[meta-ti] [RESEND: PATCH 2/3] keystone2: u-boot: update to add gph support

[Tom Rini]

On 05/08/2013 11:55 AM, Karicheri, Muralidharan wrote:
>>> -----Original Message-----
>>> From: Rini, Tom
>>> Sent: Wednesday, May 08, 2013 11:11 AM
>>> To: Dmytriyenko, Denys
>>> Cc: Karicheri, Muralidharan; Hernandez, Carlos; meta-ti at yoctoproject.org
>>> Subject: Re: [meta-ti] [RESEND: PATCH 2/3] keystone2: u-boot: update to add gph
>>> support
>>>
>>> On 05/07/2013 06:40 PM, Denys Dmytriyenko wrote:
>>>> On Tue, May 07, 2013 at 06:07:10PM -0400, Karicheri, Muralidharan wrote:
>>> [snip]
>>>>>>>> +	cd ${DEPLOY_DIR_IMAGE}
>>>>>>>> +	rm -f ${UBOOT_BINARY} ${UBOOT_SYMLINK}
>>>>>>>> +	ln -sf ${UBOOT_IMAGE} ${UBOOT_SYMLINK}
>>>>>>>> +	ln -sf ${UBOOT_IMAGE} ${UBOOT_BINARY}
>>>>>>>> +	rm -f ${UBOOT_SPI_SPL_BINARY} ${UBOOT_SPI_SPL_SYMLINK}
>>>>>>>> +	ln -sf ${UBOOT_SPI_SPL_IMAGE} ${UBOOT_SPI_SPL_SYMLINK}
>>>>>>>> +	ln -sf ${UBOOT_SPI_SPL_IMAGE} ${UBOOT_SPI_SPL_BINARY}
>>>>>>>> +	rm -f ${UBOOT_SPI_BINARY} ${UBOOT_SPI_SYMLINK}
>>>>>>>> +	ln -sf ${UBOOT_SPI_IMAGE} ${UBOOT_SPI_SYMLINK}
>>>>>>>> +	ln -sf ${UBOOT_SPI_IMAGE} ${UBOOT_SPI_BINARY}
>>>>>>>> +	rm -f ${UBOOT_SPI_GPH_BINARY} ${UBOOT_SPI_GPH_SYMLINK}
>>>>>>>> +	ln -sf ${UBOOT_SPI_GPH_IMAGE} ${UBOOT_SPI_GPH_SYMLINK}
>>>>>>>> +	ln -sf ${UBOOT_SPI_GPH_IMAGE} ${UBOOT_SPI_GPH_BINARY} }
>>>>>>>
>>>>>>> As we just spoke - let's try to generalize this format and combine
>>>>>>> it with other similar requirements, like SPL-UART etc. There was a
>>>>>>> thread back in February about this...
>>>>>
>>>>> This is where I have disagreement. Let us restart the discussion. Who
>>>>> are the stake holders? Discuss it in this thread rather than using an
>>>>> old thread. I have copied here Carlos. I don't have bandwidth to
>>>>> spend too much time on this. Let us discuss it and identify what is required to be done.
>>>>
>>>> Sure, let's discuss. I encourage everyone to participate, especially
>>>> Carlos and Tom.
>>>
>>> We should try and get the generic u-boot.inc to allow for a few different variables to be
>>> set by the machine.conf file, and if they are, copy/symlink them as needed.  I think we
>>> should try and fit the SPI selection into the generic u-boot-with-spl.bin framework that
>>> exists in u-boot today if we can, and then add some logic so that we can package and
>>> symlink that single file instead.
> 
> I think we are unable to use the generic due to the specific header format requirement from RBL (Rom
> Boot loader). So we need to live with the format. How do we handle this with the existing u-boot-spl.gph
> formatting that we use?

I was off slightly it seems, we don't have everyone on
u-boot-with-spl.bin, but it's u-boot-with-spl.something (bin, imx).  So
in this case, make up the rules for a u-boot-with-spl.gph that does what
keystone needs, and we can finish up the rest of the logic around that
to pick up u-boot-with-spl.* and copy/link.

-- 
Tom