[meta-ti] u-boot build failure .lds file?

[Joshua Vanderpool]

Can not use // comments in header files. such as my custom board .h

Sorry for the extra messages.

Josh

On Wed, Dec 9, 2015 at 11:55 AM, Joshua Vanderpool <jdvdt2 at gmail.com> wrote:

> I finally got my custom board ported from the old method of the borads.cfg
> file.  The missing link was in the /arch/arm/cpu/armv7/omap5/Kconfig needed
> to add my board to get the autotools to get my source/headers.
>
> However the issue I face now is the failure to link I think, have no clue
> where this would come from.
>
>   arm-linux-gnueabihf-ld.bfd   -pie  --gc-sections -Bstatic -Ttext
> 0x80800000 -o u-boot -T u-boot.lds arch/arm/cpu/armv7/start.o --start-group
>  arch/arm/cpu/built-in.o  arch/arm/cpu/armv7/built-in.o
>  arch/arm/lib/built-in.o  board/ti/common/built-in.o
>  board/ti/raymond_gdm/built-in.o  common/built-in.o  disk/built-in.o
>  drivers/built-in.o  drivers/dma/built-in.o  drivers/gpio/built-in.o
>  drivers/i2c/built-in.o  drivers/mmc/built-in.o  drivers/mtd/built-in.o
>  drivers/mtd/onenand/built-in.o  drivers/mtd/spi/built-in.o
>  drivers/net/built-in.o  drivers/net/phy/built-in.o  drivers/pci/built-in.o
>  drivers/power/built-in.o  drivers/power/battery/built-in.o
>  drivers/power/fuel_gauge/built-in.o  drivers/power/mfd/built-in.o
>  drivers/power/pmic/built-in.o  drivers/power/regulator/built-in.o
>  drivers/serial/built-in.o  drivers/spi/built-in.o
>  drivers/usb/dwc3/built-in.o  drivers/usb/emul/built-in.o
>  drivers/usb/eth/built-in.o  drivers/usb/gadget/built-in.o
>  drivers/usb/gadget/udc/built-in.o  drivers/usb/host/built-in.o
>  drivers/usb/musb-new/built-in.o  drivers/usb/musb/built-in.o
>  drivers/usb/phy/built-in.o  drivers/usb/ulpi/built-in.o  fs/built-in.o
>  lib/built-in.o  net/built-in.o  test/built-in.o  test/dm/built-in.o
> --end-group arch/arm/lib/eabi_compat.o  -L
> /home/jvanderpool/gcc-linaro-4.9-2015.05-x86_64_arm-linux-gnueabihf/bin/../lib/gcc/arm-linux-gnueabihf/4.9.3
> -lgcc -Map u-boot.map
> arm-linux-gnueabihf-ld.bfd:u-boot.lds:1: ignoring invalid character `#' in
> expression
> arm-linux-gnueabihf-ld.bfd:u-boot.lds:1: syntax error
> make: *** [u-boot] Error 1
>
> Thanks for any support and your time.
>
> Josh
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.yoctoproject.org/pipermail/meta-ti/attachments/20151209/9b212cd5/attachment.html>