 +86,7 @@ u32 mem_ok(u32 cs)
> + writel(0x0, addr + 4); /* remove pattern off the bus */
> + val1 = readl(addr + 0x400); /* get pos A value */
> + val2 = readl(addr); /* get val2 */
> ++ writel(0x0, addr + 0x400); /* clear pos A */
> +
> + if ((val1 != 0) || (val2 != pattern)) /* see if pos A val changed */
> + return 0;
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0005-OMAP3-Remove-get_mem_type-prototype.patch b/recipes-bsp/u-boot/u-boot/2011.09/0005-OMAP3-Remove-get_mem_type-prototype.patch
> new file mode 100644
> index 0000000..ec1b5f7
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0005-OMAP3-Remove-get_mem_type-prototype.patch
> @@ -0,0 +1,28 @@
> +From 45ccdf2ba3aa6e5f258c463691c85ac4529246e6 Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:48:02 +0000
> +Subject: [PATCH 05/21] OMAP3: Remove get_mem_type prototype
> +
> +This function doesn't exist for omap3
> +
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + arch/arm/include/asm/arch-omap3/sys_proto.h | 1 -
> + 1 files changed, 0 insertions(+), 1 deletions(-)
> +
> +diff --git a/arch/arm/include/asm/arch-omap3/sys_proto.h b/arch/arm/include/asm/arch-omap3/sys_proto.h
> +index 995e7cb..9e64410 100644
> +--- a/arch/arm/include/asm/arch-omap3/sys_proto.h
> ++++ b/arch/arm/include/asm/arch-omap3/sys_proto.h
> +@@ -49,7 +49,6 @@ void set_muxconf_regs(void);
> + u32 get_cpu_family(void);
> + u32 get_cpu_rev(void);
> + u32 get_sku_id(void);
> +-u32 get_mem_type(void);
> + u32 get_sysboot_value(void);
> + u32 is_gpmc_muxed(void);
> + u32 get_gpmc0_type(void);
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0006-omap3-mem-Add-MCFG-helper-macro.patch b/recipes-bsp/u-boot/u-boot/2011.09/0006-omap3-mem-Add-MCFG-helper-macro.patch
> new file mode 100644
> index 0000000..475febf
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0006-omap3-mem-Add-MCFG-helper-macro.patch
> @@ -0,0 +1,97 @@
> +From bd50b147ff61a5203815296eac726b0a244c3cb2 Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:48:03 +0000
> +Subject: [PATCH 06/21] omap3: mem: Add MCFG helper macro
> +
> +This adds an MCFG macro to calculate the correct value, similar to
> +the ACTIMA/ACTIMB macros and adds a comment that all of the potential
> +values here are documented in the TRM. Then we convert the Micron
> +value to use this macro.
> +
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + arch/arm/include/asm/arch-omap3/mem.h | 46 +++++++++++++++++++++-----------
> + 1 files changed, 30 insertions(+), 16 deletions(-)
> +
> +diff --git a/arch/arm/include/asm/arch-omap3/mem.h b/arch/arm/include/asm/arch-omap3/mem.h
> +index abf4e82..12ff3b0 100644
> +--- a/arch/arm/include/asm/arch-omap3/mem.h
> ++++ b/arch/arm/include/asm/arch-omap3/mem.h
> +@@ -39,6 +39,12 @@ enum {
> +
> + #define EARLY_INIT 1
> +
> ++/*
> ++ * For a full explanation of these registers and values please see
> ++ * the Technical Reference Manual (TRM) for any of the processors in
> ++ * this family.
> ++ */
> ++
> + /* Slower full frequency range default timings for x32 operation*/
> + #define SDRC_SHARING 0x00000100
> + #define SDRC_MR_0_SDR 0x00000031
> +@@ -86,6 +92,27 @@ enum {
> + ACTIM_CTRLB_TXP(b) | \
> + ACTIM_CTRLB_TXSR(d)
> +
> ++/*
> ++ * Values used in the MCFG register. Only values we use today
> ++ * are defined and the rest can be found in the TRM. Unless otherwise
> ++ * noted all fields are one bit.
> ++ */
> ++#define V_MCFG_RAMTYPE_DDR (0x1)
> ++#define V_MCFG_DEEPPD_EN (0x1 << 3)
> ++#define V_MCFG_B32NOT16_32 (0x1 << 4)
> ++#define V_MCFG_BANKALLOCATION_RBC (0x2 << 6) /* 6:7 */
> ++#define V_MCFG_RAMSIZE(a) ((((a)/(1024*1024))/2) << 8) /* 8:17 */
> ++#define V_MCFG_ADDRMUXLEGACY_FLEX (0x1 << 19)
> ++#define V_MCFG_CASWIDTH_10B (0x5 << 20) /* 20:22 */
> ++#define V_MCFG_RASWIDTH(a) ((a) << 24) /* 24:26 */
> ++
> ++/* Macro to construct MCFG */
> ++#define MCFG(a, b) \
> ++ V_MCFG_RASWIDTH(b) | V_MCFG_CASWIDTH_10B | \
> ++ V_MCFG_ADDRMUXLEGACY_FLEX | V_MCFG_RAMSIZE(a) | \
> ++ V_MCFG_BANKALLOCATION_RBC | \
> ++ V_MCFG_B32NOT16_32 | V_MCFG_DEEPPD_EN | V_MCFG_RAMTYPE_DDR
> ++
> + /* Infineon part of 3430SDP (165MHz optimized) 6.06ns */
> + #define INFINEON_TDAL_165 6 /* Twr/Tck + Trp/tck */
> + /* 15/6 + 18/6 = 5.5 -> 6 */
> +@@ -138,21 +165,8 @@ enum {
> + ACTIM_CTRLB(MICRON_TWTR_165, MICRON_TCKE_165, \
> + MICRON_TXP_165, MICRON_XSR_165)
> +
> +-#define MICRON_RAMTYPE 0x1
> +-#define MICRON_DDRTYPE 0x0
> +-#define MICRON_DEEPPD 0x1
> +-#define MICRON_B32NOT16 0x1
> +-#define MICRON_BANKALLOCATION 0x2
> +-#define MICRON_RAMSIZE ((PHYS_SDRAM_1_SIZE/(1024*1024))/2)
> +-#define MICRON_ADDRMUXLEGACY 0x1
> +-#define MICRON_CASWIDTH 0x5
> +-#define MICRON_RASWIDTH 0x2
> +-#define MICRON_LOCKSTATUS 0x0
> +-#define MICRON_V_MCFG ((MICRON_LOCKSTATUS << 30) | (MICRON_RASWIDTH << 24) | \
> +- (MICRON_CASWIDTH << 20) | (MICRON_ADDRMUXLEGACY << 19) | \
> +- (MICRON_RAMSIZE << 8) | (MICRON_BANKALLOCATION << 6) | \
> +- (MICRON_B32NOT16 << 4) | (MICRON_DEEPPD << 3) | \
> +- (MICRON_DDRTYPE << 2) | (MICRON_RAMTYPE))
> ++#define MICRON_RASWIDTH 0x2
> ++#define MICRON_V_MCFG(size) MCFG((size), MICRON_RASWIDTH)
> +
> + #define MICRON_ARCV 2030
> + #define MICRON_ARE 0x1
> +@@ -199,7 +213,7 @@ enum {
> + #ifdef CONFIG_OMAP3_MICRON_DDR
> + #define V_ACTIMA_165 MICRON_V_ACTIMA_165
> + #define V_ACTIMB_165 MICRON_V_ACTIMB_165
> +-#define V_MCFG MICRON_V_MCFG
> ++#define V_MCFG MICRON_V_MCFG(PHYS_SDRAM_1_SIZE)
> + #define V_RFR_CTRL MICRON_V_RFR_CTRL
> + #define V_MR MICRON_V_MR
> + #endif
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0007-OMAP3-Add-optimal-SDRC-autorefresh-control-values.patch b/recipes-bsp/u-boot/u-boot/2011.09/0007-OMAP3-Add-optimal-SDRC-autorefresh-control-values.patch
> new file mode 100644
> index 0000000..2024094
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0007-OMAP3-Add-optimal-SDRC-autorefresh-control-values.patch
> @@ -0,0 +1,59 @@
> +From 67ea79f7a99d7168915a5db8a577814ec501774e Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:48:04 +0000
> +Subject: [PATCH 07/21] OMAP3: Add optimal SDRC autorefresh control values
> +
> +This adds the optimal SDRC autorefresh control register values for
> +100Mhz, 133MHz, 165MHz and 200MHz clocks. We switch to using this
> +to provide the default 165MHz value.
> +
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + arch/arm/include/asm/arch-omap3/mem.h | 16 +++++++++++-----
> + 1 files changed, 11 insertions(+), 5 deletions(-)
> +
> +diff --git a/arch/arm/include/asm/arch-omap3/mem.h b/arch/arm/include/asm/arch-omap3/mem.h
> +index 12ff3b0..912c737 100644
> +--- a/arch/arm/include/asm/arch-omap3/mem.h
> ++++ b/arch/arm/include/asm/arch-omap3/mem.h
> +@@ -49,6 +49,16 @@ enum {
> + #define SDRC_SHARING 0x00000100
> + #define SDRC_MR_0_SDR 0x00000031
> +
> ++/*
> ++ * SDRC autorefresh control values. This register consists of autorefresh
> ++ * enable at bits 0:1 and an autorefresh counter value in bits 8:23. The
> ++ * counter is a result of ( tREFI / tCK ) - 50.
