[meta-xilinx] Thud release update

[Manjukumar Harthikote Matha]

> -----Original Message-----
> From: Manjukumar Harthikote Matha
> Sent: Wednesday, December 12, 2018 11:42 AM
> To: Luca Ceresoli <luca at lucaceresoli.net>; meta-xilinx at yoctoproject.org
> Subject: RE: [meta-xilinx] Thud release update
> 
> Hi Luca,
> 
> > -----Original Message-----
> > From: Luca Ceresoli [mailto:luca at lucaceresoli.net]
> > Sent: Wednesday, December 12, 2018 8:31 AM
> > To: Manjukumar Harthikote Matha <MANJUKUM at xilinx.com>; meta-
> > xilinx at yoctoproject.org
> > Subject: Re: [meta-xilinx] Thud release update
> >
> > Hi Manjukumar,
> >
> > On 29/11/18 18:07, Manjukumar Harthikote Matha wrote:
> > > Hi All,
> > >
> > > Thud release branch is under-testing as of now, we will start sending patches
> next
> > week and start merging to master:
> > > Please check the tree here:
> > > https://github.com/Xilinx/meta-xilinx/commits/master-next
> > >
> > > Major changes:
> > > meta-xilinx-standalone layer to support building toolchain for MB and pmu-
> > firmware
> > > Proposal was sent here:
> > > https://lists.yoctoproject.org/pipermail/meta-xilinx/2018-
> September/004051.html
> > >
> > > There are two ways to build pmu-firmware: One using multiconfig and other as
> > two separate distros
> > >
> > > 1) multiconfig way:
> > > 	- You need to add the dependency in the image file, for example in core-
> > image-minimal you will need
> > > 	do_image[mcdepends] = "multiconfig:zcu102:pmu:pmu-
> > firmware:do_deploy"
> > >
> > >
> > > 	- Add conf/multiconfig in the build directory and create pmu.conf and
> > zcu102.conf under conf/multiconfig
> > >                pmu.conf  consists of
> > > 	MACHINE="zynqmp-pmu"
> > > 	DISTRO="xilinx-standalone"
> > >     	GCCVERSION="7.%"
> > >     	TMPDIR="${TOPDIR}/pmutmp"
> > >
> > > 	zcu102.conf consists of
> > > 	MACHINE="zcu102-zynqmp"
> > >     	DISTRO="poky"
> > >                - In local.conf multiconfig is enabled by: BBMULTICONFIG ?= "zcu102
> > pmu"
> > > 	- bitbake multiconfig:zcu102:core-image-minimal
> > >
> > > This will build pmu-firmware in   build/pmutmp and all the linux images in
> build/tmp
> >
> > [Disclaimer: I did not double-check everything I state below since it
> > takes hours for each test]
> >
> > I tried this setup and building u-boot-xlnx fails:
> >
> >   $ bitbake multiconfig:zcu102:core-image-minimal
> >   [...]
> >   Cannot read
> > ../../../../../../pmutmp/deploy/images/zynqmp-pmu/pmu-firmware-zynqmp-
> pmu.bin
> >
> > This can be reproduced with the attached script.
> >
> 
> From script it seems you are missing do_image[mcdepends] =
> "multiconfig:zcu102:pmu:pmu-firmware:do_deploy" in your image file?
> I think you could also add in local.conf
> 

Spoke too soon :)

You need both, we are looking into why both lines will be required.
In Local.conf
do_image[mcdepends] = "multiconfig:zcu102:pmu:pmu-firmware:do_deploy"
In u-boot-xlnx
do_compile[mcdepends] = "multiconfig:zcu102:pmu:pmu-firmware:do_deploy"

Thanks,
Manju