[meta-xilinx] failure : SD to u-boot SPL to u-boot on zcu102-zynqmp

[Jean-Francois Dagenais]

> On Mar 20, 2017, at 21:48, Jean-Francois Dagenais <jeff.dagenais at gmail.com> wrote:
> 
> 
>> On Mar 20, 2017, at 16:29, Jean-Francois Dagenais <jeff.dagenais at gmail.com> wrote:
>> 
>> So please advise, I was under the impression that I needed recent commits in
>> u-boot-xlnx related to SD for booting on it. Should I use another specific
>> version of u-boot-xlnx? Again, just want to get past all that and execute the
>> kernel so the rest of the teams can progress.
> 

Alright, so quick update before I head out til tomorrow...

I disabled GEM in the 1.0 defconfig (don't need it) and removed the 0.3 version check to see where it would fail next...

<debug_uart> Debug uart enabled

U-Boot SPL 2017.01 (Mar 20 2017 - 22:19:03)
EL Level:	EL3
Trying to boot from MMC1
reading u-boot.bin
reading atf-uboot.ub
reading atf-uboot.ub
NOTICE:  ATF running on XCZU9EG/silicon v3/RTL5.1 at 0xfffea000, with PMU firmware
NOTICE:  BL31: Secure code at 0x0
NOTICE:  BL31: Non secure code at 0x8000000
NOTICE:  BL31: v1.2(release):a9e3716
NOTICE:  BL31: Built : 16:41:21, Mar  9 2017
PMUFW: PmMmioRead: (NODE_APU) addr=0xFF5E0074, value=0x1010F00
PMUFW: PmMmioRead: (NODE_APU) addr=0xFF5E0020, value=0x15A00


U-Boot 2017.01 (Mar 20 2017 - 22:25:08 -0400) Xilinx ZynqMP ZCU102 rev1.0

I2C:   ready
DRAM:  4 GiB
EL Level:	EL2
Chip ID:	xczuunknown
PMUFW: PmMmioRead: (NODE_APU) addr=0xFF5E0074, value=0x1010F00
PMUFW: PmMmioRead: (NODE_APU) addr=0xFF5E0020, value=0x15A00
MMC:   PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180358, mask=0x40000, value=0x40000
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0x2000000, value=0x2000000
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0x1000000, value=0x1000000
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0xFF0000, value=0x150000
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0x2000000, value=0x0
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180318, mask=0x400000, value=0x400000
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180318, mask=0x3F0000, value=0x50000
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180358, mask=0x40000, value=0x0
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180358, mask=0x40000, value=0x40000
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0x2000000, value=0x2000000
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0x1000000, value=0x1000000
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0xFF0000, value=0x150000
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180314, mask=0x2000000, value=0x0
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180318, mask=0x400000, value=0x400000
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180318, mask=0x3F0000, value=0x50000
PMUFW: PmMmioWrite: (NODE_APU) addr=0xFF180358, mask=0x40000, value=0x0
sdhci at ff170000: 0 (SD)
reading uboot.env

** Unable to read "uboot.env" from mmc0:1 **
Using default environment

In:    serial at ff000000
Out:   serial at ff000000
Err:   serial at ff000000
PMUFW: PmMmioRead: (NODE_APU) ERROR: access denied for address 0xFF5E0200
initcall sequence 000000007ff8c2a0 failed at call 0000000008002d54 (err=-22)
### ERROR ### Please RESET the board ###