> ++ */
> ++#define SDP_3430_SDRC_RFR_CTRL_100MHz 0x0002da01
> ++#define SDP_3430_SDRC_RFR_CTRL_133MHz 0x0003de01 /* 7.8us/7.5ns - 50=0x3de */
> ++#define SDP_3430_SDRC_RFR_CTRL_165MHz 0x0004e201 /* 7.8us/6ns - 50=0x4e2 */
> ++#define SDP_3430_SDRC_RFR_CTRL_200MHz 0x0005e601 /* 7.8us/5ns - 50=0x5e6 */
> ++
> + #define DLL_OFFSET 0
> + #define DLL_WRITEDDRCLKX2DIS 1
> + #define DLL_ENADLL 1
> +@@ -168,10 +178,6 @@ enum {
> + #define MICRON_RASWIDTH 0x2
> + #define MICRON_V_MCFG(size) MCFG((size), MICRON_RASWIDTH)
> +
> +-#define MICRON_ARCV 2030
> +-#define MICRON_ARE 0x1
> +-#define MICRON_V_RFR_CTRL ((MICRON_ARCV << 8) | (MICRON_ARE))
> +-
> + #define MICRON_BL 0x2
> + #define MICRON_SIL 0x0
> + #define MICRON_CASL 0x3
> +@@ -214,7 +220,7 @@ enum {
> + #define V_ACTIMA_165 MICRON_V_ACTIMA_165
> + #define V_ACTIMB_165 MICRON_V_ACTIMB_165
> + #define V_MCFG MICRON_V_MCFG(PHYS_SDRAM_1_SIZE)
> +-#define V_RFR_CTRL MICRON_V_RFR_CTRL
> ++#define V_RFR_CTRL SDP_3430_SDRC_RFR_CTRL_165MHz
> + #define V_MR MICRON_V_MR
> + #endif
> +
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0008-OMAP3-Suffix-all-Micron-memory-timing-parts-with-the.patch b/recipes-bsp/u-boot/u-boot/2011.09/0008-OMAP3-Suffix-all-Micron-memory-timing-parts-with-the.patch
> new file mode 100644
> index 0000000..79f4efb
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0008-OMAP3-Suffix-all-Micron-memory-timing-parts-with-the.patch
> @@ -0,0 +1,55 @@
> +From 0e9f4ab3cafdc1de638ab7a603a750acd4688967 Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:48:05 +0000
> +Subject: [PATCH 08/21] OMAP3: Suffix all Micron memory timing parts with their speed
> +
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + arch/arm/include/asm/arch-omap3/mem.h | 21 +++++++++++----------
> + 1 files changed, 11 insertions(+), 10 deletions(-)
> +
> +diff --git a/arch/arm/include/asm/arch-omap3/mem.h b/arch/arm/include/asm/arch-omap3/mem.h
> +index 912c737..4f996d9 100644
> +--- a/arch/arm/include/asm/arch-omap3/mem.h
> ++++ b/arch/arm/include/asm/arch-omap3/mem.h
> +@@ -175,15 +175,16 @@ enum {
> + ACTIM_CTRLB(MICRON_TWTR_165, MICRON_TCKE_165, \
> + MICRON_TXP_165, MICRON_XSR_165)
> +
> +-#define MICRON_RASWIDTH 0x2
> +-#define MICRON_V_MCFG(size) MCFG((size), MICRON_RASWIDTH)
> ++#define MICRON_RASWIDTH_165 0x2
> ++#define MICRON_V_MCFG_165(size) MCFG((size), MICRON_RASWIDTH_165)
> +
> +-#define MICRON_BL 0x2
> +-#define MICRON_SIL 0x0
> +-#define MICRON_CASL 0x3
> +-#define MICRON_WBST 0x0
> +-#define MICRON_V_MR ((MICRON_WBST << 9) | (MICRON_CASL << 4) | \
> +- (MICRON_SIL << 3) | (MICRON_BL))
> ++#define MICRON_BL_165 0x2
> ++#define MICRON_SIL_165 0x0
> ++#define MICRON_CASL_165 0x3
> ++#define MICRON_WBST_165 0x0
> ++#define MICRON_V_MR_165 ((MICRON_WBST_165 << 9) | \
> ++ (MICRON_CASL_165 << 4) | (MICRON_SIL_165 << 3) | \
> ++ (MICRON_BL_165))
> +
> + /* NUMONYX part of IGEP v2 (165MHz optimized) 6.06ns */
> + #define NUMONYX_TDAL_165 6 /* Twr/Tck + Trp/tck */
> +@@ -219,9 +220,9 @@ enum {
> + #ifdef CONFIG_OMAP3_MICRON_DDR
> + #define V_ACTIMA_165 MICRON_V_ACTIMA_165
> + #define V_ACTIMB_165 MICRON_V_ACTIMB_165
> +-#define V_MCFG MICRON_V_MCFG(PHYS_SDRAM_1_SIZE)
> ++#define V_MCFG MICRON_V_MCFG_165(PHYS_SDRAM_1_SIZE)
> + #define V_RFR_CTRL SDP_3430_SDRC_RFR_CTRL_165MHz
> +-#define V_MR MICRON_V_MR
> ++#define V_MR MICRON_V_MR_165
> + #endif
> +
> + #ifdef CONFIG_OMAP3_NUMONYX_DDR
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0009-OMAP3-SPL-Rework-memory-initalization-and-devkit8000.patch b/recipes-bsp/u-boot/u-boot/2011.09/0009-OMAP3-SPL-Rework-memory-initalization-and-devkit8000.patch
> new file mode 100644
> index 0000000..7c12e7a
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0009-OMAP3-SPL-Rework-memory-initalization-and-devkit8000.patch
> @@ -0,0 +1,174 @@
> +From bf66bbd9347874b6ad13f7747288327e968022d2 Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:48:06 +0000
> +Subject: [PATCH 09/21] OMAP3 SPL: Rework memory initalization and devkit8000 support
> +
> +This changes to making the board be responsible for providing the
> +memory initialization timings in SPL and converts the devkit8000
> +to this framework. In SPL we try and initialize both CS0 and CS1.
> +
> +Cc: Frederik Kriewitz <frederik at kriewitz.eu>
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + arch/arm/cpu/armv7/omap3/sdrc.c | 28 ++++++++++++++------------
> + arch/arm/include/asm/arch-omap3/mem.h | 26 -------------------------
> + arch/arm/include/asm/arch-omap3/sys_proto.h | 2 +
> + board/timll/devkit8000/devkit8000.c | 21 ++++++++++++++++++++
> + include/configs/devkit8000.h | 5 ----
> + 5 files changed, 38 insertions(+), 44 deletions(-)
> +
> +diff --git a/arch/arm/cpu/armv7/omap3/sdrc.c b/arch/arm/cpu/armv7/omap3/sdrc.c
> +index 2756024..a27b4b1 100644
> +--- a/arch/arm/cpu/armv7/omap3/sdrc.c
> ++++ b/arch/arm/cpu/armv7/omap3/sdrc.c
> +@@ -148,6 +148,18 @@ void do_sdrc_init(u32 cs, u32 early)
> + sdrc_actim_base0 = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
> + sdrc_actim_base1 = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
> +
> ++ /*
> ++ * When called in the early context this may be SPL and we will
> ++ * need to set all of the timings. This ends up being board
> ++ * specific so we call a helper function to take care of this
> ++ * for us. Otherwise, to be safe, we need to copy the settings
> ++ * from the first bank to the second. We will setup CS0,
> ++ * then set cs_cfg to the appropriate value then try and
> ++ * setup CS1.
> ++ */
> ++#ifdef CONFIG_SPL_BUILD
> ++ get_board_mem_timings(&mcfg, &ctrla, &ctrlb, &rfr_ctrl, &mr);
> ++#endif
> + if (early) {
> + /* reset sdrc controller */
> + writel(SOFTRESET, &sdrc_base->sysconfig);
> +@@ -164,22 +176,12 @@ void do_sdrc_init(u32 cs, u32 early)
> +
> + writel(ENADLL | DLLPHASE_90, &sdrc_base->dlla_ctrl);
> + sdelay(0x20000);
> +-/* As long as V_MCFG and V_RFR_CTRL is not defined for all OMAP3 boards we need
> +- * to prevent this to be build in non-SPL build */
> + #ifdef CONFIG_SPL_BUILD
> +- /*
> +- * If we use a SPL there is no x-loader nor config header so
> +- * we have to do the job ourselfs
> +- */
> +-
> +- mcfg = V_MCFG;
> +- ctrla = V_ACTIMA_165;
> +- ctrlb = V_ACTIMB_165;
> +- rfr_ctrl = V_RFR_CTRL;
> +- mr = V_MR;
> +-
> + write_sdrc_timings(CS0, sdrc_actim_base0, mcfg, ctrla, ctrlb,
> + rfr_ctrl, mr);
> ++ make_cs1_contiguous();
> ++ write_sdrc_timings(CS0, sdrc_actim_base1, mcfg, ctrla, ctrlb,
> ++ rfr_ctrl, mr);
> + #endif
> +
> + }
> +diff --git a/arch/arm/include/asm/arch-omap3/mem.h b/arch/arm/include/asm/arch-omap3/mem.h
> +index 4f996d9..09f5872 100644
> +--- a/arch/arm/include/asm/arch-omap3/mem.h
> ++++ b/arch/arm/include/asm/arch-omap3/mem.h
> +@@ -212,32 +212,6 @@ enum {
> + ACTIM_CTRLB(NUMONYX_TWTR_165, NUMONYX_TCKE_165, \
> + NUMONYX_TXP_165, NUMONYX_XSR_165)
> +
> +-#ifdef CONFIG_OMAP3_INFINEON_DDR
> +-#define V_ACTIMA_165 INFINEON_V_ACTIMA_165
> +-#define V_ACTIMB_165 INFINEON_V_ACTIMB_165
> +-#endif
> +-
> +-#ifdef CONFIG_OMAP3_MICRON_DDR
> +-#define V_ACTIMA_165 MICRON_V_ACTIMA_165
> +-#define V_ACTIMB_165 MICRON_V_ACTIMB_165
> +-#define V_MCFG MICRON_V_MCFG_165(PHYS_SDRAM_1_SIZE)
> +-#define V_RFR_CTRL SDP_3430_SDRC_RFR_CTRL_165MHz
> +-#define V_MR MICRON_V_MR_165
> +-#endif
> +-
> +-#ifdef CONFIG_OMAP3_NUMONYX_DDR
> +-#define V_ACTIMA_165 NUMONYX_V_ACTIMA_165
> +-#define V_ACTIMB_165 NUMONYX_V_ACTIMB_165
> +-#endif
> +-
> +-#if !defined(V_ACTIMA_165) || !defined(V_ACTIMB_165)
> +-#error "Please choose the right DDR type in config header"
> +-#endif
> +-
> +-#if defined(CONFIG_SPL_BUILD) && (!defined(V_MCFG) || !defined(V_RFR_CTRL))
> +-#error "Please choose the right DDR type in config header"
> +-#endif
> +-
> + /*
> + * GPMC settings -
> + * Definitions is as per the following format
> +diff --git a/arch/arm/include/asm/arch-omap3/sys_proto.h b/arch/arm/include/asm/arch-omap3/sys_proto.h
> +index 9e64410..80e167b 100644
> +--- a/arch/arm/include/asm/arch-omap3/sys_proto.h
> ++++ b/arch/arm/include/asm/arch-omap3/sys_proto.h
> +@@ -38,6 +38,8 @@ void per_clocks_enable(void);
> + void memif_init(void);
> + void sdrc_init(void);
> + void do_sdrc_init(u32, u32);
> ++void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
> ++ u32 *mr);
> + void emif4_init(void);
> + void gpmc_init(void);
> + void enable_gpmc_cs_config(const u32 *gpmc_config, struct gpmc_cs *cs, u32 base,
> +diff --git a/board/timll/devkit8000/devkit8000.c b/board/timll/devkit8000/devkit8000.c
> +index fee0dff..b06aab6 100644
> +--- a/board/timll/devkit8000/devkit8000.c
> ++++ b/board/timll/devkit8000/devkit8000.c
> +@@ -138,3 +138,24 @@ int board_eth_init(bd_t *bis)
> + return dm9000_initialize(bis);
> + }
> + #endif
> ++
> ++/*
> ++ * Routine: get_board_mem_timings
> ++ * Description: If we use SPL then there is no x-loader nor config header
> ++ * so we have to setup the DDR timings ourself on the first bank. This
> ++ * provides the timing values back to the function that configures
> ++ * the memory. We have either one or two banks of 128MB DDR.
> ++ */
> ++void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
> ++ u32 *mr)
> ++{
> ++ /* General SDRC config */
> ++ *mcfg = MICRON_V_MCFG_165(128 << 20);
> ++ *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
> ++
> ++ /* AC timings */
> ++ *ctrla = MICRON_V_ACTIMA_165;
> ++ *ctrlb = MICRON_V_ACTIMB_165;
> ++
> ++ *mr = MICRON_V_MR_165;
> ++}
> +diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h
> +index e1743dc..b3e60cd 100644
> +--- a/include/configs/devkit8000.h
> ++++ b/include/configs/devkit8000.h
> +@@ -68,10 +68,6 @@
> + #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
> +
> + /* Hardware drivers */
> +-
> +-/* DDR - I use Micron DDR */
> +-#define CONFIG_OMAP3_MICRON_DDR 1
> +-
> + /* DM9000 */
> + #define CONFIG_NET_RETRY_COUNT 20
> + #define CONFIG_DRIVER_DM9000 1
> +@@ -284,7 +280,6 @@
> + /* Physical Memory Map */
> + #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
> + #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
> +-#define PHYS_SDRAM_1_SIZE (128 << 20) /* at least 128 MiB */
> + #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
> +
> + /* SDRAM Bank Allocation method */
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0010-OMAP3-SPL-Add-identify_nand_chip-function.patch b/recipes-bsp/u-boot/u-boot/2011.09/0010-OMAP3-SPL-Add-identify_nand_chip-function.patch
> new file mode 100644
> index 0000000..94ef0de
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0010-OMAP3-SPL-Add-identify_nand_chip-function.patch
> @@ -0,0 +1,142 @@
> +From 290ebce5d39112ce80c6180206952aa5cc0ea871 Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:48:07 +0000
> +Subject: [PATCH 10/21] OMAP3 SPL: Add identify_nand_chip function
> +
> +A number of boards are populated with a PoP chip for both DDR and NAND
> +memory. Other boards may simply use this as an easy way to identify
> +board revs. So we provide a function that can be called early to reset
> +the NAND chip and return the result of NAND_CMD_READID. All of this
> +code is put into spl_id_nand.c and controlled via CONFIG_SPL_OMAP3_ID_NAND.
> +
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + arch/arm/cpu/armv7/omap3/Makefile | 3 +
> + arch/arm/cpu/armv7/omap3/spl_id_nand.c | 87 +++++++++++++++++++++++++++
> + arch/arm/include/asm/arch-omap3/sys_proto.h | 1 +
> + 3 files changed, 91 insertions(+), 0 deletions(-)
> + create mode 100644 arch/arm/cpu/armv7/omap3/spl_id_nand.c
> +
> +diff --git a/arch/arm/cpu/armv7/omap3/Makefile b/arch/arm/cpu/armv7/omap3/Makefile
> +index 8e85891..4b38e45 100644
> +--- a/arch/arm/cpu/armv7/omap3/Makefile
> ++++ b/arch/arm/cpu/armv7/omap3/Makefile
> +@@ -31,6 +31,9 @@ COBJS += board.o
> + COBJS += clock.o
> + COBJS += mem.o
> + COBJS += sys_info.o
> ++ifdef CONFIG_SPL_BUILD
> ++COBJS-$(CONFIG_SPL_OMAP3_ID_NAND) += spl_id_nand.o
> ++endif
> +
> + COBJS-$(CONFIG_EMIF4) += emif4.o
> + COBJS-$(CONFIG_SDRC) += sdrc.o
> +diff --git a/arch/arm/cpu/armv7/omap3/spl_id_nand.c b/arch/arm/cpu/armv7/omap3/spl_id_nand.c
> +new file mode 100644
> +index 0000000..0871fc9
> +--- /dev/null
> ++++ b/arch/arm/cpu/armv7/omap3/spl_id_nand.c
> +@@ -0,0 +1,87 @@
> ++/*
> ++ * (C) Copyright 2011
> ++ * Texas Instruments, <www.ti.com>
> ++ *
> ++ * Author :
> ++ * Tom Rini <trini at ti.com>
> ++ *
> ++ * Initial Code from:
> ++ * Richard Woodruff <r-woodruff2 at ti.com>
> ++ * Jian Zhang <jzhang at ti.com>
> ++ *
> ++ * This program is free software; you can redistribute it and/or
> ++ * modify it under the terms of the GNU General Public License as
> ++ * published by the Free Software Foundation; either version 2 of
> ++ * the License, or (at your option) any later version.
> ++ *
> ++ * This program is distributed in the hope that it will be useful,
> ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
> ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> ++ * GNU General Public License for more details.
> ++ *
> ++ * You should have received a copy of the GNU General Public License
> ++ * along with this program; if not, write to the Free Software
> ++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> ++ * MA 02111-1307 USA
> ++ */
> ++
> ++#include <common.h>
> ++#include <linux/mtd/nand.h>
> ++#include <asm/io.h>
> ++#include <asm/arch/sys_proto.h>
> ++#include <asm/arch/mem.h>
> ++
> ++static struct gpmc *gpmc_config = (struct gpmc *)GPMC_BASE;
> ++
> ++/* nand_command: Send a flash command to the flash chip */
> ++static void nand_command(u8 command)
> ++{
> ++ writeb(command, &gpmc_config->cs[0].nand_cmd);
> ++
> ++ if (command == NAND_CMD_RESET) {
> ++ unsigned char ret_val;
> ++ writeb(NAND_CMD_STATUS, &gpmc_config->cs[0].nand_cmd);
> ++ do {
> ++ /* Wait until ready */
> ++ ret_val = readl(&gpmc_config->cs[0].nand_dat);
> ++ } while ((ret_val & NAND_STATUS_READY) != NAND_STATUS_READY);
> ++ }
> ++}
> ++
> ++/*
> ++ * Many boards will want to know the results of the NAND_CMD_READID command
> ++ * in order to decide what to do about DDR initialization. This function
> ++ * allows us to do that very early and to pass those results back to the
> ++ * board so it can make whatever decisions need to be made.
> ++ */
> ++void identify_nand_chip(int *mfr, int *id)
> ++{
> ++ /* Make sure that we have setup GPMC for NAND correctly. */
> ++ writel(M_NAND_GPMC_CONFIG1, &gpmc_config->cs[0].config1);
> ++ writel(M_NAND_GPMC_CONFIG2, &gpmc_config->cs[0].config2);
> ++ writel(M_NAND_GPMC_CONFIG3, &gpmc_config->cs[0].config3);
> ++ writel(M_NAND_GPMC_CONFIG4, &gpmc_config->cs[0].config4);
> ++ writel(M_NAND_GPMC_CONFIG5, &gpmc_config->cs[0].config5);
> ++ writel(M_NAND_GPMC_CONFIG6, &gpmc_config->cs[0].config6);
> ++
> ++ /*
> ++ * Enable the config. The CS size goes in bits 11:8. We set
> ++ * bit 6 to enable the CS and the base address goes into bits 5:0.
> ++ */
> ++ writel((GPMC_SIZE_128M << 8) | (GPMC_CS_ENABLE << 6) |
> ++ ((NAND_BASE >> 24) & GPMC_BASEADDR_MASK),
> ++ &gpmc_config->cs[0].config7);
> ++
> ++ sdelay(2000);
> ++
> ++ /* Issue a RESET and then READID */
> ++ nand_command(NAND_CMD_RESET);
> ++ nand_command(NAND_CMD_READID);
> ++
> ++ /* Set the address to read to 0x0 */
> ++ writeb(0x0, &gpmc_config->cs[0].nand_adr);
> ++
> ++ /* Read off the manufacturer and device id. */
> ++ *mfr = readb(&gpmc_config->cs[0].nand_dat);
> ++ *id = readb(&gpmc_config->cs[0].nand_dat);
> ++}
> +diff --git a/arch/arm/include/asm/arch-omap3/sys_proto.h b/arch/arm/include/asm/arch-omap3/sys_proto.h
> +index 80e167b..e5031d5 100644
> +--- a/arch/arm/include/asm/arch-omap3/sys_proto.h
> ++++ b/arch/arm/include/asm/arch-omap3/sys_proto.h
> +@@ -40,6 +40,7 @@ void sdrc_init(void);
> + void do_sdrc_init(u32, u32);
> + void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
> + u32 *mr);
> ++void identify_nand_chip(int *mfr, int *id);
> + void emif4_init(void);
> + void gpmc_init(void);
> + void enable_gpmc_cs_config(const u32 *gpmc_config, struct gpmc_cs *cs, u32 base,
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0011-OMAP3-Add-SPL-support-to-Beagleboard.patch b/recipes-bsp/u-boot/u-boot/2011.09/0011-OMAP3-Add-SPL-support-to-Beagleboard.patch
> new file mode 100644
> index 0000000..a32c21d
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0011-OMAP3-Add-SPL-support-to-Beagleboard.patch
> @@ -0,0 +1,315 @@
> +From 4ce72b52b5eeb172c1118fbd6e23d49eeec30ad2 Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:48:08 +0000
> +Subject: [PATCH 11/21] OMAP3: Add SPL support to Beagleboard
> +
> +This introduces 200MHz Micron parts timing information based on x-loader
> +to <asm/arch-omap3/mem.h> and Numonyx MCFG calculation. The memory init
> +logic is also based on what x-loader does in these cases. Note that
> +while previously u-boot would be flashed in with SW ECC in this case it
> +now must be flashed with HW ECC. We also change CONFIG_SYS_TEXT_BASE to
> +0x80100000.
> +
> +Cc: Dirk Behme <dirk.behme at gmail.com>
> +Beagleboard rev C5, xM rev A:
> +Tested-by: Tom Rini <trini at ti.com>
> +Beagleboard xM rev C:
> +Tested-by: Matt Ranostay <mranostay at gmail.com>
> +Beagleboard rev B7, C2, xM rev B:
> +Tested-by: Matt Porter <mporter at ti.com>
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + arch/arm/include/asm/arch-omap3/mem.h | 29 +++++++++++++
> + board/ti/beagle/beagle.c | 71 ++++++++++++++++++++++++++++++++-
> + board/ti/beagle/config.mk | 33 ---------------
> + include/configs/omap3_beagle.h | 59 +++++++++++++++++++++++++--
> + 4 files changed, 153 insertions(+), 39 deletions(-)
> + delete mode 100644 board/ti/beagle/config.mk
> +
> +diff --git a/arch/arm/include/asm/arch-omap3/mem.h b/arch/arm/include/asm/arch-omap3/mem.h
> +index 09f5872..4ea5f74 100644
> +--- a/arch/arm/include/asm/arch-omap3/mem.h
> ++++ b/arch/arm/include/asm/arch-omap3/mem.h
> +@@ -186,6 +186,32 @@ enum {
> + (MICRON_CASL_165 << 4) | (MICRON_SIL_165 << 3) | \
> + (MICRON_BL_165))
> +
> ++/* Micron part (200MHz optimized) 5 ns */
> ++#define MICRON_TDAL_200 6
> ++#define MICRON_TDPL_200 3
> ++#define MICRON_TRRD_200 2
> ++#define MICRON_TRCD_200 3
> ++#define MICRON_TRP_200 3
> ++#define MICRON_TRAS_200 8
> ++#define MICRON_TRC_200 11
> ++#define MICRON_TRFC_200 15
> ++#define MICRON_V_ACTIMA_200 \
> ++ ACTIM_CTRLA(MICRON_TRFC_200, MICRON_TRC_200, \
> ++ MICRON_TRAS_200, MICRON_TRP_200, \
> ++ MICRON_TRCD_200, MICRON_TRRD_200, \
> ++ MICRON_TDPL_200, MICRON_TDAL_200)
> ++
> ++#define MICRON_TWTR_200 2
> ++#define MICRON_TCKE_200 4
> ++#define MICRON_TXP_200 2
> ++#define MICRON_XSR_200 23
> ++#define MICRON_V_ACTIMB_200 \
> ++ ACTIM_CTRLB(MICRON_TWTR_200, MICRON_TCKE_200, \
> ++ MICRON_TXP_200, MICRON_XSR_200)
> ++
> ++#define MICRON_RASWIDTH_200 0x3
> ++#define MICRON_V_MCFG_200(size) MCFG((size), MICRON_RASWIDTH_200)
> ++
> + /* NUMONYX part of IGEP v2 (165MHz optimized) 6.06ns */
> + #define NUMONYX_TDAL_165 6 /* Twr/Tck + Trp/tck */
> + /* 15/6 + 18/6 = 5.5 -> 6 */
> +@@ -212,6 +238,9 @@ enum {
> + ACTIM_CTRLB(NUMONYX_TWTR_165, NUMONYX_TCKE_165, \
> + NUMONYX_TXP_165, NUMONYX_XSR_165)
> +
> ++#define NUMONYX_RASWIDTH_165 0x4
> ++#define NUMONYX_V_MCFG_165(size) MCFG((size), NUMONYX_RASWIDTH_165)
> ++
> + /*
> + * GPMC settings -
> + * Definitions is as per the following format
> +diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c
> +index 9482c5e..6a457cb 100644
> +--- a/board/ti/beagle/beagle.c
> ++++ b/board/ti/beagle/beagle.c
> +@@ -1,5 +1,5 @@
> + /*
> +- * (C) Copyright 2004-2008
> ++ * (C) Copyright 2004-2011
> + * Texas Instruments, <www.ti.com>
> + *
> + * Author :
> +@@ -34,9 +34,11 @@
> + #include <status_led.h>
> + #endif
> + #include <twl4030.h>
> ++#include <linux/mtd/nand.h>
> + #include <asm/io.h>
> + #include <asm/arch/mmc_host_def.h>
> + #include <asm/arch/mux.h>
> ++#include <asm/arch/mem.h>
> + #include <asm/arch/sys_proto.h>
> + #include <asm/gpio.h>
> + #include <asm/mach-types.h>
> +@@ -135,6 +137,69 @@ int get_board_revision(void)
> + return revision;
> + }
> +
> ++#ifdef CONFIG_SPL_BUILD
> ++/*
> ++ * Routine: get_board_mem_timings
> ++ * Description: If we use SPL then there is no x-loader nor config header
> ++ * so we have to setup the DDR timings ourself on both banks.
> ++ */
> ++void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
> ++ u32 *mr)
> ++{
> ++ int pop_mfr, pop_id;
> ++
> ++ /*
> ++ * We need to identify what PoP memory is on the board so that
> ++ * we know what timings to use. If we can't identify it then
> ++ * we know it's an xM. To map the ID values please see nand_ids.c
> ++ */
> ++ identify_nand_chip(&pop_mfr, &pop_id);
> ++
> ++ *mr = MICRON_V_MR_165;
> ++ switch (get_board_revision()) {
> ++ case REVISION_C4:
> ++ if (pop_mfr == NAND_MFR_STMICRO && pop_id == 0xba) {
> ++ /* 512MB DDR */
> ++ *mcfg = NUMONYX_V_MCFG_165(512 << 20);
> ++ *ctrla = NUMONYX_V_ACTIMA_165;
> ++ *ctrlb = NUMONYX_V_ACTIMB_165;
> ++ *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
> ++ break;
> ++ } else if (pop_mfr == NAND_MFR_MICRON && pop_id == 0xbc) {
> ++ /* Beagleboard Rev C5, 256MB DDR */
> ++ *mcfg = MICRON_V_MCFG_200(256 << 20);
> ++ *ctrla = MICRON_V_ACTIMA_200;
> ++ *ctrlb = MICRON_V_ACTIMB_200;
> ++ *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
> ++ break;
> ++ }
> ++ case REVISION_XM_A:
> ++ case REVISION_XM_B:
> ++ case REVISION_XM_C:
> ++ if (pop_mfr == 0) {
> ++ /* 256MB DDR */
> ++ *mcfg = MICRON_V_MCFG_200(256 << 20);
> ++ *ctrla = MICRON_V_ACTIMA_200;
> ++ *ctrlb = MICRON_V_ACTIMB_200;
> ++ *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
> ++ } else {
> ++ /* 512MB DDR */
> ++ *mcfg = NUMONYX_V_MCFG_165(512 << 20);
> ++ *ctrla = NUMONYX_V_ACTIMA_165;
> ++ *ctrlb = NUMONYX_V_ACTIMB_165;
> ++ *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
> ++ }
> ++ break;
> ++ default:
> ++ /* Assume 128MB and Micron/165MHz timings to be safe */
> ++ *mcfg = MICRON_V_MCFG_165(128 << 20);
> ++ *ctrla = MICRON_V_ACTIMA_165;
> ++ *ctrlb = MICRON_V_ACTIMB_165;
> ++ *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
> ++ }
> ++}
> ++#endif
> ++
> + /*
> + * Routine: get_expansion_id
> + * Description: This function checks for expansion board by checking I2C
> +@@ -367,7 +432,7 @@ void set_muxconf_regs(void)
> + MUX_BEAGLE();
> + }
> +
> +-#ifdef CONFIG_GENERIC_MMC
> ++#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
> + int board_mmc_init(bd_t *bis)
> + {
> + omap_mmc_init(0);
> +@@ -476,6 +541,7 @@ int ehci_hcd_init(void)
> +
> + #endif /* CONFIG_USB_EHCI */
> +
> ++#ifndef CONFIG_SPL_BUILD
> + /*
> + * This command returns the status of the user button on beagle xM
> + * Input - none
> +@@ -528,3 +594,4 @@ U_BOOT_CMD(
> + "Return the status of the BeagleBoard USER button",
> + ""
> + );
> ++#endif
> +diff --git a/board/ti/beagle/config.mk b/board/ti/beagle/config.mk
> +deleted file mode 100644
> +index cf055db..0000000
> +--- a/board/ti/beagle/config.mk
> ++++ /dev/null
> +@@ -1,33 +0,0 @@
> +-#
> +-# (C) Copyright 2006
> +-# Texas Instruments, <www.ti.com>
> +-#
> +-# Beagle Board uses OMAP3 (ARM-CortexA8) cpu
> +-# see http://www.ti.com/ for more information on Texas Instruments
> +-#
> +-# See file CREDITS for list of people who contributed to this
> +-# project.
> +-#
> +-# This program is free software; you can redistribute it and/or
> +-# modify it under the terms of the GNU General Public License as
> +-# published by the Free Software Foundation; either version 2 of
> +-# the License, or (at your option) any later version.
> +-#
> +-# This program is distributed in the hope that it will be useful,
> +-# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +-# GNU General Public License for more details.
> +-#
> +-# You should have received a copy of the GNU General Public License
> +-# along with this program; if not, write to the Free Software
> +-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> +-# MA 02111-1307 USA
> +-#
> +-# Physical Address:
> +-# 8000'0000 (bank0)
> +-# A000/0000 (bank1)
> +-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
> +-# (mem base + reserved)
> +-
> +-# For use with external or internal boots.
> +-CONFIG_SYS_TEXT_BASE = 0x80008000
> +diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
> +index 15e40c5..941ec38 100644
> +--- a/include/configs/omap3_beagle.h
> ++++ b/include/configs/omap3_beagle.h
> +@@ -111,9 +111,6 @@
> + #define STATUS_LED_BOOT STATUS_LED_BIT
> + #define STATUS_LED_GREEN STATUS_LED_BIT1
> +
> +-/* DDR - I use Micron DDR */
> +-#define CONFIG_OMAP3_MICRON_DDR 1
> +-
> + /* Enable Multi Bus support for I2C */
> + #define CONFIG_I2C_MULTI_BUS 1
> +
> +@@ -347,7 +344,6 @@
> + */
> + #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
> + #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
> +-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
> + #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
> +
> + /* SDRAM Bank Allocation method */
> +@@ -390,4 +386,59 @@
> +
> + #define CONFIG_OMAP3_SPI
> +
> ++/* Defines for SPL */
> ++#define CONFIG_SPL
> ++#define CONFIG_SPL_NAND_SIMPLE
> ++#define CONFIG_SPL_TEXT_BASE 0x40200800
> ++#define CONFIG_SPL_MAX_SIZE (45 * 1024)
> ++#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
> ++
> ++#define CONFIG_SPL_BSS_START_ADDR 0x80000000
> ++#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
> ++
> ++#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
> ++#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
> ++#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
> ++#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
> ++
> ++#define CONFIG_SPL_LIBCOMMON_SUPPORT
> ++#define CONFIG_SPL_LIBDISK_SUPPORT
> ++#define CONFIG_SPL_I2C_SUPPORT
> ++#define CONFIG_SPL_LIBGENERIC_SUPPORT
> ++#define CONFIG_SPL_MMC_SUPPORT
> ++#define CONFIG_SPL_FAT_SUPPORT
> ++#define CONFIG_SPL_SERIAL_SUPPORT
> ++#define CONFIG_SPL_NAND_SUPPORT
> ++#define CONFIG_SPL_POWER_SUPPORT
> ++#define CONFIG_SPL_OMAP3_ID_NAND
> ++#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
> ++
> ++/* NAND boot config */
> ++#define CONFIG_SYS_NAND_5_ADDR_CYCLE
> ++#define CONFIG_SYS_NAND_PAGE_COUNT 64
> ++#define CONFIG_SYS_NAND_PAGE_SIZE 2048
> ++#define CONFIG_SYS_NAND_OOBSIZE 64
> ++#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
> ++#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
> ++#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
> ++ 10, 11, 12, 13}
> ++#define CONFIG_SYS_NAND_ECCSIZE 512
> ++#define CONFIG_SYS_NAND_ECCBYTES 3
> ++#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \
> ++ CONFIG_SYS_NAND_ECCSIZE)
> ++#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \
> ++ CONFIG_SYS_NAND_ECCSTEPS)
> ++#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
> ++#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
> ++
> ++/*
> ++ * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
> ++ * 64 bytes before this address should be set aside for u-boot.img's
> ++ * header. That is 0x800FFFC0--0x80100000 should not be used for any
> ++ * other needs.
> ++ */
> ++#define CONFIG_SYS_TEXT_BASE 0x80100000
> ++#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
> ++#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
> ++
> + #endif /* __CONFIG_H */
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0012-OMAP3-Add-SPL-support-to-omap3_evm.patch b/recipes-bsp/u-boot/u-boot/2011.09/0012-OMAP3-Add-SPL-support-to-omap3_evm.patch
> new file mode 100644
> index 0000000..7121ff7
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0012-OMAP3-Add-SPL-support-to-omap3_evm.patch
> @@ -0,0 +1,319 @@
> +From a2985d6ef29ee6eb09ad1b40cf09f955549e66e2 Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:48:09 +0000
> +Subject: [PATCH 12/21] OMAP3: Add SPL support to omap3_evm
> +
> +Add Hynix 200MHz timing information to <asm/arch-omap3/mem.h>.
> +This also changes CONFIG_SYS_TEXT_BASE to 0x80100000.
> +
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + arch/arm/include/asm/arch-omap3/mem.h | 26 ++++++++++++++++++++
> + board/ti/evm/config.mk | 33 -------------------------
> + board/ti/evm/evm.c | 41 ++++++++++++++++++++++++++++++-
> + include/configs/omap3_evm.h | 27 +++++++++++++++++++++
> + include/configs/omap3_evm_common.h | 30 +++++++++++++++++++++-
> + include/configs/omap3_evm_quick_mmc.h | 10 +++++++
> + include/configs/omap3_evm_quick_nand.h | 22 +++++++++++++++++
> + 7 files changed, 152 insertions(+), 37 deletions(-)
> + delete mode 100644 board/ti/evm/config.mk
> +
> +diff --git a/arch/arm/include/asm/arch-omap3/mem.h b/arch/arm/include/asm/arch-omap3/mem.h
> +index 4ea5f74..5fd02d4 100644
> +--- a/arch/arm/include/asm/arch-omap3/mem.h
> ++++ b/arch/arm/include/asm/arch-omap3/mem.h
> +@@ -123,6 +123,32 @@ enum {
> + V_MCFG_BANKALLOCATION_RBC | \
> + V_MCFG_B32NOT16_32 | V_MCFG_DEEPPD_EN | V_MCFG_RAMTYPE_DDR
> +
> ++/* Hynix part of AM/DM37xEVM (200MHz optimized) */
> ++#define HYNIX_TDAL_200 6
> ++#define HYNIX_TDPL_200 3
> ++#define HYNIX_TRRD_200 2
> ++#define HYNIX_TRCD_200 4
> ++#define HYNIX_TRP_200 3
> ++#define HYNIX_TRAS_200 8
> ++#define HYNIX_TRC_200 11
> ++#define HYNIX_TRFC_200 18
> ++#define HYNIX_V_ACTIMA_200 \
> ++ ACTIM_CTRLA(HYNIX_TRFC_200, HYNIX_TRC_200, \
> ++ HYNIX_TRAS_200, HYNIX_TRP_200, \
> ++ HYNIX_TRCD_200, HYNIX_TRRD_200, \
> ++ HYNIX_TDPL_200, HYNIX_TDAL_200)
> ++
> ++#define HYNIX_TWTR_200 2
> ++#define HYNIX_TCKE_200 1
> ++#define HYNIX_TXP_200 1
> ++#define HYNIX_XSR_200 28
> ++#define HYNIX_V_ACTIMB_200 \
> ++ ACTIM_CTRLB(HYNIX_TWTR_200, HYNIX_TCKE_200, \
> ++ HYNIX_TXP_200, HYNIX_XSR_200)
> ++
> ++#define HYNIX_RASWIDTH_200 0x3
> ++#define HYNIX_V_MCFG_200(size) MCFG((size), HYNIX_RASWIDTH_200)
> ++
> + /* Infineon part of 3430SDP (165MHz optimized) 6.06ns */
> + #define INFINEON_TDAL_165 6 /* Twr/Tck + Trp/tck */
> + /* 15/6 + 18/6 = 5.5 -> 6 */
> +diff --git a/board/ti/evm/config.mk b/board/ti/evm/config.mk
> +deleted file mode 100644
> +index d173eef..0000000
> +--- a/board/ti/evm/config.mk
> ++++ /dev/null
> +@@ -1,33 +0,0 @@
> +-#
> +-# (C) Copyright 2006 - 2008
> +-# Texas Instruments, <www.ti.com>
> +-#
> +-# EVM uses OMAP3 (ARM-CortexA8) cpu
> +-# see http://www.ti.com/ for more information on Texas Instruments
> +-#
> +-# See file CREDITS for list of people who contributed to this
> +-# project.
> +-#
> +-# This program is free software; you can redistribute it and/or
> +-# modify it under the terms of the GNU General Public License as
> +-# published by the Free Software Foundation; either version 2 of
> +-# the License, or (at your option) any later version.
> +-#
> +-# This program is distributed in the hope that it will be useful,
> +-# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +-# GNU General Public License for more details.
> +-#
> +-# You should have received a copy of the GNU General Public License
> +-# along with this program; if not, write to the Free Software
> +-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> +-# MA 02111-1307 USA
> +-#
> +-# Physical Address:
> +-# 8000'0000 (bank0)
> +-# A000/0000 (bank1)
> +-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
> +-# (mem base + reserved)
> +-
> +-# For use with external or internal boots.
> +-CONFIG_SYS_TEXT_BASE = 0x80008000
> +diff --git a/board/ti/evm/evm.c b/board/ti/evm/evm.c
> +index 8c43463..8497aee 100644
> +--- a/board/ti/evm/evm.c
> ++++ b/board/ti/evm/evm.c
> +@@ -1,5 +1,5 @@
> + /*
> +- * (C) Copyright 2004-2008
> ++ * (C) Copyright 2004-2011
> + * Texas Instruments, <www.ti.com>
> + *
> + * Author :
> +@@ -37,6 +37,7 @@
> + #include <asm/gpio.h>
> + #include <i2c.h>
> + #include <asm/mach-types.h>
> ++#include <linux/mtd/nand.h>
> + #include "evm.h"
> +
> + #define OMAP3EVM_GPIO_ETH_RST_GEN1 64
> +@@ -119,6 +120,42 @@ int board_init(void)
> + return 0;
> + }
> +
> ++#ifdef CONFIG_SPL_BUILD
> ++/*
> ++ * Routine: get_board_mem_timings
> ++ * Description: If we use SPL then there is no x-loader nor config header
> ++ * so we have to setup the DDR timings ourself on the first bank. This
> ++ * provides the timing values back to the function that configures
> ++ * the memory.
> ++ */
> ++void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
> ++ u32 *mr)
> ++{
> ++ int pop_mfr, pop_id;
> ++
> ++ /*
> ++ * We need to identify what PoP memory is on the board so that
> ++ * we know what timings to use. To map the ID values please see
> ++ * nand_ids.c
> ++ */
> ++ identify_nand_chip(&pop_mfr, &pop_id);
> ++
> ++ if (pop_mfr == NAND_MFR_HYNIX && pop_id == 0xbc) {
> ++ /* 256MB DDR */
> ++ *mcfg = HYNIX_V_MCFG_200(256 << 20);
> ++ *ctrla = HYNIX_V_ACTIMA_200;
> ++ *ctrlb = HYNIX_V_ACTIMB_200;
> ++ } else {
> ++ /* 128MB DDR */
> ++ *mcfg = MICRON_V_MCFG_165(128 << 20);
> ++ *ctrla = MICRON_V_ACTIMA_165;
> ++ *ctrlb = MICRON_V_ACTIMB_165;
> ++ }
> ++ *rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
> ++ *mr = MICRON_V_MR_165;
> ++}
> ++#endif
> ++
> + /*
> + * Routine: misc_init_r
> + * Description: Init ethernet (done here so udelay works)
> +@@ -238,7 +275,7 @@ int board_eth_init(bd_t *bis)
> + }
> + #endif /* CONFIG_CMD_NET */
> +
> +-#ifdef CONFIG_GENERIC_MMC
> ++#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
> + int board_mmc_init(bd_t *bis)
> + {
> + omap_mmc_init(0);
> +diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h
> +index 47ec39f..dc611ca 100644
> +--- a/include/configs/omap3_evm.h
> ++++ b/include/configs/omap3_evm.h
> +@@ -84,6 +84,13 @@
> + #define CONFIG_GENERIC_MMC
> + #define CONFIG_OMAP_HSMMC
> + #define CONFIG_DOS_PARTITION
> ++/* SPL */
> ++#define CONFIG_SPL_MMC_SUPPORT
> ++#define CONFIG_SPL_FAT_SUPPORT
> ++#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
> ++#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
> ++#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
> ++#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
> +
> + /* USB
> + *
> +@@ -94,6 +101,26 @@
> + #define CONFIG_MUSB_HCD
> + /* #define CONFIG_MUSB_UDC */
> +
> ++/* NAND SPL */
> ++#define CONFIG_SPL_NAND_SIMPLE
> ++#define CONFIG_SPL_NAND_SUPPORT
> ++#define CONFIG_SYS_NAND_5_ADDR_CYCLE
> ++#define CONFIG_SYS_NAND_PAGE_COUNT 64
> ++#define CONFIG_SYS_NAND_PAGE_SIZE 2048
> ++#define CONFIG_SYS_NAND_OOBSIZE 64
> ++#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
> ++#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
> ++#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
> ++ 10, 11, 12, 13}
> ++#define CONFIG_SYS_NAND_ECCSIZE 512
> ++#define CONFIG_SYS_NAND_ECCBYTES 3
> ++#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \
> ++ CONFIG_SYS_NAND_ECCSIZE)
> ++#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \
> ++ CONFIG_SYS_NAND_ECCSTEPS)
> ++#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
> ++#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
> ++
> + /* -----------------------------------------------------------------------------
> + * Include common board configuration
> + * -----------------------------------------------------------------------------
> +diff --git a/include/configs/omap3_evm_common.h b/include/configs/omap3_evm_common.h
> +index 54aa7a7..a2aeb76 100644
> +--- a/include/configs/omap3_evm_common.h
> ++++ b/include/configs/omap3_evm_common.h
> +@@ -27,7 +27,6 @@
> + #define CONFIG_SDRC /* The chip has SDRC controller */
> +
> + #define CONFIG_OMAP3_EVM /* This is a OMAP3 EVM */
> +-#define CONFIG_OMAP3_MICRON_DDR /* with MICRON DDR part */
> + #define CONFIG_TWL4030_POWER /* with TWL4030 PMIC */
> +
> + #undef CONFIG_USE_IRQ /* no support for IRQs */
> +@@ -71,7 +70,6 @@
> + */
> + #define CONFIG_NR_DRAM_BANKS 2
> + #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
> +-#define PHYS_SDRAM_1_SIZE (32 << 20)
> + #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
> +
> + /* SDRAM Bank Allocation method */
> +@@ -289,4 +287,32 @@
> + /* Uncomment to define the board revision statically */
> + /* #define CONFIG_STATIC_BOARD_REV OMAP3EVM_BOARD_GEN_2 */
> +
> ++/* Defines for SPL */
> ++#define CONFIG_SPL
> ++#define CONFIG_SPL_TEXT_BASE 0x40200800
> ++#define CONFIG_SPL_MAX_SIZE (45 * 1024) /* 45 KB */
> ++#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
> ++
> ++#define CONFIG_SPL_BSS_START_ADDR 0x80000000
> ++#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
> ++
> ++#define CONFIG_SPL_LIBCOMMON_SUPPORT
> ++#define CONFIG_SPL_LIBDISK_SUPPORT
> ++#define CONFIG_SPL_I2C_SUPPORT
> ++#define CONFIG_SPL_LIBGENERIC_SUPPORT
> ++#define CONFIG_SPL_SERIAL_SUPPORT
> ++#define CONFIG_SPL_POWER_SUPPORT
> ++#define CONFIG_SPL_OMAP3_ID_NAND
> ++#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
> ++
> ++/*
> ++ * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
> ++ * 64 bytes before this address should be set aside for u-boot.img's
> ++ * header. That is 0x800FFFC0--0x80100000 should not be used for any
> ++ * other needs.
> ++ */
> ++#define CONFIG_SYS_TEXT_BASE 0x80100000
> ++#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
> ++#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
> ++
> + #endif /* __OMAP3_EVM_COMMON_H */
> +diff --git a/include/configs/omap3_evm_quick_mmc.h b/include/configs/omap3_evm_quick_mmc.h
> +index 691e4c2..912da7d 100644
> +--- a/include/configs/omap3_evm_quick_mmc.h
> ++++ b/include/configs/omap3_evm_quick_mmc.h
> +@@ -88,4 +88,14 @@
> + "root=/dev/mmcblk0p2 rw " \
> + "rootfstype=ext3 rootwait"
> +
> ++/*
> ++ * SPL
> ++ */
> ++#define CONFIG_SPL_MMC_SUPPORT
> ++#define CONFIG_SPL_FAT_SUPPORT
> ++#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
> ++#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
> ++#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
> ++#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
> ++
> + #endif /* __OMAP3_EVM_QUICK_MMC_H */
> +diff --git a/include/configs/omap3_evm_quick_nand.h b/include/configs/omap3_evm_quick_nand.h
> +index 2d18314..2f879c0 100644
> +--- a/include/configs/omap3_evm_quick_nand.h
> ++++ b/include/configs/omap3_evm_quick_nand.h
> +@@ -76,4 +76,26 @@
> + "root=/dev/mtdblock4 rw " \
> + "rootfstype=jffs2 "
> +
> ++/*
> ++ * SPL
> ++ */
> ++#define CONFIG_SPL_NAND_SIMPLE
> ++#define CONFIG_SPL_NAND_SUPPORT
> ++#define CONFIG_SYS_NAND_5_ADDR_CYCLE
> ++#define CONFIG_SYS_NAND_PAGE_COUNT 64
> ++#define CONFIG_SYS_NAND_PAGE_SIZE 2048
> ++#define CONFIG_SYS_NAND_OOBSIZE 64
> ++#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
> ++#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
> ++#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
> ++ 10, 11, 12, 13}
> ++#define CONFIG_SYS_NAND_ECCSIZE 512
> ++#define CONFIG_SYS_NAND_ECCBYTES 3
> ++#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \
> ++ CONFIG_SYS_NAND_ECCSIZE)
> ++#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \
> ++ CONFIG_SYS_NAND_ECCSTEPS)
> ++#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
> ++#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
> ++
> + #endif /* __OMAP3_EVM_QUICK_NAND_H */
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0013-AM3517-Add-SPL-support.patch b/recipes-bsp/u-boot/u-boot/2011.09/0013-AM3517-Add-SPL-support.patch
> new file mode 100644
> index 0000000..cb9c1b2
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0013-AM3517-Add-SPL-support.patch
> @@ -0,0 +1,150 @@
> +From aff5a412e0353407420ed63246ea630988ebf469 Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:48:10 +0000
> +Subject: [PATCH 13/21] AM3517: Add SPL support
> +
> +The only change of note is that we move from 0x80008000 to 0x80100000
> +for CONFIG_SYS_TEXT_BASE
> +
> +Cc: Vaibhav Hiremath <hvaibhav at ti.com>
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + board/logicpd/am3517evm/am3517evm.c | 2 +-
> + board/logicpd/am3517evm/config.mk | 30 ------------------
> + include/configs/am3517_evm.h | 57 +++++++++++++++++++++++++++++++++-
> + 3 files changed, 56 insertions(+), 33 deletions(-)
> + delete mode 100644 board/logicpd/am3517evm/config.mk
> +
> +diff --git a/board/logicpd/am3517evm/am3517evm.c b/board/logicpd/am3517evm/am3517evm.c
> +index c0a006a..0a105bf 100644
> +--- a/board/logicpd/am3517evm/am3517evm.c
> ++++ b/board/logicpd/am3517evm/am3517evm.c
> +@@ -76,7 +76,7 @@ void set_muxconf_regs(void)
> + MUX_AM3517EVM();
> + }
> +
> +-#ifdef CONFIG_GENERIC_MMC
> ++#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
> + int board_mmc_init(bd_t *bis)
> + {
> + omap_mmc_init(0);
> +diff --git a/board/logicpd/am3517evm/config.mk b/board/logicpd/am3517evm/config.mk
> +deleted file mode 100644
> +index 71ec5d0..0000000
> +--- a/board/logicpd/am3517evm/config.mk
> ++++ /dev/null
> +@@ -1,30 +0,0 @@
> +-#
> +-# Author: Vaibhav Hiremath <hvaibhav at ti.com>
> +-#
> +-# Based on ti/evm/config.mk
> +-#
> +-# Copyright (C) 2010
> +-# Texas Instruments Incorporated - http://www.ti.com/
> +-#
> +-# This program is free software; you can redistribute it and/or modify
> +-# it under the terms of the GNU General Public License as published by
> +-# the Free Software Foundation; either version 2 of the License, or
> +-# (at your option) any later version.
> +-#
> +-# This program is distributed in the hope that it will be useful,
> +-# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +-# GNU General Public License for more details.
> +-#
> +-# You should have received a copy of the GNU General Public License
> +-# along with this program; if not, write to the Free Software
> +-# Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
> +-#
> +-# Physical Address:
> +-# 8000'0000 (bank0)
> +-# A000/0000 (bank1)
> +-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
> +-# (mem base + reserved)
> +-
> +-# For use with external or internal boots.
> +-CONFIG_SYS_TEXT_BASE = 0x80008000
> +diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h
> +index 1c70b9d..4a1c72c 100644
> +--- a/include/configs/am3517_evm.h
> ++++ b/include/configs/am3517_evm.h
> +@@ -63,7 +63,6 @@
> + /*
> + * DDR related
> + */
> +-#define CONFIG_OMAP3_MICRON_DDR 1 /* Micron DDR */
> + #define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
> +
> + /*
> +@@ -273,7 +272,6 @@
> + */
> + #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
> + #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
> +-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
> + #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
> +
> + /* SDRAM Bank Allocation method */
> +@@ -331,4 +329,59 @@
> + #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
> + CONFIG_SYS_INIT_RAM_SIZE - \
> + GENERATED_GBL_DATA_SIZE)
> ++
> ++/* Defines for SPL */
> ++#define CONFIG_SPL
> ++#define CONFIG_SPL_NAND_SIMPLE
> ++#define CONFIG_SPL_TEXT_BASE 0x40200800
> ++#define CONFIG_SPL_MAX_SIZE (45 * 1024)
> ++#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
> ++
> ++#define CONFIG_SPL_BSS_START_ADDR 0x80000000
> ++#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
> ++
> ++#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
> ++#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
> ++#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
> ++#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
> ++
> ++#define CONFIG_SPL_LIBCOMMON_SUPPORT
> ++#define CONFIG_SPL_LIBDISK_SUPPORT
> ++#define CONFIG_SPL_I2C_SUPPORT
> ++#define CONFIG_SPL_LIBGENERIC_SUPPORT
> ++#define CONFIG_SPL_MMC_SUPPORT
> ++#define CONFIG_SPL_FAT_SUPPORT
> ++#define CONFIG_SPL_SERIAL_SUPPORT
> ++#define CONFIG_SPL_NAND_SUPPORT
> ++#define CONFIG_SPL_POWER_SUPPORT
> ++#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
> ++
> ++/* NAND boot config */
> ++#define CONFIG_SYS_NAND_5_ADDR_CYCLE
> ++#define CONFIG_SYS_NAND_PAGE_COUNT 64
> ++#define CONFIG_SYS_NAND_PAGE_SIZE 2048
> ++#define CONFIG_SYS_NAND_OOBSIZE 64
> ++#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
> ++#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
> ++#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
> ++ 10, 11, 12, 13}
> ++#define CONFIG_SYS_NAND_ECCSIZE 512
> ++#define CONFIG_SYS_NAND_ECCBYTES 3
> ++#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \
> ++ CONFIG_SYS_NAND_ECCSIZE)
> ++#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \
> ++ CONFIG_SYS_NAND_ECCSTEPS)
> ++#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
> ++#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
> ++
> ++/*
> ++ * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
> ++ * 64 bytes before this address should be set aside for u-boot.img's
> ++ * header. That is 0x800FFFC0--0x80100000 should not be used for any
> ++ * other needs.
> ++ */
> ++#define CONFIG_SYS_TEXT_BASE 0x80100000
> ++#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
> ++#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
> ++
> + #endif /* __CONFIG_H */
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0014-AM3517-CraneBoard-Add-SPL-support.patch b/recipes-bsp/u-boot/u-boot/2011.09/0014-AM3517-CraneBoard-Add-SPL-support.patch
> new file mode 100644
> index 0000000..22a3e71
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0014-AM3517-CraneBoard-Add-SPL-support.patch
> @@ -0,0 +1,150 @@
> +From 04567bb3a9e3b8aefe2a58c339c592c4b62b79d3 Mon Sep 17 00:00:00 2001
> +From: Tom Rini <trini at ti.com>
> +Date: Fri, 18 Nov 2011 12:48:11 +0000
> +Subject: [PATCH 14/21] AM3517 CraneBoard: Add SPL support
> +
> +The only change of note is that we move from 0x80008000 to 0x80100000
> +for CONFIG_SYS_TEXT_BASE
> +
> +Cc: Nagendra T S <nagendra at mistralsolutions.com>
> +Tested-by: Koen Kooi <k-kooi at ti.com>
> +Signed-off-by: Tom Rini <trini at ti.com>
> +Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> +---
> + board/ti/am3517crane/am3517crane.c | 2 +-
> + board/ti/am3517crane/config.mk | 29 ------------------
> + include/configs/am3517_crane.h | 57 ++++++++++++++++++++++++++++++++++-
> + 3 files changed, 56 insertions(+), 32 deletions(-)
> + delete mode 100644 board/ti/am3517crane/config.mk
> +
> +diff --git a/board/ti/am3517crane/am3517crane.c b/board/ti/am3517crane/am3517crane.c
> +index cd5683d..436645a 100644
> +--- a/board/ti/am3517crane/am3517crane.c
> ++++ b/board/ti/am3517crane/am3517crane.c
> +@@ -75,7 +75,7 @@ void set_muxconf_regs(void)
> + MUX_AM3517CRANE();
> + }
> +
> +-#ifdef CONFIG_GENERIC_MMC
> ++#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
> + int board_mmc_init(bd_t *bis)
> + {
> + omap_mmc_init(0);
> +diff --git a/board/ti/am3517crane/config.mk b/board/ti/am3517crane/config.mk
> +deleted file mode 100644
> +index c6a18b5..0000000
> +--- a/board/ti/am3517crane/config.mk
> ++++ /dev/null
> +@@ -1,29 +0,0 @@
> +-#
> +-# Author: Srinath R <srinath at mistralsolutions.com>
> +-#
> +-# Based on logicpd/am3517evm/config.mk
> +-#
> +-# Copyright (C) 2011 Mistral Solutions Pvt Ltd
> +-#
> +-# This program is free software; you can redistribute it and/or modify
> +-# it under the terms of the GNU General Public License as published by
> +-# the Free Software Foundation; either version 2 of the License, or
> +-# (at your option) any later version.
> +-#
> +-# This program is distributed in the hope that it will be useful,
> +-# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +-# GNU General Public License for more details.
> +-#
> +-# You should have received a copy of the GNU General Public License
> +-# along with this program; if not, write to the Free Software
> +-# Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
> +-#
> +-# Physical Address:
> +-# 8000'0000 (bank0)
> +-# A000/0000 (bank1)
> +-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
> +-# (mem base + reserved)
> +-
> +-# For use with external or internal boots.
> +-CONFIG_SYS_TEXT_BASE = 0x80008000
> +diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h
> +index 8842a18..68cbf37 100644
> +--- a/include/configs/am3517_crane.h
> ++++ b/include/configs/am3517_crane.h
> +@@ -64,7 +64,6 @@
> + /*
> + * DDR related
> + */
> +-#define CONFIG_OMAP3_MICRON_DDR 1 /* Micron DDR */
> + #define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
> +
> + /*
> +@@ -274,7 +273,6 @@
> + */
> + #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
> + #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
> +-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
> + #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
> +
> + /* SDRAM Bank Allocation method */
> +@@ -330,4 +328,59 @@
> + #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
> + CONFIG_SYS_INIT_RAM_SIZE - \
> + GENERATED_GBL_DATA_SIZE)
> ++
> ++/* Defines for SPL */
> ++#define CONFIG_SPL
> ++#define CONFIG_SPL_NAND_SIMPLE
> ++#define CONFIG_SPL_TEXT_BASE 0x40200800
> ++#define CONFIG_SPL_MAX_SIZE (45 * 1024)
> ++#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
> ++
> ++#define CONFIG_SPL_BSS_START_ADDR 0x80000000
> ++#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
> ++
> ++#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
> ++#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
> ++#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
> ++#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
> ++
> ++#define CONFIG_SPL_LIBCOMMON_SUPPORT
> ++#define CONFIG_SPL_LIBDISK_SUPPORT
> ++#define CONFIG_SPL_I2C_SUPPORT
> ++#define CONFIG_SPL_LIBGENERIC_SUPPORT
> ++#define CONFIG_SPL_MMC_SUPPORT
> ++#define CONFIG_SPL_FAT_SUPPORT
> ++#define CONFIG_SPL_SERIAL_SUPPORT
> ++#define CONFIG_SPL_NAND_SUPPORT
> ++#define CONFIG_SPL_POWER_SUPPORT
> ++#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
> ++
> ++/* NAND boot config */
> ++#define CONFIG_SYS_NAND_5_ADDR_CYCLE
> ++#define CONFIG_SYS_NAND_PAGE_COUNT 64
> ++#define CONFIG_SYS_NAND_PAGE_SIZE 2048
> ++#define CONFIG_SYS_NAND_OOBSIZE 64
> ++#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
> ++#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
> ++#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
> ++ 10, 11, 12, 13}
> ++#define CONFIG_SYS_NAND_ECCSIZE 512
> ++#define CONFIG_SYS_NAND_ECCBYTES 3
> ++#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \
> ++ CONFIG_SYS_NAND_ECCSIZE)
> ++#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \
> ++ CONFIG_SYS_NAND_ECCSTEPS)
> ++#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
> ++#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
> ++
> ++/*
> ++ * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
> ++ * 64 bytes before this address should be set aside for u-boot.img's
> ++ * header. That is 0x800FFFC0--0x80100000 should not be used for any
> ++ * other needs.
> ++ */
> ++#define CONFIG_SYS_TEXT_BASE 0x80100000
> ++#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
> ++#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
> ++
> + #endif /* __CONFIG_H */
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0001-HACK-beagleboard-config-disable-cache-for-USB.patch b/recipes-bsp/u-boot/u-boot/2011.09/0015-HACK-beagleboard-config-disable-cache-for-USB.patch
> similarity index 75%
> rename from recipes-bsp/u-boot/u-boot/2011.09/0001-HACK-beagleboard-config-disable-cache-for-USB.patch
> rename to recipes-bsp/u-boot/u-boot/2011.09/0015-HACK-beagleboard-config-disable-cache-for-USB.patch
> index a2776e9..ec1ec26 100644
> --- a/recipes-bsp/u-boot/u-boot/2011.09/0001-HACK-beagleboard-config-disable-cache-for-USB.patch
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0015-HACK-beagleboard-config-disable-cache-for-USB.patch
> @@ -1,7 +1,7 @@
> -From 03b9bca863257cb24d8f11bb773ad2b8dff820c6 Mon Sep 17 00:00:00 2001
> +From 3fe471d34ef6575bc49c9f85ed74368e3ac25ad6 Mon Sep 17 00:00:00 2001
> From: Jason Kridner <jdk at ti.com>
> Date: Sun, 18 Sep 2011 12:16:31 -0400
> -Subject: [PATCH 1/3] HACK: beagleboard: config: disable cache for USB
> +Subject: [PATCH 15/21] HACK: beagleboard: config: disable cache for USB
>
> There is currently a bug in the USB code for the BeagleBoard that is
> worked-around by disabling the cache.
> @@ -10,11 +10,11 @@ See http://comments.gmane.org/gmane.comp.boot-loaders.u-boot/108224
>
> Signed-off-by: Jason Kridner <jdk at ti.com>
> ---
> - include/configs/omap3_beagle.h | 5 +++++
> - 1 files changed, 5 insertions(+), 0 deletions(-)
> + include/configs/omap3_beagle.h | 4 ++++
> + 1 files changed, 4 insertions(+), 0 deletions(-)
>
> diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
> -index 1369c89..8a84d7a 100644
> +index 941ec38..569d747 100644
> --- a/include/configs/omap3_beagle.h
> +++ b/include/configs/omap3_beagle.h
> @@ -36,6 +36,10 @@
> @@ -29,5 +29,5 @@ index 1369c89..8a84d7a 100644
>
> #include <asm/arch/cpu.h> /* get chip and board defs */
> --
> -1.7.4.1
> +1.7.2.5
>
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0002-beagleboard-config-enable-gpio-command.patch b/recipes-bsp/u-boot/u-boot/2011.09/0016-beagleboard-config-enable-gpio-command.patch
> similarity index 77%
> rename from recipes-bsp/u-boot/u-boot/2011.09/0002-beagleboard-config-enable-gpio-command.patch
> rename to recipes-bsp/u-boot/u-boot/2011.09/0016-beagleboard-config-enable-gpio-command.patch
> index 096a1ce..268932b 100644
> --- a/recipes-bsp/u-boot/u-boot/2011.09/0002-beagleboard-config-enable-gpio-command.patch
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0016-beagleboard-config-enable-gpio-command.patch
> @@ -1,7 +1,7 @@
> -From 79e8280783d445f7630b8a9830f8db73f2e04828 Mon Sep 17 00:00:00 2001
> +From e5bf80f2fb4af9a2627541cb8bc8686e8a9e8404 Mon Sep 17 00:00:00 2001
> From: Jason Kridner <jdk at ti.com>
> Date: Tue, 6 Sep 2011 18:56:11 -0400
> -Subject: [PATCH 2/3] beagleboard: config: enable gpio command
> +Subject: [PATCH 16/21] beagleboard: config: enable gpio command
>
> Now that we are using the generic GPIO framework, enable the command.
> ---
> @@ -9,10 +9,10 @@ Now that we are using the generic GPIO framework, enable the command.
> 1 files changed, 1 insertions(+), 0 deletions(-)
>
> diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
> -index 8a84d7a..43dc94a 100644
> +index 569d747..337ca29 100644
> --- a/include/configs/omap3_beagle.h
> +++ b/include/configs/omap3_beagle.h
> -@@ -169,6 +169,7 @@
> +@@ -164,6 +164,7 @@
> #define CONFIG_CMD_PING
> #define CONFIG_CMD_DHCP
> #define CONFIG_CMD_SETEXPR /* Evaluate expressions */
> @@ -21,5 +21,5 @@ index 8a84d7a..43dc94a 100644
> #undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
> #undef CONFIG_CMD_FPGA /* FPGA configuration Support */
> --
> -1.7.4.1
> +1.7.2.5
>
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0003-Increased-some-timeout-durations-for-MMC-and-EHCI.patch b/recipes-bsp/u-boot/u-boot/2011.09/0017-Increased-some-timeout-durations-for-MMC-and-EHCI.patch
> similarity index 72%
> rename from recipes-bsp/u-boot/u-boot/2011.09/0003-Increased-some-timeout-durations-for-MMC-and-EHCI.patch
> rename to recipes-bsp/u-boot/u-boot/2011.09/0017-Increased-some-timeout-durations-for-MMC-and-EHCI.patch
> index c3ebf1b..9aeb548 100644
> --- a/recipes-bsp/u-boot/u-boot/2011.09/0003-Increased-some-timeout-durations-for-MMC-and-EHCI.patch
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0017-Increased-some-timeout-durations-for-MMC-and-EHCI.patch
> @@ -1,7 +1,7 @@
> -From 316e3a4573bdbbbc395baeca4f7b2208707e30fa Mon Sep 17 00:00:00 2001
> +From 7ba57c9e6372c067609797cbac53f8a14691fc2d Mon Sep 17 00:00:00 2001
> From: Jason Kridner <jdk at ti.com>
> Date: Wed, 7 Sep 2011 08:56:48 -0400
> -Subject: [PATCH 3/3] Increased some timeout durations for MMC and EHCI
> +Subject: [PATCH 17/21] Increased some timeout durations for MMC and EHCI
>
> ---
> drivers/mmc/omap_hsmmc.c | 2 +-
> @@ -9,18 +9,18 @@ Subject: [PATCH 3/3] Increased some timeout durations for MMC and EHCI
> 2 files changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/mmc/omap_hsmmc.c b/drivers/mmc/omap_hsmmc.c
> -index ef12ecd..7e35372 100644
> +index c38b9e6..5054a21 100644
> --- a/drivers/mmc/omap_hsmmc.c
> +++ b/drivers/mmc/omap_hsmmc.c
> -@@ -33,7 +33,7 @@
> +@@ -34,7 +34,7 @@
> #include <asm/arch/sys_proto.h>
>
> /* If we fail after 1 second wait, something is really bad */
> -#define MAX_RETRY_MS 1000
> +#define MAX_RETRY_MS 5000
>
> - static int mmc_read_data(hsmmc_t *mmc_base, char *buf, unsigned int size);
> - static int mmc_write_data(hsmmc_t *mmc_base, const char *buf, unsigned int siz);
> + static int mmc_read_data(struct hsmmc *mmc_base, char *buf, unsigned int size);
> + static int mmc_write_data(struct hsmmc *mmc_base, const char *buf,
> diff --git a/include/usb.h b/include/usb.h
> index 06170cd..0d99b92 100644
> --- a/include/usb.h
> @@ -35,5 +35,5 @@ index 06170cd..0d99b92 100644
> /* device request (setup) */
> struct devrequest {
> --
> -1.7.4.1
> +1.7.2.5
>
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0003-beagleboard-mount-rootfs-RO-instead-of-RW-at-boot.patch b/recipes-bsp/u-boot/u-boot/2011.09/0018-beagleboard-mount-rootfs-RO-instead-of-RW-at-boot.patch
> similarity index 64%
> rename from recipes-bsp/u-boot/u-boot/2011.09/0003-beagleboard-mount-rootfs-RO-instead-of-RW-at-boot.patch
> rename to recipes-bsp/u-boot/u-boot/2011.09/0018-beagleboard-mount-rootfs-RO-instead-of-RW-at-boot.patch
> index 3c6743e..b571a4e 100644
> --- a/recipes-bsp/u-boot/u-boot/2011.09/0003-beagleboard-mount-rootfs-RO-instead-of-RW-at-boot.patch
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0018-beagleboard-mount-rootfs-RO-instead-of-RW-at-boot.patch
> @@ -1,7 +1,7 @@
> -From 78080b20d8daa8e80f962beeab898d171bcc8eac Mon Sep 17 00:00:00 2001
> +From daa9fa5f66a1b370072f1e91fd51c6a5e3d81fd8 Mon Sep 17 00:00:00 2001
> From: Koen Kooi <koen at dominion.thruhere.net>
> -Date: Sun, 16 Oct 2011 09:37:38 +0200
> -Subject: [PATCH 3/3] beagleboard: mount rootfs RO instead of RW at boot
> +Date: Sun, 27 Nov 2011 14:43:58 +0100
> +Subject: [PATCH 18/21] beagleboard: mount rootfs RO instead of RW at boot
>
> Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> ---
> @@ -9,18 +9,18 @@ Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> 1 files changed, 1 insertions(+), 1 deletions(-)
>
> diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
> -index a67e5a0..95a134b 100644
> +index 337ca29..186586f 100644
> --- a/include/configs/omap3_beagle.h
> +++ b/include/configs/omap3_beagle.h
> -@@ -231,7 +231,7 @@
> +@@ -226,7 +226,7 @@
> "dvimode=640x480MR-16 at 60\0" \
> "defaultdisplay=dvi\0" \
> "mmcdev=0\0" \
> - "mmcroot=/dev/mmcblk0p2 rw\0" \
> + "mmcroot=/dev/mmcblk0p2 ro\0" \
> "mmcrootfstype=ext3 rootwait\0" \
> - "nandroot=/dev/mtdblock4 rw\0" \
> - "nandrootfstype=jffs2\0" \
> + "nandroot=ubi0:rootfs ubi.mtd=4\0" \
> + "nandrootfstype=ubifs\0" \
> --
> -1.6.6.1
> +1.7.2.5
>
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0002-beagleboard-switch-to-ttyO2.patch b/recipes-bsp/u-boot/u-boot/2011.09/0019-BeagleBoard-config-Really-switch-to-ttyO2.patch
> similarity index 57%
> rename from recipes-bsp/u-boot/u-boot/2011.09/0002-beagleboard-switch-to-ttyO2.patch
> rename to recipes-bsp/u-boot/u-boot/2011.09/0019-BeagleBoard-config-Really-switch-to-ttyO2.patch
> index bc7cf06..1d21612 100644
> --- a/recipes-bsp/u-boot/u-boot/2011.09/0002-beagleboard-switch-to-ttyO2.patch
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0019-BeagleBoard-config-Really-switch-to-ttyO2.patch
> @@ -1,7 +1,9 @@
> -From d901c32c1bd9343a932f8bdd96f3ec539407b42b Mon Sep 17 00:00:00 2001
> +From ceb3c55ff226f068edb369342e3bd2db70ca8827 Mon Sep 17 00:00:00 2001
> From: Koen Kooi <koen at dominion.thruhere.net>
> -Date: Tue, 11 Oct 2011 13:53:21 +0200
> -Subject: [PATCH 2/2] beagleboard: switch to ttyO2
> +Date: Sun, 27 Nov 2011 14:46:04 +0100
> +Subject: [PATCH 19/21] BeagleBoard: config: Really switch to ttyO2
> +
> +The previous commit changed it to "zero two" instead of the proper "Oh two". This was completely broken!
>
> Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> ---
> @@ -9,18 +11,18 @@ Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> 1 files changed, 1 insertions(+), 1 deletions(-)
>
> diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
> -index 23f19f6..04c2188 100644
> +index 186586f..833f86a 100644
> --- a/include/configs/omap3_beagle.h
> +++ b/include/configs/omap3_beagle.h
> -@@ -220,7 +220,7 @@
> +@@ -217,7 +217,7 @@
> "rdaddr=0x81000000\0" \
> "usbtty=cdc_acm\0" \
> "bootfile=uImage.beagle\0" \
> -- "console=ttyS2,115200n8\0" \
> +- "console=tty02,115200n8\0" \
> + "console=ttyO2,115200n8\0" \
> "mpurate=auto\0" \
> "buddy=none "\
> - "buddy2=none "\
> + "optargs=\0" \
> --
> -1.6.6.1
> +1.7.2.5
>
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0001-beagleboard-add-support-for-TCT-Beacon-board.patch b/recipes-bsp/u-boot/u-boot/2011.09/0020-beagleboard-add-support-for-TCT-Beacon-board.patch
> similarity index 81%
> rename from recipes-bsp/u-boot/u-boot/2011.09/0001-beagleboard-add-support-for-TCT-Beacon-board.patch
> rename to recipes-bsp/u-boot/u-boot/2011.09/0020-beagleboard-add-support-for-TCT-Beacon-board.patch
> index 819c623..39c2a36 100644
> --- a/recipes-bsp/u-boot/u-boot/2011.09/0001-beagleboard-add-support-for-TCT-Beacon-board.patch
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0020-beagleboard-add-support-for-TCT-Beacon-board.patch
> @@ -1,20 +1,19 @@
> -From f6ce74793e6341895153e43643460b7fc812dc9d Mon Sep 17 00:00:00 2001
> +From e368b3cc2b281146c7848a2044e8a7d457ea1e38 Mon Sep 17 00:00:00 2001
> From: Koen Kooi <koen at dominion.thruhere.net>
> Date: Sat, 8 Oct 2011 21:56:35 +0200
> -Subject: [PATCH] beagleboard: add support for TCT Beacon board
> +Subject: [PATCH 20/21] beagleboard: add support for TCT Beacon board
>
> Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> ---
> - board/ti/beagle/beagle.c | 59 ++++++++++++++++++++++++++++++++++++++++
> - board/ti/beagle/beagle.h | 7 +++++
> - include/configs/omap3_beagle.h | 7 +++++
> - 3 files changed, 73 insertions(+), 0 deletions(-)
> + board/ti/beagle/beagle.c | 10 ++++++++++
> + board/ti/beagle/beagle.h | 7 +++++++
> + 2 files changed, 17 insertions(+), 0 deletions(-)
>
> diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c
> -index 8cdceaf..f4e986c 100644
> +index 6a457cb..9c2e6d0 100644
> --- a/board/ti/beagle/beagle.c
> +++ b/board/ti/beagle/beagle.c
> -@@ -57,11 +57,14 @@ extern volatile struct ehci_hcor *hcor;
> +@@ -59,11 +59,14 @@ extern volatile struct ehci_hcor *hcor;
> #define TWL4030_I2C_BUS 0
> #define EXPANSION_EEPROM_I2C_BUS 1
> #define EXPANSION_EEPROM_I2C_ADDRESS 0x50
> @@ -29,7 +28,7 @@ index 8cdceaf..f4e986c 100644
> #define KBADC_BEAGLEFPGA 0x01000600
> #define LW_BEAGLETOUCH 0x01000700
> #define BRAINMUX_LCDOG 0x01000800
> -@@ -290,6 +331,13 @@ int misc_init_r(void)
> +@@ -351,6 +354,13 @@ int misc_init_r(void)
> setenv("defaultdisplay", "showdoglcd");
> setenv("buddy", "showdog");
> break;
> @@ -61,3 +60,6 @@ index 18bfaa8..6a9ad73 100644
> #define MUX_KBADC_BEAGLEFPGA() \
> MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTU | DIS | M1)) /*MCSPI4_CLK*/\
> MUX_VAL(CP(MCBSP1_DX), (IDIS | PTU | DIS | M1)) /*MCSPI4_SIMO*/\
> +--
> +1.7.2.5
> +
> diff --git a/recipes-bsp/u-boot/u-boot/2011.09/0001-beagleboard-add-support-for-scanning-loop-through-ex.patch b/recipes-bsp/u-boot/u-boot/2011.09/0021-beagleboard-add-support-for-scanning-loop-through-ex.patch
> similarity index 83%
> rename from recipes-bsp/u-boot/u-boot/2011.09/0001-beagleboard-add-support-for-scanning-loop-through-ex.patch
> rename to recipes-bsp/u-boot/u-boot/2011.09/0021-beagleboard-add-support-for-scanning-loop-through-ex.patch
> index fdd6200..a2df7ca 100644
> --- a/recipes-bsp/u-boot/u-boot/2011.09/0001-beagleboard-add-support-for-scanning-loop-through-ex.patch
> +++ b/recipes-bsp/u-boot/u-boot/2011.09/0021-beagleboard-add-support-for-scanning-loop-through-ex.patch
> @@ -1,7 +1,7 @@
> -From d6dd7efc7a74e6bdcbcbda204f66d4ad23fd0f53 Mon Sep 17 00:00:00 2001
> +From 78fd05bd746f623de3150469a9f6f4e9531a17c4 Mon Sep 17 00:00:00 2001
> From: Koen Kooi <koen at dominion.thruhere.net>
> -Date: Tue, 11 Oct 2011 13:05:32 +0200
> -Subject: [PATCH 1/2] beagleboard: add support for scanning loop-through expansionboards like the uLCD-lite
> +Date: Sun, 27 Nov 2011 14:53:56 +0100
> +Subject: [PATCH 21/21] beagleboard: add support for scanning loop-through expansionboards like the uLCD-lite
>
> Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> ---
> @@ -10,10 +10,10 @@ Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
> 2 files changed, 28 insertions(+), 4 deletions(-)
>
> diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c
> -index 96fac51..51a90a0 100644
> +index 9c2e6d0..5ea50d1 100644
> --- a/board/ti/beagle/beagle.c
> +++ b/board/ti/beagle/beagle.c
> -@@ -72,6 +72,7 @@ extern volatile struct ehci_hcor *hcor;
> +@@ -74,6 +74,7 @@ extern volatile struct ehci_hcor *hcor;
> #define BBTOYS_WIFI 0x01000B00
> #define BBTOYS_VGA 0x02000B00
> #define BBTOYS_LCD 0x03000B00
> @@ -21,7 +21,7 @@ index 96fac51..51a90a0 100644
> #define BEAGLE_NO_EEPROM 0xffffffff
>
> DECLARE_GLOBAL_DATA_PTR;
> -@@ -148,18 +149,18 @@ int get_board_revision(void)
> +@@ -209,18 +210,18 @@ void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
> * bus 1 for the availability of an AT24C01B serial EEPROM.
> * returns the device_vendor field from the EEPROM
> */
> @@ -43,7 +43,7 @@ index 96fac51..51a90a0 100644
> sizeof(expansion_config));
>
> i2c_set_bus_num(TWL4030_I2C_BUS);
> -@@ -262,7 +263,7 @@ int misc_init_r(void)
> +@@ -323,7 +324,7 @@ int misc_init_r(void)
> TWL4030_PM_RECEIVER_DEV_GRP_P1);
> }
>
> @@ -52,7 +52,7 @@ index 96fac51..51a90a0 100644
> case TINCANTOOLS_ZIPPY:
> printf("Recognized Tincantools Zippy board (rev %d %s)\n",
> expansion_config.revision,
> -@@ -341,6 +342,27 @@ int misc_init_r(void)
> +@@ -402,6 +403,27 @@ int misc_init_r(void)
> if (expansion_config.content == 1)
> setenv(expansion_config.env_var, expansion_config.env_setting);
>
> @@ -81,18 +81,18 @@ index 96fac51..51a90a0 100644
> switch (get_board_revision()) {
> case REVISION_XM_A:
> diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
> -index dbe682a..23f19f6 100644
> +index 833f86a..1cc46dc 100644
> --- a/include/configs/omap3_beagle.h
> +++ b/include/configs/omap3_beagle.h
> -@@ -223,6 +223,7 @@
> - "console=ttyS2,115200n8\0" \
> +@@ -220,6 +220,7 @@
> + "console=ttyO2,115200n8\0" \
> "mpurate=auto\0" \
> "buddy=none "\
> + "buddy2=none "\
> "optargs=\0" \
> "camera=none\0" \
> "vram=12M\0" \
> -@@ -239,6 +240,7 @@
> +@@ -236,6 +237,7 @@
> "${optargs} " \
> "mpurate=${mpurate} " \
> "buddy=${buddy} "\
> @@ -101,5 +101,5 @@ index dbe682a..23f19f6 100644
> "vram=${vram} " \
> "omapfb.mode=dvi:${dvimode} " \
> --
> -1.6.6.1
> +1.7.2.5
>
> diff --git a/recipes-bsp/u-boot/u-boot_2011.09.bb b/recipes-bsp/u-boot/u-boot_2011.09.bb
> index 8eef7c7..74c8518 100644
> --- a/recipes-bsp/u-boot/u-boot_2011.09.bb
> +++ b/recipes-bsp/u-boot/u-boot_2011.09.bb
> @@ -1,22 +1,41 @@
> require u-boot.inc
>
> -PR = "r4"
> +PR = "r5"
> +
> +# SPL build
> +UBOOT_BINARY = "u-boot.img"
> +UBOOT_IMAGE = "u-boot-${MACHINE}-${PV}-${PR}.img"
> +UBOOT_SYMLINK = "u-boot-${MACHINE}.img"
>
> # No patches for other machines yet
> COMPATIBLE_MACHINE = "(beagleboard)"
>
> SRC_URI = "git://www.denx.de/git/u-boot.git;protocol=git \
> - file://2011.09/0001-HACK-beagleboard-config-disable-cache-for-USB.patch \
> - file://2011.09/0002-beagleboard-config-enable-gpio-command.patch \
> - file://2011.09/0003-Increased-some-timeout-durations-for-MMC-and-EHCI.patch \
> - file://2011.09/0001-beagleboard-add-support-for-TCT-Beacon-board.patch \
> - file://2011.09/0001-beagleboard-add-support-for-scanning-loop-through-ex.patch \
> - file://2011.09/0002-beagleboard-switch-to-ttyO2.patch \
> - file://2011.09/0003-beagleboard-mount-rootfs-RO-instead-of-RW-at-boot.patch \
> + file://2011.09/0001-omap3-mem-Comment-enable_gpmc_cs_config-more.patch \
> + file://2011.09/0002-OMAP3-Update-SDRC-dram_init-to-always-call-make_cs1_.patch \
> + file://2011.09/0003-OMAP3-Add-a-helper-function-to-set-timings-in-SDRC.patch \
> + file://2011.09/0004-OMAP3-Change-mem_ok-to-clear-again-after-reading-bac.patch \
> + file://2011.09/0005-OMAP3-Remove-get_mem_type-prototype.patch \
> + file://2011.09/0006-omap3-mem-Add-MCFG-helper-macro.patch \
> + file://2011.09/0007-OMAP3-Add-optimal-SDRC-autorefresh-control-values.patch \
> + file://2011.09/0008-OMAP3-Suffix-all-Micron-memory-timing-parts-with-the.patch \
> + file://2011.09/0009-OMAP3-SPL-Rework-memory-initalization-and-devkit8000.patch \
> + file://2011.09/0010-OMAP3-SPL-Add-identify_nand_chip-function.patch \
> + file://2011.09/0011-OMAP3-Add-SPL-support-to-Beagleboard.patch \
> + file://2011.09/0012-OMAP3-Add-SPL-support-to-omap3_evm.patch \
> + file://2011.09/0013-AM3517-Add-SPL-support.patch \
> + file://2011.09/0014-AM3517-CraneBoard-Add-SPL-support.patch \
> + file://2011.09/0015-HACK-beagleboard-config-disable-cache-for-USB.patch \
> + file://2011.09/0016-beagleboard-config-enable-gpio-command.patch \
> + file://2011.09/0017-Increased-some-timeout-durations-for-MMC-and-EHCI.patch \
> + file://2011.09/0018-beagleboard-mount-rootfs-RO-instead-of-RW-at-boot.patch \
> + file://2011.09/0019-BeagleBoard-config-Really-switch-to-ttyO2.patch \
> + file://2011.09/0020-beagleboard-add-support-for-TCT-Beacon-board.patch \
> + file://2011.09/0021-beagleboard-add-support-for-scanning-loop-through-ex.patch \
> file://fw_env.config \
> "
>
> -SRCREV = "1d5e7fb403257d62f0f2419cb83fdf6b0f02f215"
> +SRCREV = "fdbe8b9a2d1858ba35dd6214315563ad44d4a0e3"
>
> LIC_FILES_CHKSUM = "file://COPYING;md5=1707d6db1d42237583f50183a5651ecb"
>
> --
> 1.7.2.5
>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 163 bytes
Desc: Message signed with OpenPGP using GPGMail
URL: <http://lists.yoctoproject.org/pipermail/meta-ti/attachments/20111129/af6f2eca/attachment.pgp>
More information about the meta-ti
mailing list